← Commit history

ksz8851snli-tr: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·7768f06af2 · ·parent a4d9152
1 file changed +224−1
page.json+224−1
@@ -33,5 +33,228 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "KSZ8851SNLI-TR",+    "manufacturer": "Microchip",+    "package": "QFN-32(5x5)",+    "pin_count": 33,+    "category": "Ethernet Controllers",+    "parts": {+      "symbol": "ksz8851snli-tr.kicad_sym",+      "footprint": "ksz8851snli-tr.kicad_mod",+      "model_3d": "ksz8851snli-tr-etched.glb",+      "model_3d_plain": "ksz8851snli-tr.glb",+      "model_3d_step": "ksz8851snli-tr-etched.step",+      "model_3d_step_plain": "ksz8851snli-tr.step",+      "lbr": "ksz8851snli-tr.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "LED0",+        "type": "output",+        "description": "Programmable LED0 output (open-drain-style, active LOW = LED on). Default indicates Link/Activity per CGCR[9]."+      },+      {+        "number": "2",+        "name": "PME",+        "type": "output",+        "description": "Power Management Event output (default active low, polarity set in PMECR). Asserted when a Wake-on-LAN event is detected, requesting host wake from low-power mode."+      },+      {+        "number": "3",+        "name": "INTRN",+        "type": "output",+        "description": "Interrupt Not - active-low interrupt output to host CPU when any enabled interrupt status bit is set. Requires an external 4.7 kΩ pull-up resistor."+      },+      {+        "number": "4",+        "name": "DGND",+        "type": "power_in",+        "description": "Digital IO ground."+      },+      {+        "number": "5",+        "name": "VDD_CO1.8",+        "type": "power_out",+        "description": "1.8V on-chip LDO regulator output. Feeds VDD_A1.8 (pin 9) and VDD_D1.8 (pin 23) for core supply. Leave floating if VDD_IO = 1.8V (core is then sourced from the external 1.8V rail)."+      },+      {+        "number": "6",+        "name": "EED_IO",+        "type": "bidirectional",+        "description": "EEPROM serial data (in/out) to external configuration EEPROM. Also a strap-in at reset: pull-up = EEPROM present, floating/pull-down = no EEPROM (default). Latched into CCR bit 9."+      },+      {+        "number": "7",+        "name": "EESK",+        "type": "output",+        "description": "EEPROM serial clock output to external EEPROM. Period is 4 µs (OBCR[1:0]=11 @25MHz) or 800 ns (OBCR[1:0]=00 @125MHz)."+      },+      {+        "number": "8",+        "name": "AGND",+        "type": "power_in",+        "description": "Analog ground."+      },+      {+        "number": "9",+        "name": "VDD_A1.8",+        "type": "power_in",+        "description": "1.8V analog supply. Normally tied to VDD_CO1.8 (pin 5) through appropriate filtering; if VDD_IO=1.8V, source from the same external 1.8V rail as VDD_IO."+      },+      {+        "number": "10",+        "name": "EECS",+        "type": "output",+        "description": "EEPROM chip-select output to external EEPROM."+      },+      {+        "number": "11",+        "name": "RXP",+        "type": "bidirectional",+        "description": "10/100 Ethernet media-dependent interface, positive side. Physical receive (MDI) or transmit (MDIX) - polarity assigned by Auto MDI-X."+      },+      {+        "number": "12",+        "name": "RXM",+        "type": "bidirectional",+        "description": "10/100 Ethernet media-dependent interface, negative side. Physical receive (MDI) or transmit (MDIX) - polarity assigned by Auto MDI-X."+      },+      {+        "number": "13",+        "name": "AGND",+        "type": "power_in",+        "description": "Analog ground."+      },+      {+        "number": "14",+        "name": "TXP",+        "type": "bidirectional",+        "description": "10/100 Ethernet media-dependent interface, positive side. Physical transmit (MDI) or receive (MDIX) - polarity assigned by Auto MDI-X."+      },+      {+        "number": "15",+        "name": "TXM",+        "type": "bidirectional",+        "description": "10/100 Ethernet media-dependent interface, negative side. Physical transmit (MDI) or receive (MDIX) - polarity assigned by Auto MDI-X."+      },+      {+        "number": "16",+        "name": "VDD_A3.3",+        "type": "power_in",+        "description": "3.3V analog VDD input supply for the PHY. Requires decoupling capacitors."+      },+      {+        "number": "17",+        "name": "ISET",+        "type": "passive",+        "description": "PHY transmit bias current set. Connect a 3.01 kΩ 1% resistor from this pin to ground."+      },+      {+        "number": "18",+        "name": "AGND",+        "type": "power_in",+        "description": "Analog ground."+      },+      {+        "number": "19",+        "name": "RSTN",+        "type": "input",+        "description": "Hardware reset, active-low. Must be held low for a minimum of 10 ms after the 3.3V supply is stable."+      },+      {+        "number": "20",+        "name": "X1",+        "type": "input",+        "description": "25 MHz crystal / oscillator input. Connect a 25 MHz crystal between X1 and X2, or drive X1 from a 3.3V-tolerant oscillator (leave X2 unconnected in that case). Clock accuracy ±50 ppm."+      },+      {+        "number": "21",+        "name": "X2",+        "type": "output",+        "description": "25 MHz crystal feedback output. Connects to the other terminal of the 25 MHz crystal at X1; leave NC when using an external oscillator on X1."+      },+      {+        "number": "22",+        "name": "DGND",+        "type": "power_in",+        "description": "Digital IO ground."+      },+      {+        "number": "23",+        "name": "VDD_D1.8",+        "type": "power_in",+        "description": "1.8V digital core supply. Normally tied to VDD_CO1.8 (pin 5) through appropriate filtering; if VDD_IO=1.8V, source from the same external 1.8V rail as VDD_IO."+      },+      {+        "number": "24",+        "name": "DGND",+        "type": "power_in",+        "description": "Digital IO ground."+      },+      {+        "number": "25",+        "name": "VDD_IO",+        "type": "power_in",+        "description": "Digital IO supply - accepts 3.3V, 2.5V, or 1.8V. Requires decoupling capacitors."+      },+      {+        "number": "26",+        "name": "CSN",+        "type": "input",+        "description": "SPI slave chip-select input, active low."+      },+      {+        "number": "27",+        "name": "SO",+        "type": "tri_state",+        "description": "SPI slave serial data out (MISO). Tri-stated when CSN is negated - requires an external 4.7 kΩ pull-up to keep the line high while the driver is tri-stated."+      },+      {+        "number": "28",+        "name": "SCLK",+        "type": "input",+        "description": "SPI slave serial clock input. Supports clock speeds up to 40 MHz."+      },+      {+        "number": "29",+        "name": "DGND",+        "type": "power_in",+        "description": "Digital IO ground."+      },+      {+        "number": "30",+        "name": "VDD_IO",+        "type": "power_in",+        "description": "Digital IO supply - accepts 3.3V, 2.5V, or 1.8V. Requires decoupling capacitors."+      },+      {+        "number": "31",+        "name": "SI",+        "type": "input",+        "description": "SPI slave serial data in (MOSI)."+      },+      {+        "number": "32",+        "name": "LED1",+        "type": "output",+        "description": "Programmable LED1 output (active LOW = LED on). Default indicates 100BASE-T activity per CGCR[9]; see LED0 (pin 1)."+      },+      {+        "number": "33",+        "name": "EP",+        "type": "power_in",+        "description": "Exposed thermal pad on bottom of QFN. Datasheet labels it 'Paddle Ground on Bottom of Chip' - connect to ground plane for electrical/thermal grounding."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}