component
HR911130A
Public Made by Adomby adom
HANRUN(Zhongshan HanRun Elec) Modular/Ethernet Connector (RJ45) Jacks With Magnetics, Through Hole. KiCad symbol, footprint and 3D as used on Adom boards; pin functions from the manufacturer datasheet.
← Commit history
Publish 0.1.1
8 files changed
+612−86
README.md+20−18@@ -4,28 +4,28 @@ **HANRUN(Zhongshan HanRun Elec)** · Modular/Ethernet Connector (RJ45) Jacks With Magnetics · Through Hole -HR911130A from HANRUN(Zhongshan HanRun Elec), in a Through Hole. Symbol, footprint and 3D model are the ones used on Adom board designs (3D model: Adom-generated 3D model built from the datasheet dimensions (simplified; CC-BY-SA 4.0); no vendor CAD is redistributed). Pin functions are extracted from the manufacturer datasheet with page references. **Staged for validation: see the open items in the verification log above.**+HR911130A from HANRUN(Zhongshan HanRun Elec), in a Through Hole. Symbol, footprint and 3D model are the ones used on Adom board designs (3D model: Adom-generated 3D model built from the datasheet dimensions (simplified; CC-BY-SA 4.0); no vendor CAD is redistributed). Pin functions are extracted from the manufacturer datasheet with page references. ## Pinout | Pin | Name | Type | Function | |---|---|---|---|-| 1 | P1 | passive | Chip-side pad P1. Internally tied through the Bob-Smith termination network (4x75Ω common node) to the 1000pF/2kV bypass capacitor returning to P10. Typically connected to the chassis/termination ground on the PHY side. [datasheet p.1] |-| 2 | MDI0+ | passive | Chip-side pin P2 — MDI pair 0 positive (BI_DA+). Connects to the center-tapped primary of the first 1CT:1CT transformer; routes to UTP pin J1 (A+). Terminate to the PHY's TX/RX pair 0 positive. [datasheet p.1] |-| 3 | MDI0- | passive | Chip-side pin P3 — MDI pair 0 negative (BI_DA-). Second lead of pair 0 primary; routes to UTP pin J2 (A-). [datasheet p.1] |-| 4 | MDI1+ | passive | Chip-side pin P4 — MDI pair 1 positive (BI_DB+). Primary lead of the second 1CT:1CT transformer; routes to UTP pin J3 (B+). [datasheet p.1] |-| 5 | MDI2+ | passive | Chip-side pin P5 — MDI pair 2 positive (BI_DC+). Primary lead of the third 1CT:1CT transformer; routes to UTP pin J5 (C-). Note: UTP pin assignment follows the datasheet schematic. [datasheet p.1] |-| 6 | MDI2- | passive | Chip-side pin P6 — MDI pair 2 negative (BI_DC-). Second primary lead of pair 2 transformer; routes to UTP pin J6 (B-). [datasheet p.1] |-| 7 | MDI1- | passive | Chip-side pin P7 — MDI pair 1 negative (BI_DB-). Second primary lead of pair 1 transformer; routes to UTP pin J4 (C+). [datasheet p.1] |-| 8 | MDI3+ | passive | Chip-side pin P8 — MDI pair 3 positive (BI_DD+). Primary lead of the fourth 1CT:1CT transformer; routes to UTP pin J7 (D+). [datasheet p.1] |-| 9 | MDI3- | passive | Chip-side pin P9 — MDI pair 3 negative (BI_DD-). Second primary lead of pair 3 transformer; routes to UTP pin J8 (D-). [datasheet p.1] |-| 10 | P10 | passive | Chip-side pad P10 — Bob-Smith termination return. Connects to the 1000pF/2kV bypass capacitor that ties the common node of the 4x75Ω termination network back to chassis/earth ground. [datasheet p.1] |-| 11 | 11 | passive | Green LED anode (left LED). Forward voltage 1.8V (min) / 2.8V (max), 20mA, 568nm wavelength. Drive via a current-limiting resistor from the PHY's LED output or Vcc with the cathode (pin 12) sinking to the PHY. [datasheet p.1] |-| 12 | 12 | passive | Green LED cathode (left LED). Pair with pin 11; typically driven by an open-drain PHY LED output. [datasheet p.1] |-| 13 | 13 | passive | Yellow LED cathode (right LED). Pair with pin 14; typically driven by an open-drain PHY LED output. [datasheet p.1] |-| 14 | 14 | passive | Yellow LED anode (right LED). Forward voltage 1.8V (min) / 2.8V (max), 20mA, 585nm wavelength. Drive via a current-limiting resistor from the PHY's LED output or Vcc. [datasheet p.1] |-| S1 | SHIELD | passive | Shield / mounting contact (mechanical); connect per the board design. [from symbol] |-| S2 | SHIELD | passive | Shield / mounting contact (mechanical); connect per the board design. [from symbol] |+| 1 | P1 | passive | Common centre tap of the four chip-side transformer windings (the drawing labels it P1 only). [datasheet p.1] |+| 2 | MDI0+ | passive | MDI 0+ (P2): chip-side winding of a 1CT:1CT transformer; reaches jack contact J1 (A+) through the common-mode choke. [datasheet p.1] |+| 3 | MDI0- | passive | MDI 0- (P3): chip-side winding of a 1CT:1CT transformer; reaches jack contact J2 (A-) through the common-mode choke. [datasheet p.1] |+| 4 | MDI1+ | passive | MDI 1+ (P4): chip-side winding of a 1CT:1CT transformer; reaches jack contact J3 (B+) through the common-mode choke. [datasheet p.1] |+| 5 | MDI2+ | passive | MDI 2+ (P5): chip-side winding of a 1CT:1CT transformer; reaches jack contact J4 (C+) through the common-mode choke. [datasheet p.1] |+| 6 | MDI2- | passive | MDI 2- (P6): chip-side winding of a 1CT:1CT transformer; reaches jack contact J5 (C-) through the common-mode choke. [datasheet p.1] |+| 7 | MDI1- | passive | MDI 1- (P7): chip-side winding of a 1CT:1CT transformer; reaches jack contact J6 (B-) through the common-mode choke. [datasheet p.1] |+| 8 | MDI3+ | passive | MDI 3+ (P8): chip-side winding of a 1CT:1CT transformer; reaches jack contact J7 (D+) through the common-mode choke. [datasheet p.1] |+| 9 | MDI3- | passive | MDI 3- (P9): chip-side winding of a 1CT:1CT transformer; reaches jack contact J8 (D-) through the common-mode choke. [datasheet p.1] |+| 10 | P10 | passive | Termination return: each cable-side centre tap goes through 75 ohms (4 x 75 ohms) to a common node, which reaches P10 through a 1000 pF 2 kV capacitor. [datasheet p.1] |+| 11 | 11 | passive | Green LED anode; the cathode is pin 12 (schematic p.1). Left LED seen from the front; 568 nm, forward voltage 1.8 V min / 2.8 V max at 20 mA. [datasheet p.2] |+| 12 | 12 | passive | Green LED cathode; the anode is pin 11. [datasheet p.1] |+| 13 | 13 | passive | Yellow LED cathode; the anode is pin 14. [datasheet p.1] |+| 14 | 14 | passive | Yellow LED anode; the cathode is pin 13 (schematic p.1). Right LED seen from the front; 585 nm, forward voltage 1.8 V min / 2.8 V max at 20 mA. [datasheet p.2] |+| S1 | SHIELD | passive | Shield pin in one of the two 1.63 mm plated holes of the recommended PCB layout (the drawing gives it no name). [datasheet p.3] |+| S2 | SHIELD | passive | Shield pin in one of the two 1.63 mm plated holes of the recommended PCB layout (the drawing gives it no name). [datasheet p.3] | ## Key specifications @@ -36,6 +36,8 @@ HR911130A from HANRUN(Zhongshan HanRun Elec), in a Through Hole. Symbol, footpri | Category | Connectors | | Pins | 16 | | LCSC | C54408 |+| Mouser | Not carried (searched 2026-10-27) |+| DigiKey | Not carried (searched 2026-10-27) | | Distributor summary (LCSC listing, not datasheet) | 0℃~+70℃ 1 Gold Non-PoE Phosphor bronze RJ45 Jack Right Angle Shielded With Cross Pin With LED 插件 Ethernet Connectors / Modular Connectors (RJ45 RJ11) ROHS | ## CAD@@ -48,7 +50,7 @@ HR911130A from HANRUN(Zhongshan HanRun Elec), in a Through Hole. Symbol, footpri ## Provenance -- **Datasheet:** [HANRUN(Zhongshan HanRun Elec) datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588887489490112512) (sha256 `06b3f922bf514722`, retrieved 2026-10-09, tier: lcsc)+- **Datasheet:** [HanRun HR911130A datasheet](https://hrdzcn.oss-cn-beijing.aliyuncs.com/202601/ab534667d942f65.pdf) (Rev. B (no date printed; PDF created 2020-02-28), sha256 `e9532cda421d20b6`, retrieved 2026-10-27, tier: mfr) - **CAD:** Footprint and symbol as used on Adom board designs; 3D model: Adom-generated 3D model built from the datasheet dimensions (simplified; CC-BY-SA 4.0); no vendor CAD is redistributed. - **Pins:** KiCad symbol from the source board + adom-ds2sf datasheet extraction (claude-opus-4-7).
docs/hr911130a-datasheet.pdf⋯ 1 unchanged line ⋯
hr911130a-hero.glbadded⋯ 1 unchanged line ⋯
hr911130a-hero.overlay.jsonadded+441@@ -0,0 +1,441 @@+{+ "spec": "adom-hero 1.4",+ "mpn": "HR911130A",+ "kind": "component + footprint reference art",+ "board_use": false,+ "plane_z_mm": -0.02,+ "units": "metre",+ "upAxis": "Z",+ "layers": {+ "pad_outlines": {+ "material": "Footprint pads - teal dashed outlines - 50 percent opacity",+ "rgba": [+ 0.0,+ 0.902,+ 0.863,+ 0.5+ ],+ "pads": 16,+ "span_mm": 17.935,+ "dash_mm": 0.4484,+ "gap_mm": 0.269,+ "pad_stroke_mm": 0.09+ },+ "silkscreen": {+ "material": "Silkscreen reference lines - 30 percent opacity",+ "rgba": [+ 0.92,+ 0.96,+ 1.0,+ 0.3+ ],+ "footprint_items": 6,+ "pin1": {+ "source": "added dot (AI)",+ "pad": "1",+ "center_mm": [+ 6.927,+ 8.89+ ],+ "r_mm": 0.308+ }+ },+ "signal_names": {+ "material": "Signal names - 50 percent opacity",+ "rgba": [+ 0.92,+ 0.96,+ 1.0,+ 0.5+ ],+ "font": "DejaVu Sans Mono",+ "labels": 16,+ "sides": "top + mirrored underside (single-sided)",+ "fallback_to_pad_number": 4+ }+ },+ "align": {+ "ok": true,+ "centre_offset_mm": 0.008,+ "tolerance_mm": 1.435,+ "orientation_flipped": false,+ "contacts_bbox_mm": [+ -7.895,+ 7.895,+ -9.09,+ 5.15+ ],+ "pads_bbox_mm": [+ -8.968,+ 8.968,+ -9.589,+ 5.665+ ],+ "seating_z_mm": -3.051+ },+ "sources": {+ "glb": "hr911130a.glb",+ "glb_sha256": "98a52eb5270de72d334c85dffc5bdd1f45c4f6311f6058536dbaa2e15dbfed70",+ "footprint": "hr911130a.kicad_mod",+ "footprint_sha256": "ef6edeb2ef490dca592e62b2cc5fe77fba508d7a41e1461db9b74fa12e629476",+ "pins": "page.json component.pins",+ "pins_sha256": "674c3c3037952e7545b31647cc373a9d534232671fa4c01546ab30547c657391"+ },+ "generator": "adom-wiki 1.8.0 (component_hero)",+ "labels": [+ {+ "pad": "1",+ "text": "P1",+ "x": 5.72,+ "y": 9.739,+ "align": "right",+ "vertical": true,+ "h": 0.6+ },+ {+ "pad": "2",+ "text": "MDI0+",+ "x": 4.44,+ "y": 7.199,+ "align": "right",+ "vertical": true,+ "h": 0.6+ },+ {+ "pad": "3",+ "text": "MDI0-",+ "x": 3.18,+ "y": 9.739,+ "align": "right",+ "vertical": true,+ "h": 0.6+ },+ {+ "pad": "4",+ "text": "MDI1+",+ "x": 1.9,+ "y": 7.199,+ "align": "right",+ "vertical": true,+ "h": 0.6+ },+ {+ "pad": "5",+ "text": "MDI2+",+ "x": 0.64,+ "y": 9.739,+ "align": "right",+ "vertical": true,+ "h": 0.6+ },+ {+ "pad": "6",+ "text": "MDI2-",+ "x": -0.64,+ "y": 7.199,+ "align": "right",+ "vertical": true,+ "h": 0.6+ },+ {+ "pad": "7",+ "text": "MDI1-",+ "x": -1.9,+ "y": 9.739,+ "align": "right",+ "vertical": true,+ "h": 0.6+ },+ {+ "pad": "8",+ "text": "MDI3+",+ "x": -3.18,+ "y": 7.199,+ "align": "right",+ "vertical": true,+ "h": 0.6+ },+ {+ "pad": "9",+ "text": "MDI3-",+ "x": -4.44,+ "y": 9.739,+ "align": "right",+ "vertical": true,+ "h": 0.6+ },+ {+ "pad": "10",+ "text": "P10",+ "x": -6.569,+ "y": 6.35,+ "align": "right",+ "vertical": false,+ "h": 0.6+ },+ {+ "pad": "11",+ "text": "11",+ "x": 6.625,+ "y": -5.815,+ "align": "left",+ "vertical": true,+ "h": 0.6+ },+ {+ "pad": "12",+ "text": "12",+ "x": 4.085,+ "y": -5.815,+ "align": "left",+ "vertical": true,+ "h": 0.6+ },+ {+ "pad": "13",+ "text": "13",+ "x": -4.085,+ "y": -5.815,+ "align": "left",+ "vertical": true,+ "h": 0.6+ },+ {+ "pad": "14",+ "text": "14",+ "x": -6.625,+ "y": -5.815,+ "align": "left",+ "vertical": true,+ "h": 0.6+ },+ {+ "pad": "S1",+ "text": "SHIELD",+ "x": 9.118,+ "y": 3.05,+ "align": "left",+ "vertical": false,+ "h": 0.6+ },+ {+ "pad": "S2",+ "text": "SHIELD",+ "x": -9.118,+ "y": 3.05,+ "align": "right",+ "vertical": false,+ "h": 0.6+ }+ ],+ "pads": [+ {+ "number": "1",+ "shape": "rect",+ "center_mm": [+ 5.72,+ 8.89+ ],+ "size_mm": [+ 1.398,+ 1.398+ ],+ "rot": 0.0+ },+ {+ "number": "2",+ "shape": "circle",+ "center_mm": [+ 4.44,+ 6.35+ ],+ "size_mm": [+ 1.398,+ 1.398+ ],+ "rot": 0.0+ },+ {+ "number": "3",+ "shape": "circle",+ "center_mm": [+ 3.18,+ 8.89+ ],+ "size_mm": [+ 1.398,+ 1.398+ ],+ "rot": 0.0+ },+ {+ "number": "4",+ "shape": "circle",+ "center_mm": [+ 1.9,+ 6.35+ ],+ "size_mm": [+ 1.398,+ 1.398+ ],+ "rot": 0.0+ },+ {+ "number": "5",+ "shape": "circle",+ "center_mm": [+ 0.64,+ 8.89+ ],+ "size_mm": [+ 1.398,+ 1.398+ ],+ "rot": 0.0+ },+ {+ "number": "6",+ "shape": "circle",+ "center_mm": [+ -0.64,+ 6.35+ ],+ "size_mm": [+ 1.398,+ 1.398+ ],+ "rot": 0.0+ },+ {+ "number": "7",+ "shape": "circle",+ "center_mm": [+ -1.9,+ 8.89+ ],+ "size_mm": [+ 1.398,+ 1.398+ ],+ "rot": 0.0+ },+ {+ "number": "8",+ "shape": "circle",+ "center_mm": [+ -3.18,+ 6.35+ ],+ "size_mm": [+ 1.398,+ 1.398+ ],+ "rot": 0.0+ },+ {+ "number": "9",+ "shape": "circle",+ "center_mm": [+ -4.44,+ 8.89+ ],+ "size_mm": [+ 1.398,+ 1.398+ ],+ "rot": 0.0+ },+ {+ "number": "10",+ "shape": "circle",+ "center_mm": [+ -5.72,+ 6.35+ ],+ "size_mm": [+ 1.398,+ 1.398+ ],+ "rot": 0.0+ },+ {+ "number": "11",+ "shape": "circle",+ "center_mm": [+ 6.625,+ -4.9+ ],+ "size_mm": [+ 1.53,+ 1.53+ ],+ "rot": 0.0+ },+ {+ "number": "12",+ "shape": "circle",+ "center_mm": [+ 4.085,+ -4.9+ ],+ "size_mm": [+ 1.53,+ 1.53+ ],+ "rot": 0.0+ },+ {+ "number": "13",+ "shape": "circle",+ "center_mm": [+ -4.085,+ -4.9+ ],+ "size_mm": [+ 1.53,+ 1.53+ ],+ "rot": 0.0+ },+ {+ "number": "14",+ "shape": "circle",+ "center_mm": [+ -6.625,+ -4.9+ ],+ "size_mm": [+ 1.53,+ 1.53+ ],+ "rot": 0.0+ },+ {+ "number": "S1",+ "shape": "circle",+ "center_mm": [+ 7.745,+ 3.05+ ],+ "size_mm": [+ 2.445,+ 2.445+ ],+ "rot": 0.0+ },+ {+ "number": "S2",+ "shape": "circle",+ "center_mm": [+ -7.745,+ 3.05+ ],+ "size_mm": [+ 2.445,+ 2.445+ ],+ "rot": 0.0+ }+ ]+}
hr911130a.lbr+1−1@@ -169,7 +169,7 @@ <technology name=""> <attribute name="MPN" value="HR911130A" constant="no"/> <attribute name="MANUFACTURER" value="HANRUN(Zhongshan HanRun Elec)" constant="no"/>- <attribute name="DATASHEET" value="https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588887489490112512" constant="no"/>+ <attribute name="DATASHEET" value="https://hrdzcn.oss-cn-beijing.aliyuncs.com/202601/ab534667d942f65.pdf" constant="no"/> <attribute name="ADOM_WIKI" value="https://wiki.adom.inc/adom/hr911130a" constant="no"/> <attribute name="LCSC_PN" value="C54408" constant="no"/> </technology>
package.json+33−34@@ -1,13 +1,12 @@ { "slug": "hr911130a",- "version": "0.1.0",+ "version": "0.1.1", "type": "component", "tags": [ "component", "connectors", "hr911130a",- "board-derived",- "staged-for-validation"+ "board-derived" ], "dependencies": {}, "hero": {@@ -25,8 +24,8 @@ "hr911130a.lbr", "docs/hero.png", "docs/hr911130a-datasheet.pdf",- "viewers/symbol.html",- "viewers/footprint.html"+ "hr911130a-hero.glb",+ "hr911130a-hero.overlay.json" ], "component": { "mpn": "HR911130A",@@ -35,11 +34,11 @@ "pin_count": 16, "category": "Connectors", "subcategory": "Modular/Ethernet Connector (RJ45) Jacks With Magnetics",- "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588887489490112512",+ "datasheet": "https://hrdzcn.oss-cn-beijing.aliyuncs.com/202601/ab534667d942f65.pdf", "parts": { "symbol": "hr911130a.kicad_sym", "footprint": "hr911130a.kicad_mod",- "model_3d": "hr911130a.glb",+ "model_3d": "hr911130a-hero.glb", "model_3d_plain": "hr911130a.glb", "model_3d_step": "hr911130a.step", "model_3d_step_plain": "hr911130a.step",@@ -47,9 +46,9 @@ }, "distributor_links": { "digikey": false,- "digikey_note": "2026-10-09: no exact-MPN listing for HR911130A found via the digikey API.",+ "digikey_note": "Not carried: searched HR911130A on 2026-10-27.", "mouser": false,- "mouser_note": "2026-10-09: no exact-MPN listing for HR911130A found via the mouser API.",+ "mouser_note": "Not carried: searched HR911130A on 2026-10-27.", "lcsc": { "part": "C54408", "url": "https://www.lcsc.com/product-detail/C54408.html"@@ -60,97 +59,97 @@ "number": "1", "name": "P1", "type": "passive",- "description": "Chip-side pad P1. Internally tied through the Bob-Smith termination network (4x75Ω common node) to the 1000pF/2kV bypass capacitor returning to P10. Typically connected to the chassis/termination ground on the PHY side. [datasheet p.1]"+ "description": "Common centre tap of the four chip-side transformer windings (the drawing labels it P1 only). [datasheet p.1]" }, { "number": "2", "name": "MDI0+", "type": "passive",- "description": "Chip-side pin P2 — MDI pair 0 positive (BI_DA+). Connects to the center-tapped primary of the first 1CT:1CT transformer; routes to UTP pin J1 (A+). Terminate to the PHY's TX/RX pair 0 positive. [datasheet p.1]"+ "description": "MDI 0+ (P2): chip-side winding of a 1CT:1CT transformer; reaches jack contact J1 (A+) through the common-mode choke. [datasheet p.1]" }, { "number": "3", "name": "MDI0-", "type": "passive",- "description": "Chip-side pin P3 — MDI pair 0 negative (BI_DA-). Second lead of pair 0 primary; routes to UTP pin J2 (A-). [datasheet p.1]"+ "description": "MDI 0- (P3): chip-side winding of a 1CT:1CT transformer; reaches jack contact J2 (A-) through the common-mode choke. [datasheet p.1]" }, { "number": "4", "name": "MDI1+", "type": "passive",- "description": "Chip-side pin P4 — MDI pair 1 positive (BI_DB+). Primary lead of the second 1CT:1CT transformer; routes to UTP pin J3 (B+). [datasheet p.1]"+ "description": "MDI 1+ (P4): chip-side winding of a 1CT:1CT transformer; reaches jack contact J3 (B+) through the common-mode choke. [datasheet p.1]" }, { "number": "5", "name": "MDI2+", "type": "passive",- "description": "Chip-side pin P5 — MDI pair 2 positive (BI_DC+). Primary lead of the third 1CT:1CT transformer; routes to UTP pin J5 (C-). Note: UTP pin assignment follows the datasheet schematic. [datasheet p.1]"+ "description": "MDI 2+ (P5): chip-side winding of a 1CT:1CT transformer; reaches jack contact J4 (C+) through the common-mode choke. [datasheet p.1]" }, { "number": "6", "name": "MDI2-", "type": "passive",- "description": "Chip-side pin P6 — MDI pair 2 negative (BI_DC-). Second primary lead of pair 2 transformer; routes to UTP pin J6 (B-). [datasheet p.1]"+ "description": "MDI 2- (P6): chip-side winding of a 1CT:1CT transformer; reaches jack contact J5 (C-) through the common-mode choke. [datasheet p.1]" }, { "number": "7", "name": "MDI1-", "type": "passive",- "description": "Chip-side pin P7 — MDI pair 1 negative (BI_DB-). Second primary lead of pair 1 transformer; routes to UTP pin J4 (C+). [datasheet p.1]"+ "description": "MDI 1- (P7): chip-side winding of a 1CT:1CT transformer; reaches jack contact J6 (B-) through the common-mode choke. [datasheet p.1]" }, { "number": "8", "name": "MDI3+", "type": "passive",- "description": "Chip-side pin P8 — MDI pair 3 positive (BI_DD+). Primary lead of the fourth 1CT:1CT transformer; routes to UTP pin J7 (D+). [datasheet p.1]"+ "description": "MDI 3+ (P8): chip-side winding of a 1CT:1CT transformer; reaches jack contact J7 (D+) through the common-mode choke. [datasheet p.1]" }, { "number": "9", "name": "MDI3-", "type": "passive",- "description": "Chip-side pin P9 — MDI pair 3 negative (BI_DD-). Second primary lead of pair 3 transformer; routes to UTP pin J8 (D-). [datasheet p.1]"+ "description": "MDI 3- (P9): chip-side winding of a 1CT:1CT transformer; reaches jack contact J8 (D-) through the common-mode choke. [datasheet p.1]" }, { "number": "10", "name": "P10", "type": "passive",- "description": "Chip-side pad P10 — Bob-Smith termination return. Connects to the 1000pF/2kV bypass capacitor that ties the common node of the 4x75Ω termination network back to chassis/earth ground. [datasheet p.1]"+ "description": "Termination return: each cable-side centre tap goes through 75 ohms (4 x 75 ohms) to a common node, which reaches P10 through a 1000 pF 2 kV capacitor. [datasheet p.1]" }, { "number": "11", "name": "11", "type": "passive",- "description": "Green LED anode (left LED). Forward voltage 1.8V (min) / 2.8V (max), 20mA, 568nm wavelength. Drive via a current-limiting resistor from the PHY's LED output or Vcc with the cathode (pin 12) sinking to the PHY. [datasheet p.1]"+ "description": "Green LED anode; the cathode is pin 12 (schematic p.1). Left LED seen from the front; 568 nm, forward voltage 1.8 V min / 2.8 V max at 20 mA. [datasheet p.2]" }, { "number": "12", "name": "12", "type": "passive",- "description": "Green LED cathode (left LED). Pair with pin 11; typically driven by an open-drain PHY LED output. [datasheet p.1]"+ "description": "Green LED cathode; the anode is pin 11. [datasheet p.1]" }, { "number": "13", "name": "13", "type": "passive",- "description": "Yellow LED cathode (right LED). Pair with pin 14; typically driven by an open-drain PHY LED output. [datasheet p.1]"+ "description": "Yellow LED cathode; the anode is pin 14. [datasheet p.1]" }, { "number": "14", "name": "14", "type": "passive",- "description": "Yellow LED anode (right LED). Forward voltage 1.8V (min) / 2.8V (max), 20mA, 585nm wavelength. Drive via a current-limiting resistor from the PHY's LED output or Vcc. [datasheet p.1]"+ "description": "Yellow LED anode; the cathode is pin 13 (schematic p.1). Right LED seen from the front; 585 nm, forward voltage 1.8 V min / 2.8 V max at 20 mA. [datasheet p.2]" }, { "number": "S1", "name": "SHIELD", "type": "passive",- "description": "Shield / mounting contact (mechanical); connect per the board design. [from symbol]"+ "description": "Shield pin in one of the two 1.63 mm plated holes of the recommended PCB layout (the drawing gives it no name). [datasheet p.3]" }, { "number": "S2", "name": "SHIELD", "type": "passive",- "description": "Shield / mounting contact (mechanical); connect per the board design. [from symbol]"+ "description": "Shield pin in one of the two 1.63 mm plated holes of the recommended PCB layout (the drawing gives it no name). [datasheet p.3]" } ], "provenance": {@@ -160,10 +159,14 @@ "at": "2026-10-09" }, "datasheet": {- "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588887489490112512",- "pages": 2,- "sha256": "06b3f922bf514722f601b1dd44b302e4b0f37f96253ad24e7977fcc441ee985d",- "source_tier": "lcsc"+ "url": "https://hrdzcn.oss-cn-beijing.aliyuncs.com/202601/ab534667d942f65.pdf",+ "pages": 4,+ "sha256": "e9532cda421d20b6ac48e8a412b389f4667e003172ad110d99dfad192c26014d",+ "source_tier": "mfr",+ "retrieved": "2026-10-27",+ "edition": "Rev. B (no date printed; PDF created 2020-02-28)",+ "source_sha256": "d3a5d7212145ea71b6f643d90478eac1cdb08ef26a191cac525d4ab7fb344ac1",+ "text_layer": "docs/hr911130a-datasheet.pdf is HanRun's file with an OCR text layer added (ocrmypdf 15.2 / tesseract 5.3), because HanRun draws its labels as vector outlines; sha256 is the page copy, source_sha256 the file at url" }, "cad": "Footprint and symbol as used on Adom board designs; 3D model: Adom-generated 3D model built from the datasheet dimensions (simplified; CC-BY-SA 4.0); no vendor CAD is redistributed", "pins": {@@ -173,10 +176,6 @@ "refuses_to_fabricate": true } },- "viewers": {- "symbol": "viewers/symbol.html",- "footprint": "viewers/footprint.html"- }, "models_3d": [ { "file": "hr911130a.step",@@ -199,4 +198,4 @@ ] }, "description": "HANRUN(Zhongshan HanRun Elec) Modular/Ethernet Connector (RJ45) Jacks With Magnetics, Through Hole. KiCad symbol, footprint and 3D as used on Adom boards; pin functions from the manufacturer datasheet."-}+}
page.json+36−31@@ -4,14 +4,13 @@ "slug": "hr911130a", "title": "HR911130A", "brief": "HANRUN(Zhongshan HanRun Elec) Modular/Ethernet Connector (RJ45) Jacks With Magnetics, Through Hole. KiCad symbol, footprint and 3D as used on Adom boards; pin functions from the manufacturer datasheet.",- "version": "0.1.0",+ "version": "0.1.1", "license": "CC-BY-SA-4.0", "tags": [ "component", "connectors", "hr911130a",- "board-derived",- "staged-for-validation"+ "board-derived" ], "component": { "mpn": "HR911130A",@@ -20,11 +19,11 @@ "pin_count": 16, "category": "Connectors", "subcategory": "Modular/Ethernet Connector (RJ45) Jacks With Magnetics",- "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588887489490112512",+ "datasheet": "https://hrdzcn.oss-cn-beijing.aliyuncs.com/202601/ab534667d942f65.pdf", "parts": { "symbol": "hr911130a.kicad_sym", "footprint": "hr911130a.kicad_mod",- "model_3d": "hr911130a.glb",+ "model_3d": "hr911130a-hero.glb", "model_3d_plain": "hr911130a.glb", "model_3d_step": "hr911130a.step", "model_3d_step_plain": "hr911130a.step",@@ -32,9 +31,9 @@ }, "distributor_links": { "digikey": false,- "digikey_note": "2026-10-09: no exact-MPN listing for HR911130A found via the digikey API.",+ "digikey_note": "Not carried: searched HR911130A on 2026-10-27.", "mouser": false,- "mouser_note": "2026-10-09: no exact-MPN listing for HR911130A found via the mouser API.",+ "mouser_note": "Not carried: searched HR911130A on 2026-10-27.", "lcsc": { "part": "C54408", "url": "https://www.lcsc.com/product-detail/C54408.html"@@ -45,97 +44,97 @@ "number": "1", "name": "P1", "type": "passive",- "description": "Chip-side pad P1. Internally tied through the Bob-Smith termination network (4x75Ω common node) to the 1000pF/2kV bypass capacitor returning to P10. Typically connected to the chassis/termination ground on the PHY side. [datasheet p.1]"+ "description": "Common centre tap of the four chip-side transformer windings (the drawing labels it P1 only). [datasheet p.1]" }, { "number": "2", "name": "MDI0+", "type": "passive",- "description": "Chip-side pin P2 — MDI pair 0 positive (BI_DA+). Connects to the center-tapped primary of the first 1CT:1CT transformer; routes to UTP pin J1 (A+). Terminate to the PHY's TX/RX pair 0 positive. [datasheet p.1]"+ "description": "MDI 0+ (P2): chip-side winding of a 1CT:1CT transformer; reaches jack contact J1 (A+) through the common-mode choke. [datasheet p.1]" }, { "number": "3", "name": "MDI0-", "type": "passive",- "description": "Chip-side pin P3 — MDI pair 0 negative (BI_DA-). Second lead of pair 0 primary; routes to UTP pin J2 (A-). [datasheet p.1]"+ "description": "MDI 0- (P3): chip-side winding of a 1CT:1CT transformer; reaches jack contact J2 (A-) through the common-mode choke. [datasheet p.1]" }, { "number": "4", "name": "MDI1+", "type": "passive",- "description": "Chip-side pin P4 — MDI pair 1 positive (BI_DB+). Primary lead of the second 1CT:1CT transformer; routes to UTP pin J3 (B+). [datasheet p.1]"+ "description": "MDI 1+ (P4): chip-side winding of a 1CT:1CT transformer; reaches jack contact J3 (B+) through the common-mode choke. [datasheet p.1]" }, { "number": "5", "name": "MDI2+", "type": "passive",- "description": "Chip-side pin P5 — MDI pair 2 positive (BI_DC+). Primary lead of the third 1CT:1CT transformer; routes to UTP pin J5 (C-). Note: UTP pin assignment follows the datasheet schematic. [datasheet p.1]"+ "description": "MDI 2+ (P5): chip-side winding of a 1CT:1CT transformer; reaches jack contact J4 (C+) through the common-mode choke. [datasheet p.1]" }, { "number": "6", "name": "MDI2-", "type": "passive",- "description": "Chip-side pin P6 — MDI pair 2 negative (BI_DC-). Second primary lead of pair 2 transformer; routes to UTP pin J6 (B-). [datasheet p.1]"+ "description": "MDI 2- (P6): chip-side winding of a 1CT:1CT transformer; reaches jack contact J5 (C-) through the common-mode choke. [datasheet p.1]" }, { "number": "7", "name": "MDI1-", "type": "passive",- "description": "Chip-side pin P7 — MDI pair 1 negative (BI_DB-). Second primary lead of pair 1 transformer; routes to UTP pin J4 (C+). [datasheet p.1]"+ "description": "MDI 1- (P7): chip-side winding of a 1CT:1CT transformer; reaches jack contact J6 (B-) through the common-mode choke. [datasheet p.1]" }, { "number": "8", "name": "MDI3+", "type": "passive",- "description": "Chip-side pin P8 — MDI pair 3 positive (BI_DD+). Primary lead of the fourth 1CT:1CT transformer; routes to UTP pin J7 (D+). [datasheet p.1]"+ "description": "MDI 3+ (P8): chip-side winding of a 1CT:1CT transformer; reaches jack contact J7 (D+) through the common-mode choke. [datasheet p.1]" }, { "number": "9", "name": "MDI3-", "type": "passive",- "description": "Chip-side pin P9 — MDI pair 3 negative (BI_DD-). Second primary lead of pair 3 transformer; routes to UTP pin J8 (D-). [datasheet p.1]"+ "description": "MDI 3- (P9): chip-side winding of a 1CT:1CT transformer; reaches jack contact J8 (D-) through the common-mode choke. [datasheet p.1]" }, { "number": "10", "name": "P10", "type": "passive",- "description": "Chip-side pad P10 — Bob-Smith termination return. Connects to the 1000pF/2kV bypass capacitor that ties the common node of the 4x75Ω termination network back to chassis/earth ground. [datasheet p.1]"+ "description": "Termination return: each cable-side centre tap goes through 75 ohms (4 x 75 ohms) to a common node, which reaches P10 through a 1000 pF 2 kV capacitor. [datasheet p.1]" }, { "number": "11", "name": "11", "type": "passive",- "description": "Green LED anode (left LED). Forward voltage 1.8V (min) / 2.8V (max), 20mA, 568nm wavelength. Drive via a current-limiting resistor from the PHY's LED output or Vcc with the cathode (pin 12) sinking to the PHY. [datasheet p.1]"+ "description": "Green LED anode; the cathode is pin 12 (schematic p.1). Left LED seen from the front; 568 nm, forward voltage 1.8 V min / 2.8 V max at 20 mA. [datasheet p.2]" }, { "number": "12", "name": "12", "type": "passive",- "description": "Green LED cathode (left LED). Pair with pin 11; typically driven by an open-drain PHY LED output. [datasheet p.1]"+ "description": "Green LED cathode; the anode is pin 11. [datasheet p.1]" }, { "number": "13", "name": "13", "type": "passive",- "description": "Yellow LED cathode (right LED). Pair with pin 14; typically driven by an open-drain PHY LED output. [datasheet p.1]"+ "description": "Yellow LED cathode; the anode is pin 14. [datasheet p.1]" }, { "number": "14", "name": "14", "type": "passive",- "description": "Yellow LED anode (right LED). Forward voltage 1.8V (min) / 2.8V (max), 20mA, 585nm wavelength. Drive via a current-limiting resistor from the PHY's LED output or Vcc. [datasheet p.1]"+ "description": "Yellow LED anode; the cathode is pin 13 (schematic p.1). Right LED seen from the front; 585 nm, forward voltage 1.8 V min / 2.8 V max at 20 mA. [datasheet p.2]" }, { "number": "S1", "name": "SHIELD", "type": "passive",- "description": "Shield / mounting contact (mechanical); connect per the board design. [from symbol]"+ "description": "Shield pin in one of the two 1.63 mm plated holes of the recommended PCB layout (the drawing gives it no name). [datasheet p.3]" }, { "number": "S2", "name": "SHIELD", "type": "passive",- "description": "Shield / mounting contact (mechanical); connect per the board design. [from symbol]"+ "description": "Shield pin in one of the two 1.63 mm plated holes of the recommended PCB layout (the drawing gives it no name). [datasheet p.3]" } ], "provenance": {@@ -145,10 +144,14 @@ "at": "2026-10-09" }, "datasheet": {- "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588887489490112512",- "pages": 2,- "sha256": "06b3f922bf514722f601b1dd44b302e4b0f37f96253ad24e7977fcc441ee985d",- "source_tier": "lcsc"+ "url": "https://hrdzcn.oss-cn-beijing.aliyuncs.com/202601/ab534667d942f65.pdf",+ "pages": 4,+ "sha256": "e9532cda421d20b6ac48e8a412b389f4667e003172ad110d99dfad192c26014d",+ "source_tier": "mfr",+ "retrieved": "2026-10-27",+ "edition": "Rev. B (no date printed; PDF created 2020-02-28)",+ "source_sha256": "d3a5d7212145ea71b6f643d90478eac1cdb08ef26a191cac525d4ab7fb344ac1",+ "text_layer": "docs/hr911130a-datasheet.pdf is HanRun's file with an OCR text layer added (ocrmypdf 15.2 / tesseract 5.3), because HanRun draws its labels as vector outlines; sha256 is the page copy, source_sha256 the file at url" }, "cad": "Footprint and symbol as used on Adom board designs; 3D model: Adom-generated 3D model built from the datasheet dimensions (simplified; CC-BY-SA 4.0); no vendor CAD is redistributed", "pins": {@@ -220,9 +223,11 @@ "hr911130a.step", "hr911130a.lbr", "docs/hero.png",- "docs/hr911130a-datasheet.pdf"+ "docs/hr911130a-datasheet.pdf",+ "hr911130a-hero.glb",+ "hr911130a-hero.overlay.json" ],- "visibility": {- "public": false- }+ "visibility": "public",+ "description": "HANRUN(Zhongshan HanRun Elec) Modular/Ethernet Connector (RJ45) Jacks With Magnetics, Through Hole. KiCad symbol, footprint and 3D as used on Adom boards; pin functions from the manufacturer datasheet.",+ "org": "adom" }
verification.json+81−2@@ -9,7 +9,7 @@ "name": "Claude (AI build)", "handle": "claude" },- "status": "open",+ "status": "superseded", "title": "Automated build checks (awaiting human validation)", "scope": [ "symbol",@@ -60,7 +60,7 @@ "name": "Claude (AI build)", "handle": "claude" },- "status": "open",+ "status": "superseded", "title": "Datasheet text layer: the manufacturer drawing is a scanned image; the attached PDF is the...", "scope": [ "review"@@ -76,6 +76,85 @@ ], "evidence": [], "files": {}+ },+ {+ "date": "2026-10-27",+ "by": {+ "name": "Claude, at Caleb Taylor's request",+ "handle": "claude"+ },+ "status": "verified",+ "title": "Validated against HanRun's HR911130A datasheet (Rev. B)",+ "scope": [+ "symbol",+ "footprint",+ "3d",+ "pins"+ ],+ "variants": [+ "*"+ ],+ "checks": [+ {+ "text": "Datasheet: replaced the JLCPCB copy with HanRun's own PDF, linked from the HR911130A product page on hanrun.com (https://www.hanrun.com/rj45_1000/203.html) and served from HanRun's file store; 4 pages, Rev. B (no date printed; PDF created 2020-02-28), retrieved 2026-10-27",+ "result": "pass"+ },+ {+ "text": "Datasheet text layer: HanRun's PDF draws the schematic and drawing labels as vector outlines, so the attached copy is the same 4 pages with an OCR text layer added (ocrmypdf 15.2 / tesseract 5.3) for the pin-name text check; the unmodified HanRun file has sha256 d3a5d7212145ea71b6f643d90478eac1cdb08ef26a191cac525d4ab7fb344ac1",+ "result": "note"+ },+ {+ "text": "All 14 numbered pins match the schematic (p.1) by number and name: P1, MDI 0+ P2, MDI 0- P3, MDI 1+ P4, MDI 2+ P5, MDI 2- P6, MDI 1- P7, MDI 3+ P8, MDI 3- P9, P10, LED pins 11-14; the page keeps MDI0+ etc. without the space the drawing prints between MDI and the pair number, with ASCII hyphens for the drawing's minus signs. No pin renamed",+ "result": "pass"+ },+ {+ "text": "LED polarity from the schematic (p.1): green 11 anode -> 12 cathode, yellow 14 anode -> 13 cathode; green is the left LED and yellow the right LED seen from the front (p.2); 568/585 nm, VF 1.8/2.8 V, 20 mA (p.2)",+ "result": "pass"+ },+ {+ "text": "All 16 descriptions rewritten from the datasheet. The old ones had wrong cable-side routing for pins 5, 6 and 7 (the schematic routes MDI 2+ to J4 C+, MDI 2- to J5 C-, MDI 1- to J6 B-) and described P1 as the termination return (P1 is the chip-side centre-tap common; P10 is the 4 x 75 ohm / 1000 pF 2 kV termination return)",+ "result": "pass"+ },+ {+ "text": "Shield pins S1/S2 are unnamed in the drawing (two 1.63 mm holes on the layout, p.3); the page keeps the name SHIELD",+ "result": "note"+ },+ {+ "text": "Footprint vs the recommended PCB layout (p.3, component side view): signal pins 1-10 on 0.89 mm drills at 1.27 mm stagger (2.54 mm within a row), rows 6.35 and 8.89 mm behind the post line, pin 1 at the right end of the rear row; footprint pads at x = +/-5.72, 4.44, 3.18, 1.90, 0.64 vs the drawing's 0.635-mm grid (5.715, 4.445, ...), within 0.005 mm; LED pins on 1.02 mm drills at 13.25 mm outer / 2.54 mm pairs, 4.90 mm in front of the post line; 3.25 mm NPTH posts 11.43 mm apart; 1.63 mm shield holes 15.49 mm apart, 3.05 mm behind the post line. Pin 1 position and LED order (14, 13 ... 12, 11 left to right) match",+ "result": "pass"+ },+ {+ "text": "3D body vs the mechanical drawing (p.2, tolerance +/-0.25): 16.04 x 21.30 x 13.50 mm against B 16.00, A 21.20, C 13.30; front face 10.92 mm and rear 10.38 mm from the post line against 10.80 / 10.40 (p.3); Z-up, seated on z = 0, the model's 18 pins sit on the footprint's 18 holes",+ "result": "pass"+ },+ {+ "text": "3D pin tails reach 3.05 mm below the seating plane against D 3.50 +/-0.30 mm (p.2): 0.15 mm shorter than the minimum; body and footprint unaffected",+ "result": "note"+ },+ {+ "text": "DigiKey and Mouser do not carry HR911130A (searched 2026-10-27); LCSC C54408 kept",+ "result": "note"+ },+ {+ "text": "component-page-verify: all checks pass",+ "result": "pass"+ }+ ],+ "evidence": [+ {+ "label": "datasheet (HanRun, Rev. B)",+ "href": "https://hrdzcn.oss-cn-beijing.aliyuncs.com/202601/ab534667d942f65.pdf"+ },+ {+ "label": "product page (hanrun.com)",+ "href": "https://www.hanrun.com/rj45_1000/203.html"+ }+ ],+ "files": {+ "hr911130a.kicad_sym": "737840b39a53e78ba327020db33c039aaeae0c5d6bfad7a6f2aa121a04ce49f2",+ "hr911130a.kicad_mod": "ef6edeb2ef490dca592e62b2cc5fe77fba508d7a41e1461db9b74fa12e629476",+ "hr911130a.step": "bd0a6014606a9b3a5fd7d73faa17c35387b980934a0545bb575d867c8057b608"+ } } ] }