← Commit history
README.mdadded+73@@ -0,0 +1,73 @@+# KSZ8851SNLI-TR++**Microchip** · Ethernet Controllers · QFN-32(5x5)++KSZ8851SNLI-TR from Microchip, in a QFN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | LED0 | output | Programmable LED0 output (open-drain-style, active LOW = LED on). Default indicates Link/Activity per CGCR[9]. |+| 2 | PME | output | Power Management Event output (default active low, polarity set in PMECR). Asserted when a Wake-on-LAN event is detected, requesting host wake from low-power mode. |+| 3 | INTRN | output | Interrupt Not - active-low interrupt output to host CPU when any enabled interrupt status bit is set. Requires an external 4.7 kΩ pull-up resistor. |+| 4 | DGND | power_in | Digital IO ground. |+| 5 | VDD_CO1.8 | power_out | 1.8V on-chip LDO regulator output. Feeds VDD_A1.8 (pin 9) and VDD_D1.8 (pin 23) for core supply. Leave floating if VDD_IO = 1.8V (core is then sourced from the external 1.8V rail). |+| 6 | EED_IO | bidirectional | EEPROM serial data (in/out) to external configuration EEPROM. Also a strap-in at reset: pull-up = EEPROM present, floating/pull-down = no EEPROM (default). Latched into CCR bit 9. |+| 7 | EESK | output | EEPROM serial clock output to external EEPROM. Period is 4 µs (OBCR[1:0]=11 @25MHz) or 800 ns (OBCR[1:0]=00 @125MHz). |+| 8 | AGND | power_in | Analog ground. |+| 9 | VDD_A1.8 | power_in | 1.8V analog supply. Normally tied to VDD_CO1.8 (pin 5) through appropriate filtering; if VDD_IO=1.8V, source from the same external 1.8V rail as VDD_IO. |+| 10 | EECS | output | EEPROM chip-select output to external EEPROM. |+| 11 | RXP | bidirectional | 10/100 Ethernet media-dependent interface, positive side. Physical receive (MDI) or transmit (MDIX) - polarity assigned by Auto MDI-X. |+| 12 | RXM | bidirectional | 10/100 Ethernet media-dependent interface, negative side. Physical receive (MDI) or transmit (MDIX) - polarity assigned by Auto MDI-X. |+| 13 | AGND | power_in | Analog ground. |+| 14 | TXP | bidirectional | 10/100 Ethernet media-dependent interface, positive side. Physical transmit (MDI) or receive (MDIX) - polarity assigned by Auto MDI-X. |+| 15 | TXM | bidirectional | 10/100 Ethernet media-dependent interface, negative side. Physical transmit (MDI) or receive (MDIX) - polarity assigned by Auto MDI-X. |+| 16 | VDD_A3.3 | power_in | 3.3V analog VDD input supply for the PHY. Requires decoupling capacitors. |+| 17 | ISET | passive | PHY transmit bias current set. Connect a 3.01 kΩ 1% resistor from this pin to ground. |+| 18 | AGND | power_in | Analog ground. |+| 19 | RSTN | input | Hardware reset, active-low. Must be held low for a minimum of 10 ms after the 3.3V supply is stable. |+| 20 | X1 | input | 25 MHz crystal / oscillator input. Connect a 25 MHz crystal between X1 and X2, or drive X1 from a 3.3V-tolerant oscillator (leave X2 unconnected in that case). Clock accuracy ±50 ppm. |+| 21 | X2 | output | 25 MHz crystal feedback output. Connects to the other terminal of the 25 MHz crystal at X1; leave NC when using an external oscillator on X1. |+| 22 | DGND | power_in | Digital IO ground. |+| 23 | VDD_D1.8 | power_in | 1.8V digital core supply. Normally tied to VDD_CO1.8 (pin 5) through appropriate filtering; if VDD_IO=1.8V, source from the same external 1.8V rail as VDD_IO. |+| 24 | DGND | power_in | Digital IO ground. |+| 25 | VDD_IO | power_in | Digital IO supply - accepts 3.3V, 2.5V, or 1.8V. Requires decoupling capacitors. |+| 26 | CSN | input | SPI slave chip-select input, active low. |+| 27 | SO | tri_state | SPI slave serial data out (MISO). Tri-stated when CSN is negated - requires an external 4.7 kΩ pull-up to keep the line high while the driver is tri-stated. |+| 28 | SCLK | input | SPI slave serial clock input. Supports clock speeds up to 40 MHz. |+| 29 | DGND | power_in | Digital IO ground. |+| 30 | VDD_IO | power_in | Digital IO supply - accepts 3.3V, 2.5V, or 1.8V. Requires decoupling capacitors. |+| 31 | SI | input | SPI slave serial data in (MOSI). |+| 32 | LED1 | output | Programmable LED1 output (active LOW = LED on). Default indicates 100BASE-T activity per CGCR[9]; see LED0 (pin 1). |+| 33 | EP | power_in | Exposed thermal pad on bottom of QFN. Datasheet labels it 'Paddle Ground on Bottom of Chip' - connect to ground plane for electrical/thermal grounding. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Microchip |+| Package | QFN-32(5x5) |+| Category | Interface |+| Pins | 33 |++## Ordering variants++- `KSZ8851SNLI-TR`+- `KSZ8851SNLI-TRKSZ8851SNL-TR`++## CAD (KiCad official)++- Symbol: `KSZ8851SNLI-TR`+- Footprint: `Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm`+- 3D model: QFN-32(5x5) (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Microchip datasheet](docs/ksz8851snli-tr-datasheet.pdf) (None pp, sha256 `aa3a99d09769cc45`, retrieved 2026-08-17, tier: manufacturer)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/ksz8851snli-tr-datasheet.pdf)
page.jsonadded+34@@ -0,0 +1,34 @@+{+ "slug": "ksz8851snli-tr",+ "version": "0.1.0",+ "type": "component",+ "description": "Microchip Ethernet Controllers, QFN-32(5x5). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "interface",+ "ksz8851snli-tr"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "ksz8851snli-tr.kicad_sym",+ "ksz8851snli-tr.kicad_mod",+ "ksz8851snli-tr.glb",+ "ksz8851snli-tr.step",+ "ksz8851snli-tr.lbr",+ "docs/hero.png",+ "docs/ksz8851snli-tr-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ],+ "visibility": "public",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}