← Commit history

ina200aidr: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·aa9dabf659 · ·parent 66f0650
1 file changed +74−1
page.json+74−1
@@ -33,5 +33,78 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "INA200AIDR",+    "manufacturer": "Texas Instruments",+    "package": "SOIC-8",+    "pin_count": 8,+    "category": "Current-Sensing Amplifiers",+    "parts": {+      "symbol": "ina200aidr.kicad_sym",+      "footprint": "ina200aidr.kicad_mod",+      "model_3d": "ina200aidr-etched.glb",+      "model_3d_plain": "ina200aidr.glb",+      "model_3d_step": "ina200aidr-etched.step",+      "model_3d_step_plain": "ina200aidr.step",+      "lbr": "ina200aidr.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "VS",+        "type": "power_in",+        "description": "Analog power supply input, 2.7 V to 18 V. Quiescent current up to 1800 uA (max). Bypass with a 0.1 uF ceramic capacitor close to the pin."+      },+      {+        "number": "2",+        "name": "OUT",+        "type": "output",+        "description": "Analog voltage output proportional to the shunt voltage times the fixed gain (20 V/V for INA200A). Output can swing rail-to-rail within specified swing limits; drives loads down to the specified minimum resistance."+      },+      {+        "number": "3",+        "name": "CMPIN",+        "type": "input",+        "description": "Non-inverting comparator input. Typically driven by a resistor divider from OUT to set the current trip threshold against the internal 0.6 V reference."+      },+      {+        "number": "4",+        "name": "GND",+        "type": "power_in",+        "description": "Device ground reference for the current-shunt monitor amplifier and the comparator/reference block."+      },+      {+        "number": "5",+        "name": "RESET",+        "type": "input",+        "description": "Active-low comparator latch reset input. Tie low (or leave floating) to run the comparator in transparent (non-latched) mode; drive high to enable latching of the comparator output after a trip event."+      },+      {+        "number": "6",+        "name": "CMPOUT",+        "type": "output",+        "description": "Open-drain comparator output. Pulls low when the CMPIN voltage exceeds the 0.6 V internal reference (over-current alert). Requires an external pull-up resistor to the desired logic rail."+      },+      {+        "number": "7",+        "name": "VIN-",+        "type": "input",+        "description": "Inverting current-shunt monitor input. Connect to the low-side (load-side) terminal of the external sense resistor. Common-mode range -16 V to +80 V independent of VS."+      },+      {+        "number": "8",+        "name": "VIN+",+        "type": "input",+        "description": "Non-inverting current-shunt monitor input. Connect to the high-side (bus-side) terminal of the external sense resistor. Common-mode range -16 V to +80 V independent of VS."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}