← Commit history

is32lt3961-zla3-tr: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·87619b7aa8 · ·parent 1ea7dd6
1 file changed +128−1
page.json+128−1
@@ -33,5 +33,132 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "IS32LT3961-ZLA3-TR",+    "manufacturer": "ISSI Integrated Silicon Solution",+    "package": "TSSOP-16-EP",+    "pin_count": 17,+    "category": "LED Drivers",+    "parts": {+      "symbol": "is32lt3961-zla3-tr.kicad_sym",+      "footprint": "is32lt3961-zla3-tr.kicad_mod",+      "model_3d": "is32lt3961-zla3-tr-etched.glb",+      "model_3d_plain": "is32lt3961-zla3-tr.glb",+      "model_3d_step": "is32lt3961-zla3-tr-etched.step",+      "model_3d_step_plain": "is32lt3961-zla3-tr.step",+      "lbr": "is32lt3961-zla3-tr.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "VCC",+        "type": "power_in",+        "description": "Power supply input, 5V to 60V (absolute max 66V). Connect a bypass capacitor CVCC (4.7µF typ.) to ground; route from CVCC to GND and VCC as short as possible."+      },+      {+        "number": "2",+        "name": "TON",+        "type": "input",+        "description": "On-time setting pin. Connect a resistor RTON from this pin to VCC to set the constant on-time (switching frequency) for the COT buck controller."+      },+      {+        "number": "3",+        "name": "EN/PWM",+        "type": "input",+        "description": "Logic input for enable and PWM dimming. Pull above VIH (2V typ., 1.4V min) to enable, below VIL (0.8V typ., 0.4V) to disable. Accepts a 100Hz-20kHz PWM signal to dim LED brightness. High-voltage tolerant; internal 200kΩ pull-down."+      },+      {+        "number": "4",+        "name": "AGND",+        "type": "power_in",+        "description": "Analog ground reference for the internal control circuitry and small-signal setting components."+      },+      {+        "number": "5",+        "name": "FAULTB",+        "type": "output",+        "description": "Open-drain diagnostic output. Active low to indicate fault conditions (LED open/short, single LED short, RIS/BOOT/RTON faults, thermal shutdown, etc.). Requires external pull-up (typ. 10kΩ). VOL ≤ 0.2V at IOL = 5mA; leakage ≤ 1µA with 6V pull-up."+      },+      {+        "number": "6",+        "name": "VDD",+        "type": "power_out",+        "description": "Internal 6V (typ., 5.8-6.2V) LDO output that powers internal control circuits. Connect a 1µF X7R ceramic cap to GND placed as close to VDD as possible. May supply reference to ADIM or pull-up for FAULTB; current limit 22-37mA."+      },+      {+        "number": "7",+        "name": "ADIM",+        "type": "input",+        "description": "Analog dimming input. Voltage 0.4V-2V linearly scales the current-sense regulation threshold (VIS); >2.1V disables analog dimming (100% output); <0.28V forces output off. Never leave floating. Input current: 0nA (VADIM<2V), −25nA (VADIM>2V)."+      },+      {+        "number": "8",+        "name": "IMON",+        "type": "output",+        "description": "Output current monitor. Analog buffered voltage representing the LED current: VIMON = (VISP − VISN) × 8 + 0.4V. Up to ~VDD (6V). Can drive host ADC through a resistor divider if needed."+      },+      {+        "number": "9",+        "name": "SCD",+        "type": "input",+        "description": "LED short-circuit detection threshold input. Connect a resistor divider (RSCD1/RSCD2) from LED+ to GND. FAULTB asserts when VSCD falls below VSCD_TH (1.15V typ., 50mV hysteresis). Never leave floating; if unused, tie to ISN via 10kΩ."+      },+      {+        "number": "10",+        "name": "ISN",+        "type": "input",+        "description": "Current-sense negative input for the high-side LED current sense resistor RIS. Together with ISP forms the average LED current sense (VIS = 200mV typ. for 100% load)."+      },+      {+        "number": "11",+        "name": "ISP",+        "type": "input",+        "description": "Current-sense positive input. Sense element RIS is connected between ISP and ISN across the high-side path. ISP bias current: 176µA (VISN=12V) or −50µA (VISN=0V)."+      },+      {+        "number": "12",+        "name": "VOUT",+        "type": "input",+        "description": "Output voltage sense pin. Feeds the COT timer and control loop with the buck output voltage information."+      },+      {+        "number": "13",+        "name": "SGND",+        "type": "power_in",+        "description": "Power/signal ground for the low-side current sense. The CS sense resistor RCS MUST be connected to this ground pin for precise sensing."+      },+      {+        "number": "14",+        "name": "CS",+        "type": "input",+        "description": "Current ripple sense input. Senses the inductor current ripple during the high-side MOSFET off-time via low-side resistor RCS for loop control, valley current limit (VCS_TH1 = 50mV typ.), and inductor peak current limit (VCS_TH2 = 100mV typ.)."+      },+      {+        "number": "15",+        "name": "BOOT",+        "type": "passive",+        "description": "Bootstrap capacitor node for the internal high-side MOSFET gate driver. Connect a 0.1µF X7R ceramic capacitor from BOOT to LX. Internal 5.5V LDO charges CBOOT during off-time; UVLO at 2.85V rising / 2.5V falling."+      },+      {+        "number": "16",+        "name": "LX",+        "type": "output",+        "description": "Internal high-side MOSFET switch node output. Connect to the buck inductor and Schottky recirculating diode. Steady-state −0.6V to VCC+0.3V; transient (<10ns) tolerant down to −3V. RDS_ON ≈ 0.2Ω."+      },+      {+        "number": "17",+        "name": "EP",+        "type": "power_in",+        "description": "Exposed thermal pad on the underside of the eTSSOP-16 package. Connect to GND and solder to a copper ground plane with thermal vias for heat dissipation (θJP = 1.617°C/W)."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}