← Commit history
hd688adr: restore the component block (pinout + model declarations) from this page's own README and symbol
1 file changed
+122−1
page.json+122−1@@ -33,5 +33,126 @@ "author": { "name": "Ray", "email": "[email protected]"+ },+ "component": {+ "mpn": "HD688ADR",+ "manufacturer": "Broadic",+ "package": "SOP-16",+ "pin_count": 16,+ "category": "RS-485/RS-422 ICs",+ "parts": {+ "symbol": "hd688adr.kicad_sym",+ "footprint": "hd688adr.kicad_mod",+ "model_3d": "hd688adr-etched.glb",+ "model_3d_plain": "hd688adr.glb",+ "model_3d_step": "hd688adr-etched.step",+ "model_3d_step_plain": "hd688adr.step",+ "lbr": "hd688adr.lbr"+ },+ "pins": [+ {+ "number": "1",+ "name": "BUSL2",+ "type": "passive",+ "description": "Meter-bus line 2 connection. One of the two polarity-insensitive M-Bus terminals; typically connected to the bus through a series protection resistor (RL2 ≈ 220 Ω)."+ },+ {+ "number": "2",+ "name": "VB",+ "type": "passive",+ "description": "Rectified bus voltage output. Provides the rectified M-Bus signal after the internal bridge (BR); reference for VSTC and the PF undervoltage detector."+ },+ {+ "number": "3",+ "name": "STC",+ "type": "passive",+ "description": "External power-hold capacitor pin (CSTC). Stores energy from the bus to keep VDD alive during transmit modulation; recommended CSTC ≥ 50 µF (≤220 µF at RRIDD=13 kΩ, ≤470 µF at RRIDD=30 kΩ)."+ },+ {+ "number": "4",+ "name": "RIDD",+ "type": "passive",+ "description": "External resistor pin to set CS1 quiescent bus current. RRIDD = 13-80 kΩ (13 kΩ → IBUS ≈ 3 mA, 30 kΩ → IBUS ≈ 1.5 mA); VRIDD ≈ 1.23-1.33 V at 30 kΩ."+ },+ {+ "number": "5",+ "name": "PF",+ "type": "output",+ "description": "Power-fail / undervoltage indication output. Signals bus undervoltage: high (≈VBAT − 0.6 V) when VVB ≥ VSTC + 0.8 V, low (≤0.9 V) when VVB ≤ VSTC + 0.3 V."+ },+ {+ "number": "6",+ "name": "SC",+ "type": "passive",+ "description": "External sample/hold capacitor pin (CSC) for the receiver's dynamic threshold circuit. Charging current typ. −15 to −40 µA at VSC = 24 V; VSC tracks VVB."+ },+ {+ "number": "7",+ "name": "TXI",+ "type": "output",+ "description": "Inverted transmit data output. Complementary to TX; VOH ≈ VBAT − 0.6 V at IOH = −100 µA, VOL ≤ 0.5 V at IOL = 100 µA. Used together with TX to drive the bus modulator (optionally via an optocoupler)."+ },+ {+ "number": "8",+ "name": "TX",+ "type": "output",+ "description": "Transmit data output (non-inverted). Drives the bus current-modulator; VOH ≈ VBAT − 0.6 V, VOL ≤ 1.5 V at 1.1 mA sink. Modulation current IMC ≈ 11.5-19.5 mA with RRIS = 100 Ω."+ },+ {+ "number": "9",+ "name": "BAT",+ "type": "power_in",+ "description": "Logic-level reference / battery input. Sets the TX/TXI output high level and RX/RXI input high threshold; VBAT range 2.5-3.8 V (abs max 5.5 V), and must satisfy VBAT(max) ≤ VSTC − 1 V."+ },+ {+ "number": "10",+ "name": "VS",+ "type": "output",+ "description": "Bus/battery supply-mode switch output. Drives an external P-MOSFET (e.g. BSS84) to gate battery supply: pulled to ≈VSTC when VDD is on (bus supply available), high-impedance (≈0.3-1 MΩ) when VDD is off so the battery can take over."+ },+ {+ "number": "11",+ "name": "VDD",+ "type": "power_out",+ "description": "Regulated 3.3 V supply output for the slave/sensor system. VVDD = 3.1-3.4 V at IVDD = 1 mA (VSTC = 6.5 V); output resistance ≈5 Ω at 2-8 mA."+ },+ {+ "number": "12",+ "name": "RX",+ "type": "input",+ "description": "Received data input from the host UART (non-inverted). VIH ≥ VBAT − 0.8 V (up to 5.5 V when VSTC ≥ 6.5 V), VIL ≤ 0.8 V; IRX ≈ −10 to −40 µA at VRX = 0 V."+ },+ {+ "number": "13",+ "name": "RXI",+ "type": "input",+ "description": "Inverted received data input, complementary to RX. Same VIH/VIL thresholds as RX; IRXI ≈ 10-40 µA. Together RX/RXI form the differential control for the transmit modulator."+ },+ {+ "number": "14",+ "name": "RIS",+ "type": "passive",+ "description": "External resistor pin (RRIS) that sets the bus modulation (send) current. RRIS ≥ 100 Ω → IMC ≈ 11.5-19.5 mA; VRIS ≈ 1.4-1.7 V at 100 Ω."+ },+ {+ "number": "15",+ "name": "GND",+ "type": "power_in",+ "description": "Ground reference. All device voltages are referenced to this pin."+ },+ {+ "number": "16",+ "name": "BUSL1",+ "type": "passive",+ "description": "Meter-bus line 1 connection. The other polarity-insensitive M-Bus terminal; typically connected to the bus through a series protection resistor (RL1 ≈ 220 Ω). Absolute-max differential VMB(BUSL2-BUSL1) = ±50 V."+ }+ ],+ "provenance": {+ "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ } }-}+}