← Commit history

Initial commit: component/ft232rq-reel

Ray ·dea450a9ca ·
2 files changed +108
README.mdadded+74
@@ -0,0 +1,74 @@+# FT232RQ-REEL++**FTDI** · USB Converters · QFN-32-EP(5x5)++FT232RQ-REEL from FTDI, in a QFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VCCIO | power_in | +1.8 V to +5.25 V supply for the UART interface and CBUS group pins. Tie to 3V3OUT for 3.3 V I/O or to VCC for +5 V CMOS I/O; may also be supplied from an external +1.8 V to +2.8 V rail sourced from the same supply as VCC. |+| 2 | RXD | input | Receiving asynchronous data input. |+| 3 | RI# | input | Ring Indicator control input. When remote wake-up is enabled in EEPROM, driving RI# low (20 ms active-low pulse) resumes the USB host from suspend. |+| 4 | GND | power_in | Device digital ground supply pin. |+| 5 | NC | unconnected | No internal connection. Do not connect. |+| 6 | DSR# | input | Data Set Ready control input / handshake signal. |+| 7 | DCD# | input | Data Carrier Detect control input. |+| 8 | CTS# | input | Clear To Send control input / handshake signal. |+| 9 | CBUS4 | output | Configurable CBUS output-only pin. EEPROM-configurable; factory default is SLEEP#. Available options include TXDEN, PWREN#, TXLED#, RXLED#, TX&RXLED#, SLEEP#, CLK48/24/12/6. |+| 10 | CBUS2 | bidirectional | Configurable CBUS I/O pin. EEPROM-configurable; factory default is TXDEN. Options include TXDEN, PWREN#, TXLED#, RXLED#, TX&RXLED#, SLEEP#, CLKx, CBitBangI/O, BitBangWRn, BitBangRDn. |+| 11 | CBUS3 | bidirectional | Configurable CBUS I/O pin. EEPROM-configurable; factory default is PWREN# (requires 10 kΩ pull-up to VCCIO). |+| 12 | NC | unconnected | No internal connection. Do not connect. |+| 13 | NC | unconnected | No internal connection. Do not connect. |+| 14 | USBDP | bidirectional | USB D+ data signal. Incorporates internal series resistor and 1.5 kΩ pull-up to +3.3 V for Full-Speed identification. |+| 15 | USBDM | bidirectional | USB D- data signal. Incorporates internal series resistor. |+| 16 | 3V3OUT | power_out | +3.3 V output from the integrated LDO regulator; decouple to ground with a 100 nF capacitor. Supplies the internal USB transceiver and USBDP pull-up; up to 50 mA available for external logic and may also feed VCCIO. |+| 17 | GND | power_in | Device digital ground supply pin. |+| 18 | RESET# | input | Active-low reset input. Can be driven by an external device to reset the FT232R; leave unconnected or pull up to VCC if unused. |+| 19 | VCC | power_in | +3.3 V to +5.25 V supply to the device core. Minimum operating voltage is +4.0 V when using the internal clock generator; +3.3 V operation is possible when driven by an external crystal oscillator. |+| 20 | GND | power_in | Device digital ground supply pin. |+| 21 | CBUS1 | bidirectional | Configurable CBUS I/O pin. EEPROM-configurable; factory default is RXLED#. |+| 22 | CBUS0 | bidirectional | Configurable CBUS I/O pin. EEPROM-configurable; factory default is TXLED#. |+| 23 | NC | unconnected | No internal connection. Do not connect. |+| 24 | AGND | power_in | Device analogue ground supply for the internal clock multiplier. |+| 25 | NC | unconnected | No internal connection. Do not connect. |+| 26 | TEST | input | IC test-mode enable. Must be tied to GND for normal operation, otherwise the device will appear to fail. |+| 27 | OSCI | input | 12 MHz oscillator cell input. Optional; leave unconnected for normal operation with the internal oscillator. Used with an external crystal, ceramic resonator, or oscillator. |+| 28 | OSCO | output | 12 MHz oscillator cell output. Optional; leave unconnected for normal operation with the internal oscillator. |+| 29 | NC | unconnected | No internal connection. Do not connect. |+| 30 | TXD | output | Transmit asynchronous data output. |+| 31 | DTR# | output | Data Terminal Ready control output / handshake signal. |+| 32 | RTS# | output | Request To Send control output / handshake signal. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | FTDI |+| Package | QFN-32-EP(5x5) |+| Category | Interface |+| Pins | 32 |++## Ordering variants++- `FT232RQ-Reel`+- `FT232RQ-REELFT232RQ-Tray`+- `FT232RQ-REELFT232RL-Reel`+- `FT232RQ-REELFT232RL-Tube`++## CAD (KiCad official)++- Symbol: `FT232RQ-REEL`+- Footprint: `Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm`+- 3D model: QFN-32-EP(5x5) (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [FTDI datasheet](docs/ft232rq-reel-datasheet.pdf) (47 pp, sha256 `436f260dbc99dcab`, retrieved 2026-08-17, tier: lcsc)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/ft232rq-reel-datasheet.pdf)
page.jsonadded+34
@@ -0,0 +1,34 @@+{+  "slug": "ft232rq-reel",+  "version": "0.1.0",+  "type": "component",+  "description": "FTDI USB Converters, QFN-32-EP(5x5). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "interface",+    "ft232rq-reel"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "ft232rq-reel.kicad_sym",+    "ft232rq-reel.kicad_mod",+    "ft232rq-reel.glb",+    "ft232rq-reel.step",+    "ft232rq-reel.lbr",+    "docs/hero.png",+    "docs/ft232rq-reel-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "visibility": "public",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file