← Commit history
README.mdadded+76@@ -0,0 +1,76 @@+# GL3224-OIY04++**Genesys Logic** · USB Converters · QFN-32-EP(5x5)++GL3224-OIY04 from Genesys Logic, in a QFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | TXN | output | USB 3.1 Gen 1 SuperSpeed differential transmit negative (SSTX-). |+| 2 | TXP | output | USB 3.1 Gen 1 SuperSpeed differential transmit positive (SSTX+). |+| 3 | AVDD12 | power_in | Analog 1.2 V power source for the USB PHY. Supplied from the on-chip 3.3 V→1.2 V regulator; requires local decoupling. |+| 4 | RXN | input | USB 3.1 Gen 1 SuperSpeed differential receive negative (SSRX-). |+| 5 | RXP | input | USB 3.1 Gen 1 SuperSpeed differential receive positive (SSRX+). |+| 6 | X1 | input | 25 MHz crystal input. Connects to one terminal of an external 25 MHz crystal or accepts an external 25 MHz clock. |+| 7 | X2 | bidirectional | 25 MHz crystal output/feedback. Connects to the second terminal of the external 25 MHz crystal. |+| 8 | AVDD33 | power_in | Analog 3.3 V power source for the USB PHY. Decouple locally to GND. |+| 9 | RTERM | passive | USB reference resistor. Sets the USB drive/termination level; tie to GND through a 680 Ω 1% reference resistor (RREF) laid between RTERM and GND. |+| 10 | SPI_MISO | input | SPI interface: master-in / slave-out from the external SPI flash holding firmware. |+| 11 | SPI_MOSI | output | SPI interface: master-out / slave-in to the external SPI flash holding firmware. |+| 12 | SPI_CK | output | SPI interface clock driven to the external SPI flash. |+| 13 | SPI_CS | output | SPI interface chip select (active-low) to the external SPI flash. |+| 14 | LED | output | Memory card access indicator LED driver output. Programmable behavior; can also be repurposed as a read-only status option. |+| 15 | VBUS | power_in | 5 V power source from the USB VBUS rail. Feeds the on-chip 5 V→3.3 V regulator. |+| 16 | DVDD33 | power_in | Digital 3.3 V power source for the core digital I/O. Decouple locally to GND. |+| 17 | DVDD12 | power_in | Digital 1.2 V power source for the core logic. Supplied from the on-chip 3.3 V→1.2 V regulator. |+| 18 | SD_D1 | bidirectional | SD/MMC card data bit 1 (memory card interface). |+| 19 | SD_D0 | bidirectional | SD/MMC card data bit 0 (memory card interface). |+| 20 | SD_CK | output | SD/MMC card clock output driven to the memory card. |+| 21 | SD_CM | bidirectional | SD/MMC card command/response line. Has an internal pull-up when configured as input. |+| 22 | SD_D3 | bidirectional | SD/MMC card data bit 3 (memory card interface). |+| 23 | SD_D2 | bidirectional | SD/MMC card data bit 2 (memory card interface). |+| 24 | VUHSI | power_out | SD 3.0 UHS-I IO pad power rail. Sourced from the GL3224 internal regulator; no external power input is required, only local decoupling. |+| 25 | DVDD33 | power_in | Digital 3.3 V power source (second DVDD33 pin). Tie together with pin 16. |+| 26 | SD_VCC | power_out | SD card VCC output. Driven through the on-chip power MOSFET to supply the SD/MMC card socket. |+| 27 | GND | power_in | Device ground. The exposed die pad on the QFN underside must also be soldered to ground. |+| 28 | SD_WP | input | SD write-protect sense input. 0 = write enable, 1 = write protected. Internal pull-up when input. |+| 29 | SD_CDZ | input | SD card-detect input (active-low). 0 = card inserted, 1 = no card. Internal pull-up when input. |+| 30 | AVDD33 | power_in | Analog 3.3 V power source (second AVDD33 pin). Tie together with pin 8 and decouple locally. |+| 31 | DM | bidirectional | USB 2.0 high-speed / full-speed differential data minus (D-). |+| 32 | DP | bidirectional | USB 2.0 high-speed / full-speed differential data plus (D+). |+| EP | GND | power_in | Exposed die pad on the QFN underside. Must be connected to system ground for electrical return and thermal dissipation. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Genesys Logic |+| Package | QFN-32-EP(5x5) |+| Category | Interface |+| Pins | 33 |++## Ordering variants++Same part, different packaging or reel option.++- `GL3224-OIY04OIYXX`+- `GL3224-OIY04`+- `GL3224-OIY04ONYXX`++## CAD (KiCad official)++- Symbol: `GL3224-OIY04`+- Footprint: `Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm`+- 3D model: QFN-32-EP(5x5) (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Genesys Logic datasheet](docs/gl3224-oiy04-datasheet.pdf) (25 pp, sha256 `d31d18e13a3e5160`, retrieved 2026-08-17, tier: lcsc)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/gl3224-oiy04-datasheet.pdf)
page.jsonadded+34@@ -0,0 +1,34 @@+{+ "slug": "gl3224-oiy04",+ "version": "0.1.0",+ "type": "component",+ "description": "Genesys Logic USB Converters, QFN-32-EP(5x5). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "interface",+ "gl3224-oiy04"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "gl3224-oiy04.kicad_sym",+ "gl3224-oiy04.kicad_mod",+ "gl3224-oiy04.glb",+ "gl3224-oiy04.step",+ "gl3224-oiy04.lbr",+ "docs/hero.png",+ "docs/gl3224-oiy04-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ],+ "visibility": "public",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}