← Commit history
README.mdadded+57@@ -0,0 +1,57 @@+# HR1001CGS-Z++**Monolithic Power Systems** · AC-DC Controllers And Regulators · SOIC-16++HR1001CGS-Z from Monolithic Power Systems, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | SS | passive | Soft start. Connect an external capacitor from SS to GND and a resistor to FSET to program the maximum oscillator frequency and the frequency-shift time constant during start-up. An internal switch discharges this capacitor when the chip turns off (VCC < UVLO, BO fault, LATCH tripped, CS > VCS-OCP, TIMER > VTIMER-fmax, or thermal shutdown) to guarantee a soft start on the next cycle. |+| 2 | TIMER | passive | Over-current-to-shutdown period. A capacitor and resistor from TIMER to GND set the maximum duration allowed in over-current before the IC stops switching and the delay before it resumes. An internal current source ITIMER charges the capacitor whenever VCS > VCS-OCR; the external resistor discharges it slowly. Reaching VTIMER-fmax forces the SS cap to fully discharge (freq → max); exceeding VTIMER-SD halts switching until the voltage decays below VTIMER-R, when the IC re-enters soft start. |+| 3 | CT | passive | Oscillator timing capacitor. An internal current source (programmed by the network on FSET) alternately charges and discharges a capacitor tied from CT to GND between VCFp and VCFv thresholds, setting the converter's switching frequency. |+| 4 | FSET | passive | Switching frequency set / precise 2 V reference. A resistor from FSET to GND defines the current that sets the minimum oscillator frequency. Tying the optocoupler phototransistor to FSET through a resistor closes the feedback loop that modulates the oscillator and regulates the output; that resistor's value sets the maximum operating frequency. An R-C series from FSET to GND sets the start-up frequency shift to limit inrush energy. Source current rating 2 mA max. |+| 5 | BURST | input | Burst-mode threshold. BURST senses the feedback-related voltage and is compared to an internal VBurst reference. Below VBurst the IC enters an idle low-Iq state; when feedback drives BURST above VBurst + 30 mV (VBurst-hys) switching resumes with no soft start. This enables light-load burst operation whose entry point is set by a resistor from the optocoupler to FSET. Tie BURST to FSET if burst mode is not used. |+| 6 | CS | input | Half-bridge current sense (also used for CMP). Sensed via a resistor or capacitive divider on the primary. Three functions: (1) over-current regulation - VCS > VCS-OCR discharges SS and pushes frequency up; (2) over-current protection - VCS > VCS-OCP with VSS < VSS-OCP latches OCP off (cleared by cycling VCC below UVLO); (3) capacitive-mode protection - CS is compared to VCSNR/VCSPR after each gate turn-off to block the opposite gate until the correct dV/dt slope is detected or the CMP timer expires. Absolute rating −3 V to +6 V. Tie CS to GND if CMP is not used. |+| 7 | BO | input | Input voltage sense and brown-in/brown-out protection. When BO rises above VBO-On the IC enables the gate drivers; when BO falls below VBO-Off the IC is disabled. Also supports remote on/off. |+| 8 | LATCH | input | IC latched shutdown input. When VLATCH is exceeded the IC shuts down and drops its bias current near the pre-start-up level. Reset only when VCC is discharged below its UVLO threshold. Connect LATCH to GND if not used. |+| 9 | HBVS | input | Half-bridge dV/dt sense for adaptive dead-time. A high-voltage capacitor is tied between SW and HBVS; the dV/dt current through HBVS is measured to adaptively adjust the dead time between HG and LG. Sink current ±65 mA max. |+| 10 | GND | power_in | Ground. Return for the low-side gate driver and the IC bias. Route separate traces from GND to the signal ground and to the pulsed gate-current return. |+| 11 | LG | output | Low-side gate driver output. Push-pull driver with ±0.8 A peak source/sink to drive the low-side half-bridge MOSFET. Held at GND during UVLO. Voltage rating −0.3 V to VCC. |+| 12 | VCC | power_in | Supply voltage for the IC bias and the low-side gate driver. Recommended operating range 13 V to 15.5 V (self-limited internally). Decouple with a small (e.g. 0.1 µF) bypass capacitor at the pin. |+| 13 | NC | unconnected | High-voltage spacer. No internal connection. Provided to isolate the high-voltage SW pin from the low-voltage side and to ease safety-agency creepage-distance compliance on the PCB. |+| 14 | SW | power_in | High-side driver source / half-bridge switching node return. Current return for the high-side gate drive. Requires careful layout to avoid large negative spikes below GND. Rated −3 V to +600 V with a maximum dV/dt of 50 V/ns. |+| 15 | HG | output | High-side floating gate driver output. Push-pull driver with ±0.8 A peak source/sink to drive the upper half-bridge MOSFET, referenced to SW. An internal pull-down resistor to SW prevents HG from floating during UVLO. |+| 16 | BST | power_in | Bootstrap supply for the floating high-side gate driver. Connect a bootstrap capacitor between BST and SW; it is charged by an internal bootstrap diode driven in phase with the low-side gate driver. Absolute rating −0.3 V to +618 V. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Monolithic Power Systems |+| Package | SOIC-16 |+| Category | Power Management (PMIC) |+| Pins | 16 |++## Ordering variants++Same part, different packaging or reel option.++- `HR1001CGS-Z`++## CAD (KiCad official)++- Symbol: `HR1001CGS-Z`+- Footprint: `Package_SO:SOIC-16_3.9x9.9mm_P1.27mm`+- 3D model: SOIC-16 (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Monolithic Power Systems datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8603388520325537792) (None pp, sha256 `05a190f3b063515a`, retrieved 2026-08-17, tier: lcsc)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/hr1001cgs-z-datasheet.pdf)
page.jsonadded+34@@ -0,0 +1,34 @@+{+ "slug": "hr1001cgs-z",+ "version": "0.1.0",+ "type": "component",+ "description": "Monolithic Power Systems AC-DC Controllers And Regulators, SOIC-16. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "power management (pmic)",+ "hr1001cgs-z"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "hr1001cgs-z.kicad_sym",+ "hr1001cgs-z.kicad_mod",+ "hr1001cgs-z.glb",+ "hr1001cgs-z.step",+ "hr1001cgs-z.lbr",+ "docs/hero.png",+ "docs/hr1001cgs-z-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ],+ "visibility": "public",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}