← Commit history

Set visibility: public

Ray ·45574a21a6 · ·parent 28b90e2
1 file changed +12−9
page.json+12−9
@@ -32,43 +32,43 @@         "number": "1",         "name": "IN",         "type": "power_in",-        "description": "Regulator supply input (paralleled with pin 2). Requires a typical 4.7\u00b5F bypass capacitor to GND; applications with large load transients may need more input capacitance to prevent input supply droop. Operating range 2.6V to 20V."+        "description": "Regulator supply input (paralleled with pin 2). Requires a typical 4.7µF bypass capacitor to GND; applications with large load transients may need more input capacitance to prevent input supply droop. Operating range 2.6V to 20V."       },       {         "number": "2",         "name": "IN",         "type": "power_in",-        "description": "Regulator supply input (paralleled with pin 1). Tie both IN pins together and bypass with 4.7\u00b5F minimum ceramic to GND. Operating range 2.6V to 20V."+        "description": "Regulator supply input (paralleled with pin 1). Tie both IN pins together and bypass with 4.7µF minimum ceramic to GND. Operating range 2.6V to 20V."       },       {         "number": "3",         "name": "EN/UV",         "type": "input",-        "description": "Enable / undervoltage lockout input. Pulling EN/UV below its threshold puts the part into shutdown (Iq < 1\u00b5A and output disconnected). A resistor divider from IN to EN/UV to GND programs a user UVLO with 1.07V rising threshold and 100mV hysteresis. Tie to IN if unused; do not float. Absolute max \u22120.3V to +22V."+        "description": "Enable / undervoltage lockout input. Pulling EN/UV below its threshold puts the part into shutdown (Iq < 1µA and output disconnected). A resistor divider from IN to EN/UV to GND programs a user UVLO with 1.07V rising threshold and 100mV hysteresis. Tie to IN if unused; do not float. Absolute max −0.3V to +22V."       },       {         "number": "4",         "name": "PG",         "type": "output",-        "description": "Power-good open-drain output. Pulled low when PGFB is below 302mV; goes high-Z (pull-up to logic supply required) when PGFB is above the threshold. Leave floating if power-good indication is not needed. VOL = 16mV @ 100\u00b5A; leakage 0.5\u00b5A max at 20V."+        "description": "Power-good open-drain output. Pulled low when PGFB is below 302mV; goes high-Z (pull-up to logic supply required) when PGFB is above the threshold. Leave floating if power-good indication is not needed. VOL = 16mV @ 100µA; leakage 0.5µA max at 20V."       },       {         "number": "5",         "name": "ILIM",         "type": "bidirectional",-        "description": "Programmable current limit / current monitor. A resistor from ILIM to GND programs the output current limit (scaling factor \u2248128 mA\u00b7k\u03a9; e.g. 649\u03a9 \u2192 ~197mA). Also outputs a 0-300mV signal proportional to load current for monitoring. Tie to GND if not used. Absolute max \u22120.3V to +1V."+        "description": "Programmable current limit / current monitor. A resistor from ILIM to GND programs the output current limit (scaling factor ≈128 mA·kΩ; e.g. 649Ω → ~197mA). Also outputs a 0-300mV signal proportional to load current for monitoring. Tie to GND if not used. Absolute max −0.3V to +1V."       },       {         "number": "6",         "name": "PGFB",         "type": "input",-        "description": "Power-good feedback input. A resistor divider from OUT to PGFB to GND sets the power-good rising threshold: VPG_RISE = 0.305V \u00d7 (1 + RPG2/RPG1) with 43mV hysteresis. PGFB also enables the fast-start circuitry. Tie to IN if power-good/fast-start not used. Input bias 3nA typical."+        "description": "Power-good feedback input. A resistor divider from OUT to PGFB to GND sets the power-good rising threshold: VPG_RISE = 0.305V × (1 + RPG2/RPG1) with 43mV hysteresis. PGFB also enables the fast-start circuitry. Tie to IN if power-good/fast-start not used. Input bias 3nA typical."       },       {         "number": "7",         "name": "SET",         "type": "input",-        "description": "Voltage-set / error-amplifier inverting input. A precision 100\u00b5A reference current flows out of SET into an external resistor to GND, so VOUT = ISET \u00d7 RSET (1.5V to 15V range). Add a capacitor across RSET (typ. 4.7\u00b5F) to reduce output noise and improve PSRR at the cost of start-up time. Use Kelvin connection of the SET resistor ground to load ground. Absolute max \u22120.3V to +16V; SET pin current \u00b110mA max."+        "description": "Voltage-set / error-amplifier inverting input. A precision 100µA reference current flows out of SET into an external resistor to GND, so VOUT = ISET × RSET (1.5V to 15V range). Add a capacitor across RSET (typ. 4.7µF) to reduce output noise and improve PSRR at the cost of start-up time. Use Kelvin connection of the SET resistor ground to load ground. Absolute max −0.3V to +16V; SET pin current ±10mA max."       },       {         "number": "8",@@ -86,7 +86,7 @@         "number": "10",         "name": "OUT",         "type": "power_out",-        "description": "Regulated output (0 to 200mA). Requires a minimum 4.7\u00b5F low-ESR ceramic output capacitor (ESR < 50m\u03a9, ESL < 2nH) for stability. Larger COUT reduces transient droop under fast load steps. Absolute max \u22120.3V to +16V."+        "description": "Regulated output (0 to 200mA). Requires a minimum 4.7µF low-ESR ceramic output capacitor (ESR < 50mΩ, ESL < 2nH) for stability. Larger COUT reduces transient droop under fast load steps. Absolute max −0.3V to +16V."       }     ],     "provenance": {@@ -156,5 +156,8 @@     "docs/gm1200armz-r7-datasheet.pdf",     "viewers/symbol.html",     "viewers/footprint.html"-  ]+  ],+  "visibility": {+    "public": true+  } }\ No newline at end of file