← Commit history

Set visibility: public

Ray ·8f9966fc02 · ·parent 29c8ae7
1 file changed +12−9
page.json+12−9
@@ -38,7 +38,7 @@         "number": "2",         "name": "TIMER",         "type": "passive",-        "description": "Over-current-to-shutdown period. A capacitor and resistor from TIMER to GND set the maximum duration allowed in over-current before the IC stops switching and the delay before it resumes. An internal current source ITIMER charges the capacitor whenever VCS > VCS-OCR; the external resistor discharges it slowly. Reaching VTIMER-fmax forces the SS cap to fully discharge (freq \u2192 max); exceeding VTIMER-SD halts switching until the voltage decays below VTIMER-R, when the IC re-enters soft start."+        "description": "Over-current-to-shutdown period. A capacitor and resistor from TIMER to GND set the maximum duration allowed in over-current before the IC stops switching and the delay before it resumes. An internal current source ITIMER charges the capacitor whenever VCS > VCS-OCR; the external resistor discharges it slowly. Reaching VTIMER-fmax forces the SS cap to fully discharge (freq → max); exceeding VTIMER-SD halts switching until the voltage decays below VTIMER-R, when the IC re-enters soft start."       },       {         "number": "3",@@ -62,7 +62,7 @@         "number": "6",         "name": "CS",         "type": "input",-        "description": "Half-bridge current sense (also used for CMP). Sensed via a resistor or capacitive divider on the primary. Three functions: (1) over-current regulation - VCS > VCS-OCR discharges SS and pushes frequency up; (2) over-current protection - VCS > VCS-OCP with VSS < VSS-OCP latches OCP off (cleared by cycling VCC below UVLO); (3) capacitive-mode protection - CS is compared to VCSNR/VCSPR after each gate turn-off to block the opposite gate until the correct dV/dt slope is detected or the CMP timer expires. Absolute rating \u22123 V to +6 V. Tie CS to GND if CMP is not used."+        "description": "Half-bridge current sense (also used for CMP). Sensed via a resistor or capacitive divider on the primary. Three functions: (1) over-current regulation - VCS > VCS-OCR discharges SS and pushes frequency up; (2) over-current protection - VCS > VCS-OCP with VSS < VSS-OCP latches OCP off (cleared by cycling VCC below UVLO); (3) capacitive-mode protection - CS is compared to VCSNR/VCSPR after each gate turn-off to block the opposite gate until the correct dV/dt slope is detected or the CMP timer expires. Absolute rating −3 V to +6 V. Tie CS to GND if CMP is not used."       },       {         "number": "7",@@ -80,7 +80,7 @@         "number": "9",         "name": "HBVS",         "type": "input",-        "description": "Half-bridge dV/dt sense for adaptive dead-time. A high-voltage capacitor is tied between SW and HBVS; the dV/dt current through HBVS is measured to adaptively adjust the dead time between HG and LG. Sink current \u00b165 mA max."+        "description": "Half-bridge dV/dt sense for adaptive dead-time. A high-voltage capacitor is tied between SW and HBVS; the dV/dt current through HBVS is measured to adaptively adjust the dead time between HG and LG. Sink current ±65 mA max."       },       {         "number": "10",@@ -92,13 +92,13 @@         "number": "11",         "name": "LG",         "type": "output",-        "description": "Low-side gate driver output. Push-pull driver with \u00b10.8 A peak source/sink to drive the low-side half-bridge MOSFET. Held at GND during UVLO. Voltage rating \u22120.3 V to VCC."+        "description": "Low-side gate driver output. Push-pull driver with ±0.8 A peak source/sink to drive the low-side half-bridge MOSFET. Held at GND during UVLO. Voltage rating −0.3 V to VCC."       },       {         "number": "12",         "name": "VCC",         "type": "power_in",-        "description": "Supply voltage for the IC bias and the low-side gate driver. Recommended operating range 13 V to 15.5 V (self-limited internally). Decouple with a small (e.g. 0.1 \u00b5F) bypass capacitor at the pin."+        "description": "Supply voltage for the IC bias and the low-side gate driver. Recommended operating range 13 V to 15.5 V (self-limited internally). Decouple with a small (e.g. 0.1 µF) bypass capacitor at the pin."       },       {         "number": "13",@@ -110,19 +110,19 @@         "number": "14",         "name": "SW",         "type": "power_in",-        "description": "High-side driver source / half-bridge switching node return. Current return for the high-side gate drive. Requires careful layout to avoid large negative spikes below GND. Rated \u22123 V to +600 V with a maximum dV/dt of 50 V/ns."+        "description": "High-side driver source / half-bridge switching node return. Current return for the high-side gate drive. Requires careful layout to avoid large negative spikes below GND. Rated −3 V to +600 V with a maximum dV/dt of 50 V/ns."       },       {         "number": "15",         "name": "HG",         "type": "output",-        "description": "High-side floating gate driver output. Push-pull driver with \u00b10.8 A peak source/sink to drive the upper half-bridge MOSFET, referenced to SW. An internal pull-down resistor to SW prevents HG from floating during UVLO."+        "description": "High-side floating gate driver output. Push-pull driver with ±0.8 A peak source/sink to drive the upper half-bridge MOSFET, referenced to SW. An internal pull-down resistor to SW prevents HG from floating during UVLO."       },       {         "number": "16",         "name": "BST",         "type": "power_in",-        "description": "Bootstrap supply for the floating high-side gate driver. Connect a bootstrap capacitor between BST and SW; it is charged by an internal bootstrap diode driven in phase with the low-side gate driver. Absolute rating \u22120.3 V to +618 V."+        "description": "Bootstrap supply for the floating high-side gate driver. Connect a bootstrap capacitor between BST and SW; it is charged by an internal bootstrap diode driven in phase with the low-side gate driver. Absolute rating −0.3 V to +618 V."       }     ],     "provenance": {@@ -192,5 +192,8 @@     "docs/hr1001cgs-z-datasheet.pdf",     "viewers/symbol.html",     "viewers/footprint.html"-  ]+  ],+  "visibility": {+    "public": true+  } }\ No newline at end of file