← Commit history

hr1001cgs-z: factory component page (tier=lcsc)

Ray ·cbb43eb27a · ·parent bd65251
1 file changed +170−8
page.json+170−8
@@ -1,13 +1,180 @@ {+  "schema_version": 1,+  "type": "component",   "slug": "hr1001cgs-z",+  "title": "HR1001CGS-Z",+  "brief": "Monolithic Power Systems AC-DC Controllers And Regulators, SOIC-16. Datasheet-verified pinout, KiCad symbol/footprint/3D.",   "version": "0.1.0",-  "type": "component",-  "description": "Monolithic Power Systems AC-DC Controllers And Regulators, SOIC-16. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "license": "CC-BY-SA-4.0",   "tags": [     "component",     "power management (pmic)",     "hr1001cgs-z"   ],+  "component": {+    "mpn": "HR1001CGS-Z",+    "manufacturer": "Monolithic Power Systems",+    "package": "SOIC-16",+    "pin_count": 16,+    "category": "Power Management (PMIC)",+    "subcategory": "AC-DC Controllers And Regulators",+    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8603388520325537792",+    "parts": {+      "symbol": "hr1001cgs-z.kicad_sym",+      "footprint": "hr1001cgs-z.kicad_mod",+      "model_3d": "hr1001cgs-z.glb",+      "model_3d_step": "hr1001cgs-z.step",+      "lbr": "hr1001cgs-z.lbr"+    },+    "distributor_links": {},+    "pins": [+      {+        "number": "1",+        "name": "SS",+        "type": "passive",+        "description": "Soft start. Connect an external capacitor from SS to GND and a resistor to FSET to program the maximum oscillator frequency and the frequency-shift time constant during start-up. An internal switch discharges this capacitor when the chip turns off (VCC < UVLO, BO fault, LATCH tripped, CS > VCS-OCP, TIMER > VTIMER-fmax, or thermal shutdown) to guarantee a soft start on the next cycle."+      },+      {+        "number": "2",+        "name": "TIMER",+        "type": "passive",+        "description": "Over-current-to-shutdown period. A capacitor and resistor from TIMER to GND set the maximum duration allowed in over-current before the IC stops switching and the delay before it resumes. An internal current source ITIMER charges the capacitor whenever VCS > VCS-OCR; the external resistor discharges it slowly. Reaching VTIMER-fmax forces the SS cap to fully discharge (freq \u2192 max); exceeding VTIMER-SD halts switching until the voltage decays below VTIMER-R, when the IC re-enters soft start."+      },+      {+        "number": "3",+        "name": "CT",+        "type": "passive",+        "description": "Oscillator timing capacitor. An internal current source (programmed by the network on FSET) alternately charges and discharges a capacitor tied from CT to GND between VCFp and VCFv thresholds, setting the converter's switching frequency."+      },+      {+        "number": "4",+        "name": "FSET",+        "type": "passive",+        "description": "Switching frequency set / precise 2 V reference. A resistor from FSET to GND defines the current that sets the minimum oscillator frequency. Tying the optocoupler phototransistor to FSET through a resistor closes the feedback loop that modulates the oscillator and regulates the output; that resistor's value sets the maximum operating frequency. An R-C series from FSET to GND sets the start-up frequency shift to limit inrush energy. Source current rating 2 mA max."+      },+      {+        "number": "5",+        "name": "BURST",+        "type": "input",+        "description": "Burst-mode threshold. BURST senses the feedback-related voltage and is compared to an internal VBurst reference. Below VBurst the IC enters an idle low-Iq state; when feedback drives BURST above VBurst + 30 mV (VBurst-hys) switching resumes with no soft start. This enables light-load burst operation whose entry point is set by a resistor from the optocoupler to FSET. Tie BURST to FSET if burst mode is not used."+      },+      {+        "number": "6",+        "name": "CS",+        "type": "input",+        "description": "Half-bridge current sense (also used for CMP). Sensed via a resistor or capacitive divider on the primary. Three functions: (1) over-current regulation - VCS > VCS-OCR discharges SS and pushes frequency up; (2) over-current protection - VCS > VCS-OCP with VSS < VSS-OCP latches OCP off (cleared by cycling VCC below UVLO); (3) capacitive-mode protection - CS is compared to VCSNR/VCSPR after each gate turn-off to block the opposite gate until the correct dV/dt slope is detected or the CMP timer expires. Absolute rating \u22123 V to +6 V. Tie CS to GND if CMP is not used."+      },+      {+        "number": "7",+        "name": "BO",+        "type": "input",+        "description": "Input voltage sense and brown-in/brown-out protection. When BO rises above VBO-On the IC enables the gate drivers; when BO falls below VBO-Off the IC is disabled. Also supports remote on/off."+      },+      {+        "number": "8",+        "name": "LATCH",+        "type": "input",+        "description": "IC latched shutdown input. When VLATCH is exceeded the IC shuts down and drops its bias current near the pre-start-up level. Reset only when VCC is discharged below its UVLO threshold. Connect LATCH to GND if not used."+      },+      {+        "number": "9",+        "name": "HBVS",+        "type": "input",+        "description": "Half-bridge dV/dt sense for adaptive dead-time. A high-voltage capacitor is tied between SW and HBVS; the dV/dt current through HBVS is measured to adaptively adjust the dead time between HG and LG. Sink current \u00b165 mA max."+      },+      {+        "number": "10",+        "name": "GND",+        "type": "power_in",+        "description": "Ground. Return for the low-side gate driver and the IC bias. Route separate traces from GND to the signal ground and to the pulsed gate-current return."+      },+      {+        "number": "11",+        "name": "LG",+        "type": "output",+        "description": "Low-side gate driver output. Push-pull driver with \u00b10.8 A peak source/sink to drive the low-side half-bridge MOSFET. Held at GND during UVLO. Voltage rating \u22120.3 V to VCC."+      },+      {+        "number": "12",+        "name": "VCC",+        "type": "power_in",+        "description": "Supply voltage for the IC bias and the low-side gate driver. Recommended operating range 13 V to 15.5 V (self-limited internally). Decouple with a small (e.g. 0.1 \u00b5F) bypass capacitor at the pin."+      },+      {+        "number": "13",+        "name": "NC",+        "type": "unconnected",+        "description": "High-voltage spacer. No internal connection. Provided to isolate the high-voltage SW pin from the low-voltage side and to ease safety-agency creepage-distance compliance on the PCB."+      },+      {+        "number": "14",+        "name": "SW",+        "type": "power_in",+        "description": "High-side driver source / half-bridge switching node return. Current return for the high-side gate drive. Requires careful layout to avoid large negative spikes below GND. Rated \u22123 V to +600 V with a maximum dV/dt of 50 V/ns."+      },+      {+        "number": "15",+        "name": "HG",+        "type": "output",+        "description": "High-side floating gate driver output. Push-pull driver with \u00b10.8 A peak source/sink to drive the upper half-bridge MOSFET, referenced to SW. An internal pull-down resistor to SW prevents HG from floating during UVLO."+      },+      {+        "number": "16",+        "name": "BST",+        "type": "power_in",+        "description": "Bootstrap supply for the floating high-side gate driver. Connect a bootstrap capacitor between BST and SW; it is charged by an internal bootstrap diode driven in phase with the low-side gate driver. Absolute rating \u22120.3 V to +618 V."+      }+    ],+    "provenance": {+      "extractor": "ds2sf",+      "datasheet": {+        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8603388520325537792",+        "pages": null,+        "sha256": "05a190f3b063515a",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 16,+        "described": 16,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "metadata": {+    "specs": {+      "Manufacturer": "Monolithic Power Systems",+      "Package": "SOIC-16",+      "Category": "Power Management (PMIC)",+      "Pins": "16"+    }+  },+  "variants": [+    {+      "mpn": "HR1001CGS-Z",+      "kind": "packaging"+    }+  ],+  "sections": [+    "hero",+    "viewers",+    "readme",+    "breadcrumbs",+    "info"+  ],+  "discovery_triggers": [+    "hr1001cgs-z"+  ],+  "discovery_pitch": "HR1001CGS-Z (Monolithic Power Systems) component page with datasheet-verified CAD.",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  },   "dependencies": {},   "hero": {     "type": "image",@@ -25,10 +192,5 @@     "docs/hr1001cgs-z-datasheet.pdf",     "viewers/symbol.html",     "viewers/footprint.html"-  ],-  "visibility": "public",-  "author": {-    "name": "Ray",-    "email": "[email protected]"-  }+  ] }\ No newline at end of file