← Commit history

Initial commit: component/l4981ad013tr

Ray ·85915a310c ·
2 files changed +95
README.mdadded+61
@@ -0,0 +1,61 @@+# L4981AD013TR++**STMicroelectronics** · AC-DC Controllers and Regulators · SOIC-20-300mil++L4981AD013TR from STMicroelectronics, in a SOIC-20-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | P-GND | power_in | Power ground return for the high-current gate-driver output stage. Should be tied to the source of the boost MOSFET and, via a low-impedance star point, back to signal ground (pin 10). |+| 2 | IPK | input | Peak current limit sense input. On L4981A a single resistor between pin 2 and the current-sense resistor sets the peak-current threshold; a second resistor to VREF (pin 11) can be added for improved precision. Absolute max -0.3 to 5.5 V (-2 V for t<=1us). |+| 3 | OVP | input | Overvoltage protection input. An external resistor divider from the boost output is compared against an internal 5.1 V (typ) reference to clamp the peak output voltage. Absolute max -0.3 to 9 V. |+| 4 | IAC | input | AC current input. A current proportional to the rectified mains voltage (typically injected through a high-value resistor from the rectified line) is fed into the internal multiplier to generate the current reference. Absolute max input current 5 mA. |+| 5 | CA-OUT | output | Current amplifier output. An external RC compensation network from this pin to ISENSE (pin 9) sets the current-loop gain and bandwidth. Sink/source ~=20 mA, output range approx. -0.3 to 8.5 V. |+| 6 | LFF | input | Load feed-forward input. Modulates the multiplier output current in proportion to load for faster transient response; best control between 1.5 V and 5.3 V. If unused, tie to VREF (pin 11). Absolute max -0.3 to 9 V. |+| 7 | VRMS | input | RMS line-voltage feed-forward input. An external RC low-pass filter from the rectified line produces a DC voltage proportional to line RMS, compensating for input line variations. Recommended operating range 1.5 V to 5.5 V; if unused, tie to VREF (pin 11). Absolute max -0.3 to 9 V. |+| 8 | MULT-OUT | output | Multiplier output / current amplifier non-inverting input. High-impedance node; must not be pulled below -0.5 V. Absolute max -0.5 to 7 V. |+| 9 | ISENSE | input | Current amplifier inverting input, connected to the boost inductor current-sense resistor through an input resistor. High-impedance node; do not allow the pin to fall below -0.5 V. Absolute max -0.5 to 7 V. |+| 10 | S-GND | power_in | Signal (analog) ground. Return for the reference, error/current amplifiers, oscillator, and protection comparators. Kelvin-connect to P-GND (pin 1) at a single star point. |+| 11 | VREF | power_out | Buffered internal voltage reference output, 5.1 V typ, +/-2% (4.97 to 5.23 V over -25 degC to 85 degC). Internally current-limited, can source up to 10 mA to bias external circuitry (LFF, VRMS, IPK divider, etc.). |+| 12 | SS | output | Soft-start pin. An external capacitor to ground is charged by an internal 100 uA (typ) current source, ramping the reference to the error amplifier and setting the soft-start time. Internally discharged during UVLO or overvoltage. Absolute max -0.3 to 9 V. |+| 13 | VA-OUT | output | Voltage-loop error amplifier output. An external RC network sets the voltage-loop compensation. Output swing typically 0.4 V (low) to ~=6.5 V (high); source/sink capability 2-20 mA. Absolute max -0.3 to 8.5 V. |+| 14 | VFEED | input | Voltage error amplifier inverting input, driven by a resistive divider from the boost output to set the regulated DC bus voltage. Internally referenced to VREF (5.1 V). Absolute max -0.3 to 9 V. |+| 15 | P-UVLO | input | Programmable under-voltage lockout threshold input. A resistor divider from VCC (or the bootstrap supply) programs the turn-on threshold with hysteresis. Absolute max -0.3 to 7 V. |+| 16 | SYNC | bidirectional | L4981A synchronization I/O (CMOS logic compatible). As SYNC-in, a rectangular clock applied at this pin synchronizes the internal oscillator (VIH >= 3.5 V, VIL <= 0.9 V, pulse width >= 800 ns). As SYNC-out, the internal oscillator emits a ~=0.3-0.8 us wide clock pulse to synchronize other devices. Absolute max -0.3 to 7 V. |+| 17 | ROSC | passive | Oscillator timing resistor. An external resistor to ground (typ 24 kOhm) sets the constant charging current for COSC. Absolute max -0.3 to 3 V. |+| 18 | COSC | passive | Oscillator timing capacitor. An external capacitor to ground (typ 1 nF with ROSC = 24 kOhm gives ~=100 kHz) sets the switching frequency. Peak-charge current ~=0.55 mA, discharge ~=11.5 mA. Absolute max -0.3 to 7 V, sink 15 mA. |+| 19 | VCC | power_in | Chip supply input (self-limited to <= 50 mA). Typical operating range up to 19.5 V; the device features low start-up current (0.3 mA typ) so it can be bootstrapped from the rectified mains through a resistor and held up by an auxiliary winding. |+| 20 | GDRV | output | Gate driver output. Bipolar-plus-DMOS totem-pole stage delivering >1 A source and up to 2 A sink peak (t = 1 us) to drive the boost power MOSFET or IGBT. Peak gate-drive voltage -1 V min (t = 0.1 us). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | STMicroelectronics |+| Package | SOIC-20-300mil |+| Category | PMIC |+| Pins | 20 |++## Ordering variants++- `L4981AD013TR`+- `L4981AD013TRL4981BD`+- `L4981AD013TRL4981B`++## CAD (KiCad official)++- Symbol: `L4981AD013TR`+- Footprint: `Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm`+- 3D model: SOIC-20-300mil (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [STMicroelectronics datasheet](docs/l4981ad013tr-datasheet.pdf) (None pp, sha256 `607996fde19865e3`, retrieved 2026-08-17, tier: lcsc)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/l4981ad013tr-datasheet.pdf)
page.jsonadded+34
@@ -0,0 +1,34 @@+{+  "slug": "l4981ad013tr",+  "version": "0.1.0",+  "type": "component",+  "description": "STMicroelectronics AC-DC Controllers and Regulators, SOIC-20-300mil. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "pmic",+    "l4981ad013tr"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "l4981ad013tr.kicad_sym",+    "l4981ad013tr.kicad_mod",+    "l4981ad013tr.glb",+    "l4981ad013tr.step",+    "l4981ad013tr.lbr",+    "docs/hero.png",+    "docs/l4981ad013tr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "visibility": "public",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file