← Commit history
hg24c04m: restore the component block (pinout + model declarations) from this page's own README and symbol
1 file changed
+74−1
page.json+74−1@@ -33,5 +33,78 @@ "author": { "name": "Ray", "email": "[email protected]"+ },+ "component": {+ "mpn": "HG24C04M",+ "manufacturer": "HGSEMI",+ "package": "SOP-8",+ "pin_count": 8,+ "category": "EEPROM",+ "parts": {+ "symbol": "hg24c04m.kicad_sym",+ "footprint": "hg24c04m.kicad_mod",+ "model_3d": "hg24c04m-etched.glb",+ "model_3d_plain": "hg24c04m.glb",+ "model_3d_step": "hg24c04m-etched.step",+ "model_3d_step_plain": "hg24c04m.step",+ "lbr": "hg24c04m.lbr"+ },+ "pins": [+ {+ "number": "1",+ "name": "A0",+ "type": "input",+ "description": "Device address input A0. Not used on the HG24C04 (only A2 and A1 participate in device addressing); this pin is a no-connect and may be tied to GND."+ },+ {+ "number": "2",+ "name": "A1",+ "type": "input",+ "description": "Device address input A1. Hard-wired to VCC or GND to set one of the device-select bits so that up to four HG24C04 devices can share a single two-wire bus. VIL <= 0.3*VCC, VIH >= 0.7*VCC."+ },+ {+ "number": "3",+ "name": "A2",+ "type": "input",+ "description": "Device address input A2. Hard-wired to VCC or GND to set one of the device-select bits so that up to four HG24C04 devices can share a single two-wire bus. VIL <= 0.3*VCC, VIH >= 0.7*VCC."+ },+ {+ "number": "4",+ "name": "GND",+ "type": "power_in",+ "description": "Ground reference (0 V) for the device."+ },+ {+ "number": "5",+ "name": "SDA",+ "type": "bidirectional",+ "description": "Serial data line for the two-wire interface. Open-drain output, so an external pull-up (typ. 1.3 kOhm at 2.5-5 V, 10 kOhm at 1.8 V) to VCC is required. Bidirectional; may be wire-ORed with other open-drain devices. Input capacitance <= 8 pF."+ },+ {+ "number": "6",+ "name": "SCL",+ "type": "input",+ "description": "Serial clock input for the two-wire interface. Positive edge clocks data in, negative edge clocks data out. Supports up to 1 MHz at 5 V and 400 kHz at 1.8/2.5/2.7 V. Input capacitance <= 6 pF."+ },+ {+ "number": "7",+ "name": "WP",+ "type": "input",+ "description": "Write Protect. Tie to GND for normal read/write operation; tie to VCC to hardware-protect the full 4 K array against writes."+ },+ {+ "number": "8",+ "name": "VCC",+ "type": "power_in",+ "description": "Positive supply input, 1.7 V to 5.5 V (absolute max 6.5 V). Typical ICC = 0.4 mA read / 2.0 mA write at 5.0 V, 100 kHz; standby current <= 2 uA."+ }+ ],+ "provenance": {+ "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ } }-}+}