← Commit history

Initial commit: component/l6566btr

Ray ·6c885d2c88 ·
2 files changed +258
README.mdadded+52
@@ -0,0 +1,52 @@+# L6566BTR++**STMicroelectronics** · AC-DC Controllers And Regulators · SO-16++L6566BTR from STMicroelectronics, in a SO-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | HVS | input | High-voltage start-up input withstanding up to 700 V; internal 1 mA current source charges Vcc capacitor until IC turn-on threshold (13-15 V) is reached. |+| 2 | N.C. | unconnected | Not internally connected; provision for PCB clearance to meet safety requirements. |+| 3 | GND | power_in | Ground reference for signal and gate driver current return; must use separate PCB path from pulsed currents to avoid noise coupling. |+| 4 | GD | output | Gate driver output; totem pole stage with 800 mA peak source/sink current capability for driving MOSFET and IGBT gates. |+| 5 | Vcc | power_in | Supply voltage input with operating range 10.6 to 23 V after turn-on; IC disabled below adaptive UVLO threshold which reduces at light load. |+| 6 | FMOD | output | Frequency modulation output generating symmetrical triangular waveform via internal current sources charging external capacitor; connect resistor to OSC pin for spread-spectrum EMI reduction. |+| 7 | CS | input | Current sense input to PWM comparator with 150 ns minimum blanking time; 1.5 V second threshold triggers latched shutdown for transformer saturation or secondary diode short-circuit detection. |+| 8 | DIS | input | Latched disable input; voltage exceeding 4.5 V latches IC off reducing consumption; latch clears when Vcc falls below UVLO or AC_OK pulled low. |+| 9 | COMP | input | Feedback control input for loop regulation via phototransistor emitter current; operating range 2.5 to 5 V with internal 2 V bottom clamp; voltage below 1.4 V shuts down IC. |+| 10 | VREF | power_in | Accurate 5 V ± 2% internal voltage reference output supplying few mA to external circuits; IC latches off upon reference failure or drift detection. |+| 11 | ZCD | input | Zero current detector and overvoltage protection input from auxiliary winding; negative-going edge triggers MOSFET turn-on in QR mode; voltage above 5 V activates OVP shutdown. |+| 12 | MODE/SC | input | Operating mode selection input; tie to VREF for quasi-resonant mode (oscillator sets maximum frequency) or leave open for fixed-frequency mode (70% maximum duty cycle); delivers slope compensation ramp. |+| 13 | OSC | output | Oscillator frequency setting; internal 1 V voltage source with resistor to GND defining oscillator current; sets maximum frequency in QR mode or actual frequency in FF mode. |+| 14 | SS | input | Soft-start capacitor input charging from internal current source; progressive duty-cycle ramp during startup; also delays latched shutdown upon overload protection triggering. |+| 15 | VFF | input | Line voltage feedforward input with linear range 0 to 3 V modulating pulse-by-pulse current limit setpoint inversely; voltage above 3 V stops switching. |+| 16 | AC_OK | input | Brownout protection input with 0.45 V threshold; below threshold shuts down IC and clears latched protections; above threshold re-enables operation with internal 15 µA hysteresis current. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | STMicroelectronics |+| Package | SO-16 |+| Category | Power Management (PMIC) |+| Pins | 16 |++## CAD (KiCad official)++- Symbol: `L6566BTR`+- Footprint: `Package_SO:SOIC-16_3.9x9.9mm_P1.27mm`+- 3D model: SO-16 (KiCad packages3D, STEP)+- 3D model files: `l6566btr-etched.step` / `l6566btr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `l6566btr.step` / `l6566btr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8586194446882902016) (51 pp, sha256 `f4985aaaeab61abc`, retrieved 2026-10-03, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/l6566btr-datasheet.pdf)
page.jsonadded+206
@@ -0,0 +1,206 @@+{+  "slug": "l6566btr",+  "version": "0.1.0",+  "type": "component",+  "description": "STMicroelectronics AC-DC Controllers And Regulators, SO-16. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "l6566btr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "l6566btr.kicad_sym",+    "l6566btr.kicad_mod",+    "l6566btr.glb",+    "l6566btr.step",+    "l6566btr.lbr",+    "docs/hero.png",+    "docs/l6566btr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html",+    "l6566btr-hero.glb",+    "l6566btr-hero.overlay.json"+  ],+  "component": {+    "mpn": "L6566BTR",+    "manufacturer": "STMicroelectronics",+    "package": "SO-16",+    "pin_count": 16,+    "category": "Power Management (PMIC)",+    "subcategory": "AC-DC Controllers And Regulators",+    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8586194446882902016",+    "parts": {+      "symbol": "l6566btr.kicad_sym",+      "footprint": "l6566btr.kicad_mod",+      "model_3d": "l6566btr-hero.glb",+      "model_3d_plain": "l6566btr.glb",+      "model_3d_step": "l6566btr-etched.step",+      "model_3d_step_plain": "l6566btr.step",+      "lbr": "l6566btr.lbr"+    },+    "distributor_links": {+      "lcsc": 157453,+      "digikey": "497-6297-2-ND",+      "mouser": "511-L6566BTR"+    },+    "distributor_check": {+      "checked_at": "2026-10-03T02:41:24Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "497-6297-2-ND",+        "status": "found",+        "lifecycle": "Active"+      },+      "mouser": {+        "pn": "511-L6566BTR",+        "status": "found"+      }+    },+    "pins": [+      {+        "number": "1",+        "name": "HVS",+        "type": "input",+        "description": "High-voltage start-up input withstanding up to 700 V; internal 1 mA current source charges Vcc capacitor until IC turn-on threshold (13-15 V) is reached."+      },+      {+        "number": "2",+        "name": "N.C.",+        "type": "unconnected",+        "description": "Not internally connected; provision for PCB clearance to meet safety requirements."+      },+      {+        "number": "3",+        "name": "GND",+        "type": "power_in",+        "description": "Ground reference for signal and gate driver current return; must use separate PCB path from pulsed currents to avoid noise coupling."+      },+      {+        "number": "4",+        "name": "GD",+        "type": "output",+        "description": "Gate driver output; totem pole stage with 800 mA peak source/sink current capability for driving MOSFET and IGBT gates."+      },+      {+        "number": "5",+        "name": "Vcc",+        "type": "power_in",+        "description": "Supply voltage input with operating range 10.6 to 23 V after turn-on; IC disabled below adaptive UVLO threshold which reduces at light load."+      },+      {+        "number": "6",+        "name": "FMOD",+        "type": "output",+        "description": "Frequency modulation output generating symmetrical triangular waveform via internal current sources charging external capacitor; connect resistor to OSC pin for spread-spectrum EMI reduction."+      },+      {+        "number": "7",+        "name": "CS",+        "type": "input",+        "description": "Current sense input to PWM comparator with 150 ns minimum blanking time; 1.5 V second threshold triggers latched shutdown for transformer saturation or secondary diode short-circuit detection."+      },+      {+        "number": "8",+        "name": "DIS",+        "type": "input",+        "description": "Latched disable input; voltage exceeding 4.5 V latches IC off reducing consumption; latch clears when Vcc falls below UVLO or AC_OK pulled low."+      },+      {+        "number": "9",+        "name": "COMP",+        "type": "input",+        "description": "Feedback control input for loop regulation via phototransistor emitter current; operating range 2.5 to 5 V with internal 2 V bottom clamp; voltage below 1.4 V shuts down IC."+      },+      {+        "number": "10",+        "name": "VREF",+        "type": "power_in",+        "description": "Accurate 5 V ± 2% internal voltage reference output supplying few mA to external circuits; IC latches off upon reference failure or drift detection."+      },+      {+        "number": "11",+        "name": "ZCD",+        "type": "input",+        "description": "Zero current detector and overvoltage protection input from auxiliary winding; negative-going edge triggers MOSFET turn-on in QR mode; voltage above 5 V activates OVP shutdown."+      },+      {+        "number": "12",+        "name": "MODE/SC",+        "type": "input",+        "description": "Operating mode selection input; tie to VREF for quasi-resonant mode (oscillator sets maximum frequency) or leave open for fixed-frequency mode (70% maximum duty cycle); delivers slope compensation ramp."+      },+      {+        "number": "13",+        "name": "OSC",+        "type": "output",+        "description": "Oscillator frequency setting; internal 1 V voltage source with resistor to GND defining oscillator current; sets maximum frequency in QR mode or actual frequency in FF mode."+      },+      {+        "number": "14",+        "name": "SS",+        "type": "input",+        "description": "Soft-start capacitor input charging from internal current source; progressive duty-cycle ramp during startup; also delays latched shutdown upon overload protection triggering."+      },+      {+        "number": "15",+        "name": "VFF",+        "type": "input",+        "description": "Line voltage feedforward input with linear range 0 to 3 V modulating pulse-by-pulse current limit setpoint inversely; voltage above 3 V stops switching."+      },+      {+        "number": "16",+        "name": "AC_OK",+        "type": "input",+        "description": "Brownout protection input with 0.45 V threshold; below threshold shuts down IC and clears latched protections; above threshold re-enables operation with internal 15 µA hysteresis current."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.3",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.3",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [],+        "pages_sent": 12,+        "cost_usd": 0.1315,+        "at": "2026-10-03T02:40:46"+      },+      "datasheet": {+        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8586194446882902016",+        "pages": 51,+        "sha256": "f4985aaaeab61abc",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 16,+        "described": 16,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file