← Commit history

hg24c16n: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·1d46943fec · ·parent 8ba6911
1 file changed +74−1
page.json+74−1
@@ -33,5 +33,78 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "HG24C16N",+    "manufacturer": "HGSEMI",+    "package": "DIP-8",+    "pin_count": 8,+    "category": "EEPROM",+    "parts": {+      "symbol": "hg24c16n.kicad_sym",+      "footprint": "hg24c16n.kicad_mod",+      "model_3d": "hg24c16n-etched.glb",+      "model_3d_plain": "hg24c16n.glb",+      "model_3d_step": "hg24c16n-etched.step",+      "model_3d_step_plain": "hg24c16n.step",+      "lbr": "hg24c16n.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "A0",+        "type": "unconnected",+        "description": "No connect on the HG24C16 (the 16K variant does not use device-address pins). May be left floating or tied to GND for lowest noise. On smaller-density parts in the family, A0 is a hard-wired I2C slave-address input."+      },+      {+        "number": "2",+        "name": "A1",+        "type": "unconnected",+        "description": "No connect on the HG24C16. May be left floating or tied to GND. On smaller-density parts in the family, A1 is a hard-wired I2C slave-address input."+      },+      {+        "number": "3",+        "name": "A2",+        "type": "unconnected",+        "description": "No connect on the HG24C16. May be left floating or tied to GND. On smaller-density parts in the family, A2 is a hard-wired I2C slave-address input."+      },+      {+        "number": "4",+        "name": "GND",+        "type": "power_in",+        "description": "Ground reference for supply and all I/O signals."+      },+      {+        "number": "5",+        "name": "SDA",+        "type": "bidirectional",+        "description": "I2C serial data. Bidirectional open-drain line; requires an external pull-up resistor to VCC (typically 1.3 kΩ at 2.5-5 V or 10 kΩ at 1.8 V). May be wire-ORed with other open-drain devices on the same bus."+      },+      {+        "number": "6",+        "name": "SCL",+        "type": "input",+        "description": "I2C serial clock input. Positive edge clocks data into the EEPROM, negative edge clocks data out. Requires an external pull-up to VCC. Supports up to 1 MHz at 5 V and 400 kHz at 1.7-2.7 V."+      },+      {+        "number": "7",+        "name": "WP",+        "type": "input",+        "description": "Write Protect. Tie to GND for normal read/write operation; tie to VCC to hardware-protect the full 16K array against writes. Schmitt-trigger filtered input."+      },+      {+        "number": "8",+        "name": "VCC",+        "type": "power_in",+        "description": "Positive supply, 1.7 V to 5.5 V. Typical operating current 0.4 mA (read) / 2.0 mA (write) at 5 V, 100 kHz; standby current 2.0 µA max. Absolute maximum 6.5 V."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}