component
FT232HL-REEL
Public Made by Adomby adom
FTDI USB Converters, LQFP-48(7x7). Pinout extracted from the datasheet, KiCad symbol/footprint/3D.
← Commit history
page.json+13−10@@ -56,7 +56,7 @@ "number": "5", "name": "REF", "type": "passive",- "description": "Analog current reference. Connect a 12K\u03a9 1% resistor from this pin to GND to set the internal bias current."+ "description": "Analog current reference. Connect a 12KΩ 1% resistor from this pin to GND to set the internal bias current." }, { "number": "6",@@ -152,7 +152,7 @@ "number": "21", "name": "ACBUS0", "type": "bidirectional",- "description": "Configurable ACBUS I/O pin. Default TXDEN (RS485 driver enable) when EEPROM sets that option, otherwise TriState with 75K\u03a9 pull-up to VCCIO. EEPROM-selectable to PWREN#, TXLED#, RXLED#, TX&RXLED#, SLEEP#, CLK30/15/7.5, DRIVE0/1 (see Table 3.5)."+ "description": "Configurable ACBUS I/O pin. Default TXDEN (RS485 driver enable) when EEPROM sets that option, otherwise TriState with 75KΩ pull-up to VCCIO. EEPROM-selectable to PWREN#, TXLED#, RXLED#, TX&RXLED#, SLEEP#, CLK30/15/7.5, DRIVE0/1 (see Table 3.5)." }, { "number": "22",@@ -176,13 +176,13 @@ "number": "25", "name": "ACBUS1", "type": "bidirectional",- "description": "Configurable ACBUS I/O pin. Default tri-state input with 75K\u03a9 pull-up to VCCIO; commonly used for TXE#, WRSTB#, GPIOH1, A0 (CPU FIFO) or SS_n (FT1248). EEPROM-selectable to any ACBUS signal in Table 3.5."+ "description": "Configurable ACBUS I/O pin. Default tri-state input with 75KΩ pull-up to VCCIO; commonly used for TXE#, WRSTB#, GPIOH1, A0 (CPU FIFO) or SS_n (FT1248). EEPROM-selectable to any ACBUS signal in Table 3.5." }, { "number": "26", "name": "ACBUS2", "type": "bidirectional",- "description": "Configurable ACBUS I/O pin. Default tri-state input with 75K\u03a9 pull-up to VCCIO; RD#, RDSTB#, GPIOH2 or MISO (FT1248) in the various modes. EEPROM-selectable to any ACBUS signal in Table 3.5."+ "description": "Configurable ACBUS I/O pin. Default tri-state input with 75KΩ pull-up to VCCIO; RD#, RDSTB#, GPIOH2 or MISO (FT1248) in the various modes. EEPROM-selectable to any ACBUS signal in Table 3.5." }, { "number": "27",@@ -212,25 +212,25 @@ "number": "31", "name": "ACBUS7", "type": "bidirectional",- "description": "Configurable ACBUS I/O pin. Default PWRSAV# / PWRSAV# in most modes, or WRSAV# (UART) / GPIOH7 (MPSSE). Defaults to GPIO line with an internal 75K\u03a9 pull-down to GND (can be switched to USBVCC mode via EEPROM)."+ "description": "Configurable ACBUS I/O pin. Default PWRSAV# / PWRSAV# in most modes, or WRSAV# (UART) / GPIOH7 (MPSSE). Defaults to GPIO line with an internal 75KΩ pull-down to GND (can be switched to USBVCC mode via EEPROM)." }, { "number": "32", "name": "ACBUS8", "type": "bidirectional",- "description": "Configurable ACBUS I/O pin. Default tri-state input with 75K\u03a9 pull-up to VCCIO; EEPROM-selectable to any ACBUS signal in Table 3.5 (bit-bang capable)."+ "description": "Configurable ACBUS I/O pin. Default tri-state input with 75KΩ pull-up to VCCIO; EEPROM-selectable to any ACBUS signal in Table 3.5 (bit-bang capable)." }, { "number": "33", "name": "ACBUS9", "type": "bidirectional",- "description": "Configurable ACBUS I/O pin. Default tri-state input with 75K\u03a9 pull-up to VCCIO; EEPROM-selectable to any ACBUS signal in Table 3.5 (bit-bang capable)."+ "description": "Configurable ACBUS I/O pin. Default tri-state input with 75KΩ pull-up to VCCIO; EEPROM-selectable to any ACBUS signal in Table 3.5 (bit-bang capable)." }, { "number": "34", "name": "RESET#", "type": "input",- "description": "Chip reset input, active low. Tie to VCCIO through a pull-up (typically 10K\u03a9) or leave high for normal operation."+ "description": "Chip reset input, active low. Tie to VCCIO through a pull-up (typically 10KΩ) or leave high for normal operation." }, { "number": "35",@@ -284,7 +284,7 @@ "number": "43", "name": "EEDATA", "type": "bidirectional",- "description": "Serial data to/from the external 93C46/93C56/93C66 EEPROM. Connect directly to the EEPROM DI pin AND to DO through a 2.2K\u03a9 series resistor; also pull DO up to VCCD with 10K\u03a9. Tri-stated during device reset."+ "description": "Serial data to/from the external 93C46/93C56/93C66 EEPROM. Connect directly to the EEPROM DI pin AND to DO through a 2.2KΩ series resistor; also pull DO up to VCCD with 10KΩ. Tri-stated during device reset." }, { "number": "44",@@ -396,5 +396,8 @@ "docs/ft232hl-reel-datasheet.pdf", "viewers/symbol.html", "viewers/footprint.html"- ]+ ],+ "visibility": {+ "public": true+ } }