← Commit history

ht2459artz: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·3d75c2347f · ·parent 1fec9e6
1 file changed +62−1
page.json+62−1
@@ -33,5 +33,66 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "HT2459ARTZ",+    "manufacturer": "HTCSEMI",+    "package": "SOT-23-6",+    "pin_count": 6,+    "category": "DC-DC Converters",+    "parts": {+      "symbol": "ht2459artz.kicad_sym",+      "footprint": "ht2459artz.kicad_mod",+      "model_3d": "ht2459artz-etched.glb",+      "model_3d_plain": "ht2459artz.glb",+      "model_3d_step": "ht2459artz-etched.step",+      "model_3d_step_plain": "ht2459artz.step",+      "lbr": "ht2459artz.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "BST",+        "type": "passive",+        "description": "Bootstrap. Connect a capacitor (0.1µF-1µF) between SW and BST to form a floating supply across the power switch driver, driving the high-side MOSFET gate above the supply voltage. An optional external BST diode (e.g. 1N4148) from VOUT to BST enhances efficiency at high duty cycles."+      },+      {+        "number": "2",+        "name": "GND",+        "type": "power_in",+        "description": "Ground. Voltage reference for the regulated output voltage. Requires special layout considerations - isolate this node from the D1-to-C1 ground path to prevent switching current spikes from being induced into the analog ground."+      },+      {+        "number": "3",+        "name": "FB",+        "type": "input",+        "description": "Feedback. Sets the output voltage via an external resistor divider from VOUT to GND, regulated to the internal 0.812V (typ) bandgap reference. The frequency foldback comparator lowers the oscillator frequency (to ~150kHz) when FB is below 250mV to prevent current-limit runaway during a short-circuit fault."+      },+      {+        "number": "4",+        "name": "EN",+        "type": "input",+        "description": "Enable (On/Off). Pull EN above 1.35V (typ rising threshold) to turn the device ON; falling threshold is 1.17V (typ) with 180mV hysteresis. For automatic enable, connect to VIN through a 100kΩ resistor. Input current is ~3.1µA at VEN=2V."+      },+      {+        "number": "5",+        "name": "IN",+        "type": "power_in",+        "description": "Supply Voltage input. The HT2459 operates from a 4.5V-to-60V unregulated input. Requires an input ceramic capacitor (typ 4.7µF, X5R/X7R) close to the pin to prevent large voltage spikes from appearing at the input."+      },+      {+        "number": "6",+        "name": "SW",+        "type": "output",+        "description": "Switch Output. Drain of the internal high-side power MOSFET (RDS(ON) ≈ 0.5Ω typ). Connect to the external inductor and Schottky rectifier diode. Absolute rating: -0.3V to VIN+0.3V."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}