← Commit history

hx6610s: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·4c7907ea6c · ·parent d791157
1 file changed +74−1
page.json+74−1
@@ -33,5 +33,78 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "HX6610S",+    "manufacturer": "HX hengjiaxing",+    "package": "ESOP-8",+    "pin_count": 8,+    "category": "Battery Management",+    "parts": {+      "symbol": "hx6610s.kicad_sym",+      "footprint": "hx6610s.kicad_mod",+      "model_3d": "hx6610s-etched.glb",+      "model_3d_plain": "hx6610s.glb",+      "model_3d_step": "hx6610s-etched.step",+      "model_3d_step_plain": "hx6610s.step",+      "lbr": "hx6610s.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "BAT",+        "type": "power_out",+        "description": "Battery positive terminal. Connects to the Li-ion cell's + terminal; delivers the trickle/CC/CV charge current from the internal PMOSFET. Float voltage is typically 4.22V (Vfloat range 4.18-4.26V). A 1uF bypass capacitor to GND should be placed close to this pin."+      },+      {+        "number": "2",+        "name": "Vprog",+        "type": "input",+        "description": "Float-voltage programming pin. Left open (no R2) gives the default Vfloat = 4.22V. A resistor from Vprog to GND raises the float voltage (R = 2.20*265000/(Vprog-4.20)); a resistor from Vprog to BAT lowers it below 4.2V (R//265000 = (Vprog-2.2)*291500/2.2). Place R2 close to the pin to minimize Vfloat disturbance."+      },+      {+        "number": "3",+        "name": "GND",+        "type": "power_in",+        "description": "Device ground / negative supply reference. All electrical parameters are referenced to this pin (0 V)."+      },+      {+        "number": "4",+        "name": "CT",+        "type": "input",+        "description": "Full-charge shutdown delay setting pin. A capacitor from CT to GND programs the delay before terminating charge / switching the indicator LED, per C = (1.5e-6 * T)/2.2 (e.g. 30 ms delay ≈ 20.5 nF). May be left unconnected when no delay/indicator transition is required."+      },+      {+        "number": "5",+        "name": "Iprog",+        "type": "input",+        "description": "Charge-current programming pin (PROG). A 1% resistor from Iprog to GND sets the constant-current charge current per Ibat = 1200/R (e.g. 6 kΩ ⇒ 200 mA; max programmable ≈ 1 A). Pin voltage is ~0.1 V in trickle mode and ~1 V at full current."+      },+      {+        "number": "6",+        "name": "CHRG",+        "type": "output",+        "description": "Open-drain charge-status indicator. Pulled low (LED on) while the chip is actively charging; high-impedance (LED off) when charging is complete, input is removed, or battery is shorted/reversed. Tie to VDD through an LED+resistor, or to GND if unused."+      },+      {+        "number": "7",+        "name": "STDBY",+        "type": "output",+        "description": "Open-drain standby/full-charge indicator. Pulled low (LED on) when charging is finished or no battery is present; high-impedance while charging is in progress or under fault (short/reverse). Tie to VDD through an LED+resistor, or to GND if unused."+      },+      {+        "number": "8",+        "name": "VDD",+        "type": "power_in",+        "description": "Positive supply input from USB or AC adapter. Operating range 4.5-6 V (absolute max 7 V); OVP trips at 6.2 V and charging stops. UVLO threshold ≈ 3.7 V (200 mV hysteresis). Place a 1 uF bypass capacitor to GND close to this pin."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}