← Commit history

Initial commit: component/isl6752aaza-t

Ray ·eacd3a4d25 ·
2 files changed +89
README.mdadded+55
@@ -0,0 +1,55 @@+# ISL6752AAZA-T++**RENESAS** · DC-DC Converters · QSOP-16-150mil++ISL6752AAZA-T from RENESAS, in a QSOP-16-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VADJ | input | 0 V to 5.0 V control input that sets the phase relationship between the SR outputs (OUTLLN/OUTLRN) and the lower PWM outputs (OUTLL/OUTLR). VADJ < 2.425 V advances the SR outputs; VADJ > 2.575 V delays them; 2.50 V ±75 mV gives zero phase difference. A weak internal 50% divider from VREF holds the pin at ~2.5 V when left open. |+| 2 | VREF | power_out | 5.0 V ±3% precision reference output over line, load and temperature. Sources up to 10 mA and sinks at least 5 mA; short-circuit current limited to -15 mA to -100 mA. Bypass to GND with a 0.1 µF to 2.2 µF low-ESR capacitor. |+| 3 | VERR | input | Inverting input of the PWM comparator; accepts the external error-amplifier signal directly or via an opto-coupler for closed-loop regulation. Internally pulled up by a nominal 1 mA current source; VOH is at least 4.20 V open circuit. Zero-duty-cycle occurs when VERR < ~0.85-1.20 V. |+| 4 | CTBUF | output | Buffered replica of the CT sawtooth oscillator waveform, capable of sourcing 2 mA. Nominal valley-to-peak gain of 2 V/V with a 0.40 V offset above GND. Suitable for slope compensation. |+| 5 | RTD | input | Oscillator timing-capacitor discharge current programming pin; nominal 2.0 V. The current in a resistor from RTD to GND sets the CT discharge current (nominally 20× the resistor current), which determines the PWM dead time. Maximum recommended RTD current is 1 mA (20 mA CT discharge). |+| 6 | RESDEL | input | Sets the resonant delay between the toggle of the upper FETs and the turn-on of a lower FET. Applied voltage 0 V to 2 V scales resonant delay from 0 % to 100 % of the dead time (V/2 = fraction of dead time); operate below 2 V so the lower FETs are OFF before the uppers switch. |+| 7 | CS | input | Overcurrent-comparator input; nominal 1.00 V threshold with 70 ns leading-edge blanking and ~35 ns CS-to-OUT delay (excluding LEB). Internally shorted to GND (≤20 Ω) at the termination of each PWM output. Input bias current is -2 µA to -6 µA at VCS = 0.3 V; a series input resistor may be required with high-impedance sense sources. |+| 8 | CT | passive | Oscillator timing capacitor node. CT is charged from GND by an internal 200 µA source (valley 0.80 V, peak 2.80 V, 2.0 Vp-p) and discharged by a user-adjustable current set through RTD. |+| 9 | OUTLL | output | Lower-left bridge FET gate drive. Pulse-width-modulated, operates in alternate sequence with OUTLR. Peak gate current 0.1 A (per absolute max), rise/fall ~110/90 ns into 220 pF at VDD = 15 V; clamped to ≤1.25 V during UVLO. |+| 10 | GND | power_in | Signal and power ground return for the device. A low-impedance layout with ground planes and short traces is required because of high peak gate currents and high-frequency operation. |+| 11 | OUTLRN | output | Complement of the lower-right PWM output OUTLR, suitable for driving synchronous rectifiers. Phase relative to OUTLR is controlled by VADJ (advance for VADJ < 2.425 V, delay for VADJ > 2.575 V, up to ±40 ns to ±300 ns). |+| 12 | OUTLLN | output | Complement of the lower-left PWM output OUTLL, suitable for driving synchronous rectifiers. Phase relative to OUTLL is controlled by VADJ (see VADJ description). |+| 13 | OUTUR | output | Upper-right bridge FET gate drive. Operates at fixed 50% duty cycle in alternate sequence with OUTUL. Peak gate current 0.1 A; UVLO output clamp ≤1.25 V. |+| 14 | OUTUL | output | Upper-left bridge FET gate drive. Operates at fixed 50% duty cycle in alternate sequence with OUTUR. Peak gate current 0.1 A; UVLO output clamp ≤1.25 V. |+| 15 | OUTLR | output | Lower-right bridge FET gate drive. Pulse-width-modulated, operates in alternate sequence with OUTLL. Peak gate current 0.1 A, rise/fall ~110/90 ns into 220 pF at VDD = 15 V; clamped to ≤1.25 V during UVLO. |+| 16 | VDD | power_in | Bias supply, recommended 9 V to 16 V (absolute max 20 V). Monitored by UVLO (typ 8.75 V start / 7.00 V stop, 1.75 V hysteresis). Start-up current 175 µA typ, operating current 11 mA typ. Bypass to GND with a ceramic capacitor as close to VDD/GND as possible. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | RENESAS |+| Package | QSOP-16-150mil |+| Category | PMIC |+| Pins | 16 |++## Ordering variants++- `ISL6752AAZA-T`++## CAD (KiCad official)++- Symbol: `ISL6752AAZA-T`+- Footprint: `Package_SO:QSOP-16_3.9x4.9mm_P0.635mm`+- 3D model: QSOP-16-150mil (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [RENESAS datasheet](docs/isl6752aaza-t-datasheet.pdf) (None pp, sha256 `3e5ee7fd5b5148da`, retrieved 2026-08-17, tier: lcsc)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/isl6752aaza-t-datasheet.pdf)
page.jsonadded+34
@@ -0,0 +1,34 @@+{+  "slug": "isl6752aaza-t",+  "version": "0.1.0",+  "type": "component",+  "description": "RENESAS DC-DC Converters, QSOP-16-150mil. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "pmic",+    "isl6752aaza-t"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "isl6752aaza-t.kicad_sym",+    "isl6752aaza-t.kicad_mod",+    "isl6752aaza-t.glb",+    "isl6752aaza-t.step",+    "isl6752aaza-t.lbr",+    "docs/hero.png",+    "docs/isl6752aaza-t-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "visibility": "public",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file