← Commit history

Set visibility: public

Ray ·2fde335cbc · ·parent d1496fa
1 file changed +11−8
page.json+11−8
@@ -32,19 +32,19 @@         "number": "1",         "name": "IN",         "type": "power_in",-        "description": "Regulator supply input. Pins 1 and 2 are tied together internally to IN. Requires a typical 4.7\u00b5F bypass capacitor; large load transients need more input capacitance to prevent supply droop. Input range 2.6V to 20V."+        "description": "Regulator supply input. Pins 1 and 2 are tied together internally to IN. Requires a typical 4.7µF bypass capacitor; large load transients need more input capacitance to prevent supply droop. Input range 2.6V to 20V."       },       {         "number": "2",         "name": "IN",         "type": "power_in",-        "description": "Regulator supply input, paralleled with pin 1. Requires 4.7\u00b5F typical bypass capacitor."+        "description": "Regulator supply input, paralleled with pin 1. Requires 4.7µF typical bypass capacitor."       },       {         "number": "3",         "name": "EN/UV",         "type": "input",-        "description": "Enable / undervoltage-lockout input. Pulling EN/UV low (<1\u00b5A quiescent) places the device in shutdown. A resistor divider between IN, EN/UV, and GND sets a programmable UVLO threshold; rising threshold typically 1.07V with 100mV hysteresis. Tie to IN if not used; do not leave floating."+        "description": "Enable / undervoltage-lockout input. Pulling EN/UV low (<1µA quiescent) places the device in shutdown. A resistor divider between IN, EN/UV, and GND sets a programmable UVLO threshold; rising threshold typically 1.07V with 100mV hysteresis. Tie to IN if not used; do not leave floating."       },       {         "number": "4",@@ -56,19 +56,19 @@         "number": "5",         "name": "ILIM",         "type": "passive",-        "description": "Programmable current-limit input. A resistor from ILIM to GND (Kelvin-connected to the GM1200 GND pin) sets the current limit; programming scale factor is typically 128mA\u00b7k\u03a9. May also serve as a 0V-to-300mV current-monitor output. Tie to GND if programmable limit is not needed."+        "description": "Programmable current-limit input. A resistor from ILIM to GND (Kelvin-connected to the GM1200 GND pin) sets the current limit; programming scale factor is typically 128mA·kΩ. May also serve as a 0V-to-300mV current-monitor output. Tie to GND if programmable limit is not needed."       },       {         "number": "6",         "name": "PGFB",         "type": "input",-        "description": "Power-good feedback input. PG asserts when PGFB rises above 302mV, with 60mV falling hysteresis. External divider between OUT, PGFB, and GND programs the power-good threshold: VPG_thr = 0.305V\u00b7(1 + RPG2/RPG1). PGFB also enables the fast-start-up circuit. Tie to IN if power-good and fast-start are not needed."+        "description": "Power-good feedback input. PG asserts when PGFB rises above 302mV, with 60mV falling hysteresis. External divider between OUT, PGFB, and GND programs the power-good threshold: VPG_thr = 0.305V·(1 + RPG2/RPG1). PGFB also enables the fast-start-up circuit. Tie to IN if power-good and fast-start are not needed."       },       {         "number": "7",         "name": "SET",         "type": "input",-        "description": "Output-voltage setpoint. Inverting input of the error amplifier. Sources a precise 100\u00b5A reference current through an external RSET between SET and GND: VOUT = ISET\u00b7RSET (adjustable 1.5V to 15V). Adding a capacitor from SET to GND reduces output noise, PSRR ripple, and improves transient response at the cost of longer startup. Use Kelvin connection of the RSET ground to the load return for best load regulation."+        "description": "Output-voltage setpoint. Inverting input of the error amplifier. Sources a precise 100µA reference current through an external RSET between SET and GND: VOUT = ISET·RSET (adjustable 1.5V to 15V). Adding a capacitor from SET to GND reduces output noise, PSRR ripple, and improves transient response at the cost of longer startup. Use Kelvin connection of the RSET ground to the load return for best load regulation."       },       {         "number": "8",@@ -86,7 +86,7 @@         "number": "10",         "name": "OUT",         "type": "power_out",-        "description": "Regulated output; supplies load current up to 200mA. Requires a minimum 4.7\u00b5F ceramic output capacitor with ESR < 50m\u03a9 and ESL < 2nH for stability. Larger load transients require more output capacitance to limit peak deviation."+        "description": "Regulated output; supplies load current up to 200mA. Requires a minimum 4.7µF ceramic output capacitor with ESR < 50mΩ and ESL < 2nH for stability. Larger load transients require more output capacitance to limit peak deviation."       },       {         "number": "11",@@ -156,5 +156,8 @@     "docs/gm1200acpz-datasheet.pdf",     "viewers/symbol.html",     "viewers/footprint.html"-  ]+  ],+  "visibility": {+    "public": true+  } }\ No newline at end of file