← Commit history
isl6752aaza-t: restore the component block (pinout + model declarations) from this page's own README and symbol
1 file changed
+122−1
page.json+122−1@@ -33,5 +33,126 @@ "author": { "name": "Ray", "email": "[email protected]"+ },+ "component": {+ "mpn": "ISL6752AAZA-T",+ "manufacturer": "RENESAS",+ "package": "QSOP-16-150mil",+ "pin_count": 16,+ "category": "DC-DC Converters",+ "parts": {+ "symbol": "isl6752aaza-t.kicad_sym",+ "footprint": "isl6752aaza-t.kicad_mod",+ "model_3d": "isl6752aaza-t-etched.glb",+ "model_3d_plain": "isl6752aaza-t.glb",+ "model_3d_step": "isl6752aaza-t-etched.step",+ "model_3d_step_plain": "isl6752aaza-t.step",+ "lbr": "isl6752aaza-t.lbr"+ },+ "pins": [+ {+ "number": "1",+ "name": "VADJ",+ "type": "input",+ "description": "0 V to 5.0 V control input that sets the phase relationship between the SR outputs (OUTLLN/OUTLRN) and the lower PWM outputs (OUTLL/OUTLR). VADJ < 2.425 V advances the SR outputs; VADJ > 2.575 V delays them; 2.50 V ±75 mV gives zero phase difference. A weak internal 50% divider from VREF holds the pin at ~2.5 V when left open."+ },+ {+ "number": "2",+ "name": "VREF",+ "type": "power_out",+ "description": "5.0 V ±3% precision reference output over line, load and temperature. Sources up to 10 mA and sinks at least 5 mA; short-circuit current limited to -15 mA to -100 mA. Bypass to GND with a 0.1 µF to 2.2 µF low-ESR capacitor."+ },+ {+ "number": "3",+ "name": "VERR",+ "type": "input",+ "description": "Inverting input of the PWM comparator; accepts the external error-amplifier signal directly or via an opto-coupler for closed-loop regulation. Internally pulled up by a nominal 1 mA current source; VOH is at least 4.20 V open circuit. Zero-duty-cycle occurs when VERR < ~0.85-1.20 V."+ },+ {+ "number": "4",+ "name": "CTBUF",+ "type": "output",+ "description": "Buffered replica of the CT sawtooth oscillator waveform, capable of sourcing 2 mA. Nominal valley-to-peak gain of 2 V/V with a 0.40 V offset above GND. Suitable for slope compensation."+ },+ {+ "number": "5",+ "name": "RTD",+ "type": "input",+ "description": "Oscillator timing-capacitor discharge current programming pin; nominal 2.0 V. The current in a resistor from RTD to GND sets the CT discharge current (nominally 20× the resistor current), which determines the PWM dead time. Maximum recommended RTD current is 1 mA (20 mA CT discharge)."+ },+ {+ "number": "6",+ "name": "RESDEL",+ "type": "input",+ "description": "Sets the resonant delay between the toggle of the upper FETs and the turn-on of a lower FET. Applied voltage 0 V to 2 V scales resonant delay from 0 % to 100 % of the dead time (V/2 = fraction of dead time); operate below 2 V so the lower FETs are OFF before the uppers switch."+ },+ {+ "number": "7",+ "name": "CS",+ "type": "input",+ "description": "Overcurrent-comparator input; nominal 1.00 V threshold with 70 ns leading-edge blanking and ~35 ns CS-to-OUT delay (excluding LEB). Internally shorted to GND (≤20 Ω) at the termination of each PWM output. Input bias current is -2 µA to -6 µA at VCS = 0.3 V; a series input resistor may be required with high-impedance sense sources."+ },+ {+ "number": "8",+ "name": "CT",+ "type": "passive",+ "description": "Oscillator timing capacitor node. CT is charged from GND by an internal 200 µA source (valley 0.80 V, peak 2.80 V, 2.0 Vp-p) and discharged by a user-adjustable current set through RTD."+ },+ {+ "number": "9",+ "name": "OUTLL",+ "type": "output",+ "description": "Lower-left bridge FET gate drive. Pulse-width-modulated, operates in alternate sequence with OUTLR. Peak gate current 0.1 A (per absolute max), rise/fall ~110/90 ns into 220 pF at VDD = 15 V; clamped to ≤1.25 V during UVLO."+ },+ {+ "number": "10",+ "name": "GND",+ "type": "power_in",+ "description": "Signal and power ground return for the device. A low-impedance layout with ground planes and short traces is required because of high peak gate currents and high-frequency operation."+ },+ {+ "number": "11",+ "name": "OUTLRN",+ "type": "output",+ "description": "Complement of the lower-right PWM output OUTLR, suitable for driving synchronous rectifiers. Phase relative to OUTLR is controlled by VADJ (advance for VADJ < 2.425 V, delay for VADJ > 2.575 V, up to ±40 ns to ±300 ns)."+ },+ {+ "number": "12",+ "name": "OUTLLN",+ "type": "output",+ "description": "Complement of the lower-left PWM output OUTLL, suitable for driving synchronous rectifiers. Phase relative to OUTLL is controlled by VADJ (see VADJ description)."+ },+ {+ "number": "13",+ "name": "OUTUR",+ "type": "output",+ "description": "Upper-right bridge FET gate drive. Operates at fixed 50% duty cycle in alternate sequence with OUTUL. Peak gate current 0.1 A; UVLO output clamp ≤1.25 V."+ },+ {+ "number": "14",+ "name": "OUTUL",+ "type": "output",+ "description": "Upper-left bridge FET gate drive. Operates at fixed 50% duty cycle in alternate sequence with OUTUR. Peak gate current 0.1 A; UVLO output clamp ≤1.25 V."+ },+ {+ "number": "15",+ "name": "OUTLR",+ "type": "output",+ "description": "Lower-right bridge FET gate drive. Pulse-width-modulated, operates in alternate sequence with OUTLL. Peak gate current 0.1 A, rise/fall ~110/90 ns into 220 pF at VDD = 15 V; clamped to ≤1.25 V during UVLO."+ },+ {+ "number": "16",+ "name": "VDD",+ "type": "power_in",+ "description": "Bias supply, recommended 9 V to 16 V (absolute max 20 V). Monitored by UVLO (typ 8.75 V start / 7.00 V stop, 1.75 V hysteresis). Start-up current 175 µA typ, operating current 11 mA typ. Bypass to GND with a ceramic capacitor as close to VDD/GND as possible."+ }+ ],+ "provenance": {+ "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ } }-}+}