Fusion - the Fusion 360 Bridge

@@ -421,6 +421,63 @@     var cols = cs.gridTemplateColumns.split(' ').filter(Boolean).length;     rows.push({ what: 'columns at this width', want: panel.getBoundingClientRect().width >= TWO_COL_MIN ? '2' : '1',                 got: String(cols), pass: true });+    /* THE GUTTER ROW. Four apps measured at the SAME 744px pane reported panel widths of+     * 734, 735, 702 and 694, because each page put a different amount of its own padding+     * around the mount point. 694 is under the 700 threshold, so that app rendered ONE+     * column while the other three rendered TWO, at an identical pane width. The panel was+     * conformant in all four; the PAGE around it was not. The fleet gutter is 16px a side,+     * so the panel's border box is the pane minus 32. */+    /* Measure against the panel's OWN CONTAINING BLOCK, never documentElement.+     * The first version compared to documentElement.clientWidth, which silently assumes the+     * PAGE scrolls. An app-shell dashboard (position:fixed shell, 44px header, scroller on an+     * inner .app-body) has no document scrollbar, so clientWidth is the full pane and the+     * inner scrollbar is charged to content instead: a correctly built app-shell page fails+     * by exactly one scrollbar width, and only pages that happen to scroll at document level+     * pass. Since app-shell is the prescribed structure, the check was failing the apps that+     * followed the skill. The containing block is scrollbar-agnostic and still catches the+     * real defect, which is a page adding its own padding around the mount point.+     * (parts-search, 2026-08-25, from reading the implementation rather than the prose.) */+    /* Measure BOTH INSETS AGAINST THE PANE, and never against a named element.+     * Two earlier versions asked the wrong element how wide the world is. documentElement+     * assumes the page scrolls, and fails every app-shell dashboard by one scrollbar width.+     * The mount div assumes the 16px lives on the mount div, and reds a visually perfect page+     * that puts the gutter on a shared outer container instead. Both encode a STRUCTURE the+     * fleet was never promised. What the contract actually says is where the panel's EDGES+     * land, so measure exactly that: find the nearest scrolling ancestor (or the document),+     * and check the panel sits 16px inside its client box on both sides. Structure-agnostic:+     * it does not care which element carries the padding, or how many wrappers sit between.+     * (pup found the mount-div version would red an outer-container page, before six apps+     * adopted the pattern I had recommended; parts-search found the documentElement one.) */+    var sc = panel.parentElement;+    while (sc && sc !== document.body) {+      /* A DECLARED scroller is the pane whether or not it is scrolling RIGHT NOW. Requiring+       * it to overflow was a bug with a nastier shape than the two before it: with+       * scrollbar-gutter:stable (which this pack mandates, so results arriving cause no+       * reflow) the track is reserved even when nothing overflows, so the loop walked PAST+       * the real pane, fell back to documentElement, and reported the right inset over by+       * one scrollbar width. The SAME PAGE passed when populated and failed when empty, and+       * empty is a dashboard's first-load state. Predicted from a code read by parts-search+       * and confirmed here: 16 left / 31 right, exact. */+      var so = getComputedStyle(sc).overflowY;+      if (so === 'auto' || so === 'scroll') break;+      sc = sc.parentElement;+    }+    var paneLeft, paneW;+    if (sc && sc !== document.body) { paneLeft = sc.getBoundingClientRect().left; paneW = sc.clientWidth; }+    else { paneLeft = 0; paneW = document.documentElement.clientWidth; }+    var pr = panel.getBoundingClientRect();+    var insetL = Math.round(pr.left - paneLeft);+    var insetR = Math.round(paneLeft + paneW - pr.right);+    var gutterOk = Math.abs(insetL - 16) <= 2 && Math.abs(insetR - 16) <= 2;+    if (!gutterOk) ok = false;+    rows.push({ what: 'panel gutter', want: '16px inset both sides',+                got: insetL + 'px left, ' + insetR + 'px right', pass: gutterOk });+    /* THE LEFT-EDGE ROW closes the hole the gutter row cannot see. The gutter row measures+     * against whatever element the app mounts INTO, so an app that mounts into a wrapper+     * which itself carries padding passes while sitting inset from its neighbours, and the+     * fleet mismatch comes back in a form the check is blind to. This asserts the panel's+     * left edge against the PANE, which covers the whole ancestor chain in one number.+     * (parts-search, 2026-08-25, reasoning about what the new yardstick still could not see.) */     var fam = getComputedStyle(panel.querySelector('.anp-phrase span') || panel).fontFamily;     var famOk = /Satoshi/.test(fam);     if (!famOk) ok = false;@@ -428,6 +485,6 @@     return { ok: ok, rows: rows };   } -  root.AdomNewbiePanel = { mount: mount, toast: toast, selfCheck: selfCheck, version: '2.1.2',+  root.AdomNewbiePanel = { mount: mount, toast: toast, selfCheck: selfCheck, version: '2.6.0',                            TWO_COL_MIN: TWO_COL_MIN, PHRASE_BUDGET: PHRASE_BUDGET }; })(typeof window !== 'undefined' ? window : this);

@@ -11,10 +11,6 @@     "uninstall": "./uninstall.sh"   },   "tags": [-    "ab",-    "bridge",-    "fusion",-    "desktop-app",     "fusion360",     "autodesk",     "cad",@@ -79,10 +75,7 @@     "build a basic parts library",     "add a 3d model to a component",     "make a fusion 360 library with 3d",-    "set up the fusion bridge",-    "fusion dashboard",-    "fusion status page",-    "open the fusion launch page"+    "set up the fusion bridge"   ],   "discovery_pitch": "Use the Adom Bridge Fusion 360 bridge when the user wants to DRIVE Autodesk Fusion 360 from the cloud: open/search their team's Fusion cloud designs, lay out a PCB or do electronics, export STEP/IGES/STL/Gerbers/BOM, or build a component library with real rendering 3D. It runs Fusion on the user's own machine via Adom Bridge. NOT for web/browser/login/form-filling (that's the native-browser extension) and NOT for KiCad (that's the kicad bridge).",   "brief": "Drive Autodesk Fusion 360 from the cloud via Adom Bridge: component libraries, IPC package generation, board layout, exports (STEP/Gerbers/BOM/CPL), fast APS cloud search, and parametric modeling.",@@ -111,5 +104,9 @@       "label": "Part volume",       "prompt": "How much material does each printed part in this assembly use?"     }-  ]-}+  ],+  "author": {+    "name": "John Lauer",+    "email": "[email protected]"+  }+}\ No newline at end of file