← Commit history

l6902d013tr: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·ad156efef3 · ·parent 3d3cbe8
1 file changed +75−1
page.json+75−1
@@ -33,5 +33,79 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "L6902D013TR",+    "manufacturer": "STMicroelectronics",+    "package": "SOIC-8",+    "pin_count": 8,+    "category": "DC-DC Converters",+    "datasheet": "https://www.st.com/resource/en/datasheet/l6902d013tr.pdf",+    "parts": {+      "symbol": "l6902d013tr.kicad_sym",+      "footprint": "l6902d013tr.kicad_mod",+      "model_3d": "l6902d013tr-etched.glb",+      "model_3d_plain": "l6902d013tr.glb",+      "model_3d_step": "l6902d013tr-etched.step",+      "model_3d_step_plain": "l6902d013tr.step",+      "lbr": "l6902d013tr.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "OUT",+        "type": "output",+        "description": "Regulator switching output. Drain of the internal P-channel DMOS power switch (typ. 250 mΩ) that drives the external inductor / catch diode of the step-down converter. Delivers up to 1 A continuous output current, internally limited (typ. 2.5 A latched short-circuit limit). Absolute maximum DC rating -1 V to 40 V (-5 V to 40 V peak, t ≤ 0.1 µs)."+      },+      {+        "number": "2",+        "name": "CS+",+        "type": "input",+        "description": "Positive (higher-voltage) input of the on-chip current error amplifier. Connect to the high side of the external current-sense resistor Rsense. Together with CS- programs the output current limit / constant-current setpoint via a ~100 mV internal offset (Voffs typ. 100 mV, ±5%). Absolute maximum -0.3 V to VCC."+      },+      {+        "number": "3",+        "name": "CS-",+        "type": "input",+        "description": "Negative (lower-voltage) input of the on-chip current error amplifier. Connect to the low side of the external current-sense resistor Rsense. Compatible with both VCC-referenced and GND-referenced sensing schemes, enabling accurate (±5%) programmable current limiting. Absolute maximum -0.3 V to VCC."+      },+      {+        "number": "4",+        "name": "COMP",+        "type": "output",+        "description": "Output of the internal voltage / current error amplifier, used for external loop frequency compensation. Connect an R-C compensation network from this pin to GND to set the control-loop bandwidth and phase margin. VOH ≈ 3.6 V (VFB = 1 V), VOL ≈ 0.4 V (VFB = 1.5 V); source ≈ 200 µA, sink ≈ 1 mA. Absolute maximum 4 V."+      },+      {+        "number": "5",+        "name": "FB",+        "type": "input",+        "description": "Step-down voltage-feedback input to the internal voltage error amplifier. Tie directly to VOUT for a 1.235 V (±2%) regulated output, or drive from an external R1/R2 divider to program higher outputs up to 34 V: VOUT = 1.235 V × (1 + R1/R2). Absolute maximum 4 V."+      },+      {+        "number": "6",+        "name": "VREF",+        "type": "power_out",+        "description": "Buffered 3.3 V (±2%) reference output. Can source up to ~5 mA of external load current (short-circuit current typ. 10 mA); line regulation 5 mV typ. over VCC = 8 V to 36 V, load regulation 8 mV typ. No output capacitor is required for stability."+      },+      {+        "number": "7",+        "name": "GND",+        "type": "power_in",+        "description": "Device ground / signal and power return. Ground reference for the reference, error amplifiers, oscillator, and control logic."+      },+      {+        "number": "8",+        "name": "VCC",+        "type": "power_in",+        "description": "Unregulated DC supply input. Operating range 8 V to 36 V (absolute maximum 40 V). Powers the internal control circuitry and the source of the integrated P-channel DMOS power switch. Bypass with a low-ESR capacitor close to the pin. Typical total operating quiescent current ~3 mA."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}