← Commit history
README.mdadded+69@@ -0,0 +1,69 @@+# IL34118DWT++**IKSEMICON** · Audio Interface ICs · SOP-28-300mil++IL34118DWT from IKSEMICON, in a SOP-28-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | FO | output | Filter buffer output. Low-output-impedance (<50 Ω) output of the internal filter buffer used with external components to form a high-pass (60/120 Hz hum reject), low-pass, or band-pass filter in the receive path. |+| 2 | FI | input | Filter buffer input. High-impedance (>1.0 MΩ) input to the internal filter buffer; external RC network between FI and FO sets the filter response. |+| 3 | CD | input | Chip Disable. When asserted, powers down the entire circuit to conserve power (useful for long telephone loops where loop current is at a minimum). |+| 4 | VCC | power_in | Positive supply voltage, 3.0 V to 6.5 V. Typical line-powered operation draws ~5.0 mA. |+| 5 | HTO+ | output | Hybrid amplifier 1 non-inverting output. Drives the coupling transformer through the balancing network Zbal; gain set by external resistors -RHF/RHI. Output current capability ≥5 mA (typ 8 mA limit). |+| 6 | HTO- | output | Hybrid amplifier 2 output (fixed internal gain of -1.0). Second of the two hybrid amplifiers used to form the two-to-four wire converter for the telephone line interface. |+| 7 | HTI | input | Hybrid amplifier inverting input. Bias current typically 30 nA out of the pin; open-loop gain ~80 dB, gain-bandwidth ~1.0 MHz. |+| 8 | TXO | output | Transmit attenuator output. Drives the transmit signal path toward the hybrid; complements RXO in half-duplex operation. |+| 9 | TXI | input | Transmit attenuator input. Nominal 10 kΩ input impedance; recommended input signal ≤350 mVrms (990 mVp-p) to prevent distortion. |+| 10 | MCO | output | Microphone amplifier output. Output impedance <10 Ω until current limit (~1.5 mA). Gain set by RMF/RMI external resistors between MCI and MCO. |+| 11 | MCI | input | Microphone amplifier inverting input. Non-inverting input is internally tied to VB. Input bias current typically 40 nA out of the pin. |+| 12 | MUT | input | Mute control input. When activated, reduces microphone amplifier gain to -39 dB by shorting the output to the inverting input (with RMI = 5.1 kΩ). Threshold ~1.5 V; must be kept between GND and VCC; tie to GND if unused. |+| 13 | VLC | input | Volume control input, sensed as a voltage with respect to VB. Adjusts the receive attenuator gain; -46 dB when VLC = VB and increasing toward +6.0 dB as VLC is reduced. Bias current typically 60 nA out of the pin. |+| 14 | CT | passive | Attenuator control timing capacitor. External CT (typ 5.0 μF) with RT (typ 120 kΩ) to VB sets the transmit/receive/idle switching time constants. Voltage at CT (relative to VB) directly monitors the circuit's mode. |+| 15 | VB | power_out | Internal analog reference/bias voltage (mid-supply). Serves as the AC ground reference for the attenuators, hybrid, microphone amplifier, and level detectors. |+| 16 | CPT | passive | Transmit background noise monitor capacitor. External capacitor stores a DC voltage representing the transmit-path noise level; slow rise time (external RC), fast decay. Should match CPR value within ±10%. |+| 17 | TLI2 | input | Transmit level detector 2 input. Senses the microphone amplifier output signal for the transmit background noise / speech detection path. |+| 18 | TLO2 | output | Transmit level detector 2 output. Charges an external capacitor (typ 2.0 μF) through a diode and 350 Ω limiting resistor to form a DC representation of the input AC signal level. |+| 19 | RLO2 | output | Receive level detector 2 output. Charges an external capacitor (typ 2.0 μF) to represent the receive-side (speaker) signal level for the attenuator control block. |+| 20 | RLI2 | input | Receive level detector 2 input. Senses the receive-side signal (typically the speaker amplifier output) for background noise / speech detection. |+| 21 | RXI | input | Receive attenuator input. Nominal 10 kΩ input impedance; recommended input signal ≤350 mVrms (990 mVp-p) to prevent distortion. Also feeds the dial tone detector comparator. |+| 22 | RXO | output | Receive attenuator output. Drives the receive signal path toward the speaker amplifier; complementary in gain to TXO. |+| 23 | TLI1 | input | Transmit level detector 1 input. Senses the hybrid output (Tip/Ring side) signal level for the transmit control path. |+| 24 | TLO1 | output | Transmit level detector 1 output. Charges an external capacitor (typ 2.0 μF) through a diode and 350 Ω limiting resistor to represent the TLI1 input AC signal level. |+| 25 | RLO1 | output | Receive level detector 1 output. Feeds a comparator whose output goes to the attenuator control block; also feeds the receive background noise monitor. |+| 26 | RLI1 | input | Receive level detector 1 input. Sees the same signal as at Tip/Ring for receive-side level detection. |+| 27 | CPR | passive | Receive background noise monitor capacitor. External capacitor stores a DC voltage representing receive-path noise level; charge/discharge sets response time to background noise variations (~4.7 s typical). Should match CPT within ±10%. |+| 28 | GND | power_in | Ground / negative supply return. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | IKSEMICON |+| Package | SOP-28-300mil |+| Category | Interface |+| Pins | 28 |++## Ordering variants++- `IL34118DWTDWT`+- `IL34118DWTDW`+- `IL34118DWTN`++## CAD (KiCad official)++- Symbol: `IL34118DWT`+- Footprint: `Package_SO:SOP-28_8.4x18.16mm_P1.27mm`+- 3D model: SOP-28-300mil (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [IKSEMICON datasheet](docs/il34118dwt-datasheet.pdf) (14 pp, sha256 `b3cd47de9884e9d2`, retrieved 2026-08-17, tier: lcsc)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/il34118dwt-datasheet.pdf)
page.jsonadded+34@@ -0,0 +1,34 @@+{+ "slug": "il34118dwt",+ "version": "0.1.0",+ "type": "component",+ "description": "IKSEMICON Audio Interface ICs, SOP-28-300mil. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "interface",+ "il34118dwt"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "il34118dwt.kicad_sym",+ "il34118dwt.kicad_mod",+ "il34118dwt.glb",+ "il34118dwt.step",+ "il34118dwt.lbr",+ "docs/hero.png",+ "docs/il34118dwt-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ],+ "visibility": "public",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}