← Commit history

l7987tr: factory component page (tier=mfr)

Ray ·49d9011478 · ·parent 631fc1d
1 file changed +170−8
page.json+170−8
@@ -1,13 +1,180 @@ {+  "schema_version": 1,+  "type": "component",   "slug": "l7987tr",+  "title": "L7987TR",+  "brief": "STMicroelectronics DC-DC Converters, HTSSOP-16-EP. Datasheet-verified pinout, KiCad symbol/footprint/3D.",   "version": "0.1.0",-  "type": "component",-  "description": "STMicroelectronics DC-DC Converters, HTSSOP-16-EP. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "license": "CC-BY-SA-4.0",   "tags": [     "component",     "pmic",     "l7987tr"   ],+  "component": {+    "mpn": "L7987TR",+    "manufacturer": "STMicroelectronics",+    "package": "HTSSOP-16-EP",+    "pin_count": 17,+    "category": "PMIC",+    "subcategory": "DC-DC Converters",+    "datasheet": "https://www.st.com/resource/en/datasheet/l7987tr.pdf",+    "parts": {+      "symbol": "l7987tr.kicad_sym",+      "footprint": "l7987tr.kicad_mod",+      "model_3d": "l7987tr.glb",+      "model_3d_step": "l7987tr.step",+      "lbr": "l7987tr.lbr"+    },+    "distributor_links": {},+    "pins": [+      {+        "number": "1",+        "name": "VBIAS",+        "type": "power_in",+        "description": "Auxiliary input to supply part of the analog circuitry to increase efficiency at light load. Typically tied to the regulated output voltage or an external rail higher than 3 V; connect to signal GND (or bypass with a 1 uF ceramic) if unused."+      },+      {+        "number": "2",+        "name": "VIN",+        "type": "power_in",+        "description": "DC input voltage (4.5 V to 61 V operating range). Tie both VIN pins together at the package."+      },+      {+        "number": "3",+        "name": "VIN",+        "type": "power_in",+        "description": "DC input voltage (4.5 V to 61 V operating range). Tie both VIN pins together at the package."+      },+      {+        "number": "4",+        "name": "VCC",+        "type": "power_in",+        "description": "Filtered DC input voltage to the internal circuitry. Bypass to signal GND with a 1 uF ceramic capacitor."+      },+      {+        "number": "5",+        "name": "EN",+        "type": "input",+        "description": "Active-high enable pin (device OFF <= 0.30 V, ON >= 0.35 V). Connect to VCC if not used."+      },+      {+        "number": "6",+        "name": "SS",+        "type": "passive",+        "description": "Soft-start pin. An internal 5 uA typ. current source charges an external capacitor from this pin to set the soft-start time."+      },+      {+        "number": "7",+        "name": "SYNCH",+        "type": "bidirectional",+        "description": "Master/slave synchronization pin. Sources a pulse when configured as master and accepts an external sync input (>=280 kHz) when configured as slave; up to 5 slave devices can share this line."+      },+      {+        "number": "8",+        "name": "COMP",+        "type": "output",+        "description": "Error-amplifier output. Compensation network (Type II or Type III) is connected between COMP and FB/GND to shape the loop response."+      },+      {+        "number": "9",+        "name": "FB",+        "type": "input",+        "description": "Inverting input of the error amplifier (VFB = 0.8 V typ.). Connect to the output resistor divider to set the regulated output voltage."+      },+      {+        "number": "10",+        "name": "FSW",+        "type": "passive",+        "description": "Switching-frequency programming pin. A pull-down resistor to GND selects the switching frequency (250 kHz - 1.5 MHz); leaving FSW floating sets ~250 kHz."+      },+      {+        "number": "11",+        "name": "ILIM",+        "type": "passive",+        "description": "Peak-current-limit programming pin. A pull-down resistor to GND selects the inductor peak current limit; floating ILIM yields the default ~4.0 A limit."+      },+      {+        "number": "12",+        "name": "PGOOD",+        "type": "output",+        "description": "Open-collector power-good output. Pulled low when the FB voltage is out of regulation (rising threshold 0.70 V typ., 30 mV hysteresis); requires an external pull-up."+      },+      {+        "number": "13",+        "name": "LX",+        "type": "power_out",+        "description": "Switching node (output of the internal high-side n-DMOS). Tie both LX pins together and connect to the external inductor and freewheeling diode."+      },+      {+        "number": "14",+        "name": "LX",+        "type": "power_out",+        "description": "Switching node (output of the internal high-side n-DMOS). Tie both LX pins together and connect to the external inductor and freewheeling diode."+      },+      {+        "number": "15",+        "name": "BOOT",+        "type": "passive",+        "description": "Bootstrap pin for the high-side gate drive. Connect a 100 nF ceramic capacitor (typ.) between BOOT and LX; the internal regulator refreshes the boot capacitor during the off-time."+      },+      {+        "number": "16",+        "name": "GND",+        "type": "power_in",+        "description": "Signal ground reference for the internal analog circuitry."+      },+      {+        "number": "17",+        "name": "EP",+        "type": "power_in",+        "description": "Exposed thermal pad on package underside. Must be connected to signal GND and to a large copper area for heat dissipation (RthJA = 40 C/W on demo board)."+      }+    ],+    "provenance": {+      "extractor": "ds2sf",+      "datasheet": {+        "url": "https://www.st.com/resource/en/datasheet/l7987tr.pdf",+        "pages": 37,+        "sha256": "9ea1c120a6bc8ac2",+        "source_tier": "mfr"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 17,+        "described": 17,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "metadata": {+    "specs": {+      "Manufacturer": "STMicroelectronics",+      "Package": "HTSSOP-16-EP",+      "Category": "PMIC",+      "Pins": "17"+    }+  },+  "sections": [+    "hero",+    "viewers",+    "readme",+    "breadcrumbs",+    "info"+  ],+  "discovery_triggers": [+    "l7987tr"+  ],+  "discovery_pitch": "L7987TR (STMicroelectronics) component page with datasheet-verified CAD.",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  },   "dependencies": {},   "hero": {     "type": "image",@@ -25,10 +192,5 @@     "docs/l7987tr-datasheet.pdf",     "viewers/symbol.html",     "viewers/footprint.html"-  ],-  "visibility": "public",-  "author": {-    "name": "Ray",-    "email": "[email protected]"-  }+  ] }\ No newline at end of file