← Commit history

hx24lc128bdrg: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·dca9698ece · ·parent babac1d
1 file changed +74−1
page.json+74−1
@@ -33,5 +33,78 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "HX24LC128BDRG",+    "manufacturer": "HANSCHIP semiconductor",+    "package": "SOP-8",+    "pin_count": 8,+    "category": "EEPROM",+    "parts": {+      "symbol": "hx24lc128bdrg.kicad_sym",+      "footprint": "hx24lc128bdrg.kicad_mod",+      "model_3d": "hx24lc128bdrg-etched.glb",+      "model_3d_plain": "hx24lc128bdrg.glb",+      "model_3d_step": "hx24lc128bdrg-etched.step",+      "model_3d_step_plain": "hx24lc128bdrg.step",+      "lbr": "hx24lc128bdrg.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "A0",+        "type": "input",+        "description": "Device address input bit 0. Hardwire to VCC or GND to set one of the LSBs of the I2C slave address, allowing up to 4 (with A1) devices on the same bus. Internally biased low if left floating and board VCC-plane capacitive coupling is <3 pF; otherwise tie to GND."+      },+      {+        "number": "2",+        "name": "A1",+        "type": "input",+        "description": "Device address input bit 1. Hardwire to VCC or GND to select the device's I2C slave address. Internally biased low if left floating (with the <3 pF coupling caveat); otherwise tie to GND."+      },+      {+        "number": "3",+        "name": "NC",+        "type": "unconnected",+        "description": "No connect. Leave unconnected. (Note: the block diagram references an A2 address input, but on the 8-pin package this position is documented as NC.)"+      },+      {+        "number": "4",+        "name": "GND",+        "type": "power_in",+        "description": "Ground reference for the device."+      },+      {+        "number": "5",+        "name": "SDA",+        "type": "bidirectional",+        "description": "Serial data. Bidirectional, open-drain - requires an external pull-up resistor. Can be wire-ORed with other open-drain/open-collector devices on the two-wire bus."+      },+      {+        "number": "6",+        "name": "SCL",+        "type": "input",+        "description": "Serial clock input. Positive edge clocks data into the EEPROM and negative edge clocks data out. Max 400 kHz at 1.8/2.7/3.3 V and 1 MHz at 5 V."+      },+      {+        "number": "7",+        "name": "WP",+        "type": "input",+        "description": "Write protect input. Tied to GND allows normal read/write; tied to VCC inhibits all writes to the full memory array. Internally biased low if left floating (with the <3 pF coupling caveat); otherwise tie to GND."+      },+      {+        "number": "8",+        "name": "VCC",+        "type": "power_in",+        "description": "Positive supply, 1.8 V to 5.5 V. ICC ≈ 0.4 mA (read) / 2.0 mA (write) at 5 V, 400 kHz; standby current ISB ≈ 3 µA at 5.5 V."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}