← Commit history
ht24c256arz: restore the component block (pinout + model declarations) from this page's own README and symbol
1 file changed
+74−1
page.json+74−1@@ -31,5 +31,78 @@ "author": { "name": "Ray", "email": "[email protected]"+ },+ "component": {+ "mpn": "HT24C256ARZ",+ "manufacturer": "HTCSEMI",+ "package": "SOP-8",+ "pin_count": 8,+ "category": "EEPROM",+ "parts": {+ "symbol": "ht24c256arz.kicad_sym",+ "footprint": "ht24c256arz.kicad_mod",+ "model_3d": "ht24c256arz-etched.glb",+ "model_3d_plain": "ht24c256arz.glb",+ "model_3d_step": "ht24c256arz-etched.step",+ "model_3d_step_plain": "ht24c256arz.step",+ "lbr": "ht24c256arz.lbr"+ },+ "pins": [+ {+ "number": "1",+ "name": "A0",+ "type": "input",+ "description": "Device address input bit 0. Hard-wired to VSS or VCC to set the least significant bit of the I2C slave address; if left floating it is internally read as VSS (low). Up to eight HT24C256A devices can share one 2-wire bus by using unique A0/A1/A2 combinations."+ },+ {+ "number": "2",+ "name": "A1",+ "type": "input",+ "description": "Device address input bit 1. Hard-wired to VSS or VCC to set the second I2C slave address bit; if left floating it is internally read as VSS (low)."+ },+ {+ "number": "3",+ "name": "A2",+ "type": "input",+ "description": "Device address input bit 2. Hard-wired to VSS or VCC to set the most significant of the three slave address bits; if left floating it is internally read as VSS (low)."+ },+ {+ "number": "4",+ "name": "VSS",+ "type": "power_in",+ "description": "Negative power supply / ground reference (0V)."+ },+ {+ "number": "5",+ "name": "SDA",+ "type": "bidirectional",+ "description": "Serial data input/output for the 2-wire (I2C) interface. Open-drain output that requires an external pull-up resistor to VCC; may be wired-OR with other open-drain devices on the bus. Input high VIH = 0.7*VCC min, input low VIL = 0.3*VCC max; VOL = 0.4V max at IOL = 2.1mA (VCC = 2.4V)."+ },+ {+ "number": "6",+ "name": "SCL",+ "type": "input",+ "description": "Serial clock input for the 2-wire (I2C) interface. Data is clocked into the EEPROM on the positive edge and clocked out on the negative edge. Maximum clock frequency is 400kHz at VCC = 1.8V-5.0V and 1MHz at VCC = 2.5V-5.0V."+ },+ {+ "number": "7",+ "name": "WP",+ "type": "input",+ "description": "Write protect input. When tied to VCC, the entire 256K memory array is write-protected (read-only). When tied to VSS or left floating, normal read/write operations are permitted."+ },+ {+ "number": "8",+ "name": "VCC",+ "type": "power_in",+ "description": "Positive power supply, 1.8V to 5.5V over the -40°C to +85°C operating range. Operating current is 2mA max (read) / 5mA max (write) at 5V, 400kHz; standby current is 3μA max at 5V."+ }+ ],+ "provenance": {+ "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ } }-}+}