← Commit history

Initial commit: component/ksz8081rnaia-tr

Ray ·7c7fcd8ada ·
2 files changed +101
README.mdadded+67
@@ -0,0 +1,67 @@+# KSZ8081RNAIA-TR++**Microchip** · Ethernet Controllers · QFN-24-EP(4x4)++KSZ8081RNAIA-TR from Microchip, in a QFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VDD_1.2 | power_in | 1.2 V core supply rail (sourced from the on-chip regulator). Decouple with 2.2 µF and 0.1 µF capacitors to ground. |+| 2 | VDDA_3.3 | power_in | 3.3 V analog supply rail for the PHY analog front-end. |+| 3 | RXM | bidirectional | Physical receive/transmit signal, negative differential line of the RX/TX pair to the magnetics (Auto MDI/MDI-X swaps RX/TX function). |+| 4 | RXP | bidirectional | Physical receive/transmit signal, positive differential line of the RX/TX pair to the magnetics (Auto MDI/MDI-X swaps RX/TX function). |+| 5 | TXM | bidirectional | Physical transmit/receive signal, negative differential line of the TX/RX pair to the magnetics (Auto MDI/MDI-X swaps TX/RX function). |+| 6 | TXP | bidirectional | Physical transmit/receive signal, positive differential line of the TX/RX pair to the magnetics (Auto MDI/MDI-X swaps TX/RX function). |+| 7 | XO | output | Crystal feedback output for the 25 MHz crystal reference. Leave as a no-connect when an external oscillator or clock source is used on XI. |+| 8 | XI | input | Reference clock input. In RMII 25 MHz mode accepts a 25 MHz ±50 ppm crystal, oscillator, or external clock. In RMII 50 MHz mode accepts a 50 MHz ±50 ppm oscillator/external clock. RNA power-up default is 25 MHz crystal on this pin. |+| 9 | REXT | passive | Sets PHY transmit output current bias. Connect an external 6.49 kΩ 1% resistor from this pin to ground. |+| 10 | MDIO | bidirectional | MII management interface data I/O. Open-drain with a weak internal pull-up; requires an external 1.0 kΩ pull-up resistor to VDDIO. |+| 11 | MDC | input | MII management interface clock input, synchronous with MDIO data. Has an internal pull-up. |+| 12 | RXD1 | output | RMII receive data bit 1 output to the MAC. Synchronous with the 50 MHz RMII reference clock; two bits per clock while CRS_DV is asserted. Internally pulled down during power-up/reset (strap-in), output otherwise. |+| 13 | RXD0 | output | RMII receive data bit 0 output to the MAC. Synchronous with the 50 MHz RMII reference clock; two bits per clock while CRS_DV is asserted. Internally pulled up during power-up/reset (strap-in), output otherwise. |+| 14 | VDDIO | power_in | Digital I/O supply rail. Selectable 3.3 V, 2.5 V, or 1.8 V to match the MAC logic level. |+| 15 | CRS_DV/PHYAD[1:0] | bidirectional | RMII Carrier Sense / Receive Data Valid output during normal operation. Latched at de-assertion of RST# as PHYAD[1:0]: pull-up → PHY address 0x03, pull-down (default) → PHY address 0x00. PHYAD[4:2] are fixed to 000. |+| 16 | REF_CLK | bidirectional | RMII 25 MHz mode: outputs the 50 MHz RMII reference clock to the MAC. RMII 50 MHz mode: no-connect (clock comes in on XI instead). RNA power-up default is 25 MHz mode (this pin drives 50 MHz out). |+| 17 | RXER | bidirectional | RMII receive-error output to the MAC. Must latch a pull-down value at the de-assertion of reset for normal operation; add an external pull-down if the MAC drives this line high at reset (or configure Register 16h Bit [15]). |+| 18 | INTRP | output | Programmable interrupt output to the MAC/host. Open-drain with a weak internal pull-up; requires an external 1.0 kΩ pull-up resistor to VDDIO. |+| 19 | TXEN | input | RMII transmit-enable input from the MAC. Asserted by the MAC while TXD[1:0] carry valid data (two bits per 50 MHz RMII reference clock period). |+| 20 | TXD0 | input | RMII transmit data bit 0 input from the MAC. Sampled on the 50 MHz RMII reference clock while TXEN is asserted. |+| 21 | TXD1 | bidirectional | RMII transmit data bit 1 input from the MAC during normal operation. In NAND Tree mode this pin is used as the NAND Tree output for parametric fault-detection testing. |+| 22 | GND | power_in | Device ground return. |+| 23 | LED0/ANEN_SPEED | bidirectional | Programmable LED0 output during normal operation (modes selected via Register 1Fh bits [5:4]). Latched at reset de-assertion as ANEN_SPEED strap: pull-up (default) enables auto-negotiation and selects 100 Mbps; pull-down disables auto-negotiation and selects 10 Mbps. Values load into Register 0h bits [12]/[13] and Register 4h. |+| 24 | RST# | input | Active-low chip reset input. Internal pull-up; drive low to reset the device. |+| 25 | PAD | power_in | Exposed thermal paddle on the bottom of the QFN. Must be soldered to the board ground plane. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Microchip |+| Package | QFN-24-EP(4x4) |+| Category | Interface |+| Pins | 25 |++## Ordering variants++- `KSZ8081RNAIA-TR`+- `KSZ8081RNAIA-TRRNACA`+- `KSZ8081RNAIA-TRRNDIA`+- `KSZ8081RNAIA-TRRNDCA`++## CAD (KiCad official)++- Symbol: `KSZ8081RNAIA-TR`+- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.7x2.7mm`+- 3D model: QFN-24-EP(4x4) (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Microchip datasheet](docs/ksz8081rnaia-tr-datasheet.pdf) (None pp, sha256 `6d02bb0e0b96569f`, retrieved 2026-08-17, tier: manufacturer)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/ksz8081rnaia-tr-datasheet.pdf)
page.jsonadded+34
@@ -0,0 +1,34 @@+{+  "slug": "ksz8081rnaia-tr",+  "version": "0.1.0",+  "type": "component",+  "description": "Microchip Ethernet Controllers, QFN-24-EP(4x4). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "interface",+    "ksz8081rnaia-tr"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "ksz8081rnaia-tr.kicad_sym",+    "ksz8081rnaia-tr.kicad_mod",+    "ksz8081rnaia-tr.glb",+    "ksz8081rnaia-tr.step",+    "ksz8081rnaia-tr.lbr",+    "docs/hero.png",+    "docs/ksz8081rnaia-tr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "visibility": "public",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file