hg24c16mm

@@ -33,5 +33,78 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "HG24C16MM",+    "manufacturer": "HGSEMI",+    "package": "MSOP-8",+    "pin_count": 8,+    "category": "EEPROM",+    "parts": {+      "symbol": "hg24c16mm.kicad_sym",+      "footprint": "hg24c16mm.kicad_mod",+      "model_3d": "hg24c16mm-etched.glb",+      "model_3d_plain": "hg24c16mm.glb",+      "model_3d_step": "hg24c16mm-etched.step",+      "model_3d_step_plain": "hg24c16mm.step",+      "lbr": "hg24c16mm.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "A0",+        "type": "unconnected",+        "description": "Device address input A0. On the HG24C16 the device-address pins are not used for hard-wired addressing (the 16K uses these bits as internal page-address bits), so this pin is a no-connect and may be tied to GND. Input capacitance ~6 pF."+      },+      {+        "number": "2",+        "name": "A1",+        "type": "unconnected",+        "description": "Device address input A1. On the HG24C16 this pin is a no-connect (page-address bit internally) and may be tied to GND. Input capacitance ~6 pF."+      },+      {+        "number": "3",+        "name": "A2",+        "type": "unconnected",+        "description": "Device address input A2. On the HG24C16 this pin is a no-connect (page-address bit internally) and may be tied to GND. Input capacitance ~6 pF."+      },+      {+        "number": "4",+        "name": "GND",+        "type": "power_in",+        "description": "Ground reference for the device. Tie WP to GND for normal read/write operation."+      },+      {+        "number": "5",+        "name": "SDA",+        "type": "bidirectional",+        "description": "Serial data I/O for the two-wire (I2C-compatible) interface. Open-drain output; requires an external pull-up to VCC and may be wire-ORed with other open-drain/open-collector devices. I/O capacitance ~8 pF. VOL ≤ 0.4 V at IOL = 3 mA (VCC = 5 V)."+      },+      {+        "number": "6",+        "name": "SCL",+        "type": "input",+        "description": "Serial clock input for the two-wire interface. Data is clocked into the EEPROM on the positive edge and clocked out on the negative edge. Schmitt-trigger, filtered input for noise suppression. Max fSCL = 1 MHz at VCC = 5 V (400 kHz at 1.8-2.7 V)."+      },+      {+        "number": "7",+        "name": "WP",+        "type": "input",+        "description": "Write Protect input. When tied to GND, normal read/write operations are allowed. When tied to VCC, the full 16 K array is write-protected (hardware data protection). VIH ≥ 0.7·VCC, VIL ≤ 0.3·VCC."+      },+      {+        "number": "8",+        "name": "VCC",+        "type": "power_in",+        "description": "Positive supply voltage input, 1.7 V to 5.5 V. Typical read current ICC1 = 0.4 mA @ 5 V/100 kHz; typical write current ICC2 = 2.0 mA (3 mA max). Standby current ISB ≤ 2 µA. Absolute max 6.5 V."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}