← Commit history

hg9200bm: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·b01322c785 · ·parent 617e3c9
1 file changed +110−1
page.json+110−1
@@ -30,5 +30,114 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "HG9200BM",+    "manufacturer": "HGSEMI",+    "package": "SOP-14",+    "pin_count": 14,+    "category": "Audio Interface ICs",+    "parts": {+      "symbol": "hg9200bm.kicad_sym",+      "footprint": "hg9200bm.kicad_mod",+      "model_3d": "hg9200bm-etched.glb",+      "model_3d_plain": "hg9200bm.glb",+      "model_3d_step": "hg9200bm-etched.step",+      "model_3d_step_plain": "hg9200bm.step",+      "lbr": "hg9200bm.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "CE",+        "type": "input",+        "description": "Chip enable, active low. CMOS input with internal pull-high. Drive low to enable oscillator and DTMF output; drive high to place the device in standby (I_STB ≤ 2 µA at 5 V)."+      },+      {+        "number": "2",+        "name": "X2",+        "type": "output",+        "description": "Oscillator output. Along with X1 forms the inverter/bias-resistor oscillator with on-chip load capacitors. Connect a standard 3.579545 MHz crystal between X1 and X2."+      },+      {+        "number": "3",+        "name": "X1",+        "type": "input",+        "description": "Oscillator input. Connect a standard 3.579545 MHz crystal or ceramic resonator between X1 and X2. Internal bias resistor (~10 MΩ) and load caps (~20 pF/10 pF) are integrated."+      },+      {+        "number": "4",+        "name": "VSS",+        "type": "power_in",+        "description": "Negative supply / ground reference."+      },+      {+        "number": "5",+        "name": "NC",+        "type": "unconnected",+        "description": "No internal connection. Leave floating or tie to ground per board convention."+      },+      {+        "number": "6",+        "name": "D0",+        "type": "input",+        "description": "Parallel-mode data input bit 0 (LSB of the 4-bit digit code in Table 2). In serial mode this pin is pulled high internally and should be left floating; in parallel mode it must not be floated."+      },+      {+        "number": "7",+        "name": "D1",+        "type": "input",+        "description": "Parallel-mode data input bit 1. Pull-high internal resistor when in serial mode; drive as parallel data input when S/P=H."+      },+      {+        "number": "8",+        "name": "D2",+        "type": "input",+        "description": "Parallel-mode data input bit 2. Pull-high internal resistor when in serial mode; drive as parallel data input when S/P=H."+      },+      {+        "number": "9",+        "name": "D3",+        "type": "input",+        "description": "Parallel-mode data input bit 3 (MSB of the 4-bit parallel code). Pull-high internal resistor when in serial mode; drive as parallel data input when S/P=H."+      },+      {+        "number": "10",+        "name": "S/P",+        "type": "input",+        "description": "Operation-mode select. CMOS input: S/P = H selects parallel mode (D0-D3 drive the tone code); S/P = L selects serial mode (DATA/CLK stream a 5-bit code)."+      },+      {+        "number": "11",+        "name": "CLK",+        "type": "input",+        "description": "Serial-mode synchronous clock input. In parallel mode this pin is pulled high internally and can be left floating; in serial mode it clocks in 5-bit codes on the falling edge (100 kHz typ, 500 kHz max)."+      },+      {+        "number": "12",+        "name": "DATA",+        "type": "input",+        "description": "Serial-mode data input. In parallel mode this pin is pulled high internally and can be left floating; in serial mode it is latched on the falling edge of CLK, D0 (LSB) first."+      },+      {+        "number": "13",+        "name": "DTMF",+        "type": "output",+        "description": "DTMF analog output. CMOS output providing the selected single/dual tone (V_TAC ≈ 0.15 Vrms into R_L=5 kΩ, DC level ≈ 0.45-0.75 × VDD). Requires R_L ≥ 5 kΩ."+      },+      {+        "number": "14",+        "name": "VDD",+        "type": "power_in",+        "description": "Positive supply, 2.0-5.5 V for normal operation. I_DD ≈ 240 µA at 2.5 V and 950 µA at 5.0 V with CE=VSS and no load."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}