component
FSV9522
Public Made by Adomby adom
Forsinve RFID ICs, QFN-32(5x5). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+69@@ -0,0 +1,69 @@+# FSV9522++**Forsinve** · RFID ICs · QFN-32(5x5)++FSV9522 from Forsinve, in a QFN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | I2C | input | I2C-bus enable input for selecting I2C interface mode |+| 2 | PVDD | power_in | Pin power supply, 1.6 to 3.6 V |+| 3 | DVDD | power_in | Digital power supply, 2.5 to 3.6 V |+| 4 | DVSS | power_in | Digital ground |+| 5 | PVSS | power_in | Pin power supply ground |+| 6 | NRSTPD | input | Reset and power-down input; power-down when LOW with oscillator disabled, reset enabled by positive edge |+| 7 | MFIN | input | MIFARE signal input for external antenna interface |+| 8 | MFOUT | output | MIFARE signal output for external active antenna interface |+| 9 | SVDD | power_in | MFIN and MFOUT pin power supply, 1.6 to 3.6 V |+| 10 | TVSS | power_in | Transmitter output stage 1 ground |+| 11 | TX1 | output | Transmitter 1 modulated 13.56 MHz carrier output for antenna driver |+| 12 | TVDD | power_in | Transmitter power supply for TX drivers, 2.5 to 3.6 V |+| 13 | TX2 | output | Transmitter 2 modulated 13.56 MHz carrier output for antenna driver |+| 14 | TVSS | power_in | Transmitter output stage 2 ground |+| 15 | AVDD | power_in | Analog power supply, 2.5 to 3.6 V |+| 16 | VMID | power_in | Internal analog reference voltage for demodulator |+| 17 | RX | input | RF signal input for Manchester encoded receive from ISO/IEC 14443 A cards |+| 18 | AVSS | power_in | Analog ground |+| 19 | AUX1 | output | Auxiliary test output; outputs test signals, DAC values, or signal conditions |+| 20 | AUX2 | output | Auxiliary test output; outputs test signals, DAC values, or signal conditions |+| 21 | OSCIN | input | Crystal oscillator inverting amplifier input or external 27.12 MHz clock input |+| 22 | OSCOUT | output | Crystal oscillator inverting amplifier output for crystal connection |+| 23 | IRQ | output | Interrupt request output; indicates interrupt events with configurable polarity and push-pull mode |+| 24 | SDA/NSS/RX | bidirectional | Multi-function interface pin: I2C SDA (I/O), SPI slave select NSS (I), or UART receive RX (I) depending on detected interface mode |+| 25 | D1/ADR_5 | bidirectional | Multi-function pin: test port D1 (I/O) or I2C-bus address 5 input/output |+| 26 | D2/ADR_4 | bidirectional | Multi-function pin: test port D2 (I/O) or I2C-bus address 4 input |+| 27 | D3/ADR_3 | bidirectional | Multi-function pin: test port D3 (I/O) or I2C-bus address 3 input |+| 28 | D4/ADR_2 | bidirectional | Multi-function pin: test port D4 (I/O) or I2C-bus address 2 input |+| 29 | D5/ADR_1/SCK/DTRQ | bidirectional | Multi-function pin: test port D5 (I/O), I2C address 1 (I/O), SPI serial clock SCK (I), or UART request to send DTRQ (O) |+| 30 | D6/ADR_0/MOSI/MX | bidirectional | Multi-function pin: test port D6 (I/O), I2C address 0 input, SPI master out slave in MOSI (I/O), or UART output MX (O) |+| 31 | D7/SCL/MISO/TX | bidirectional | Multi-function pin: test port D7 (I/O), I2C serial clock SCL (I/O), SPI master in slave out MISO (I/O), or UART transmit TX (O) |+| 32 | EA | input | External I2C-bus address configuration input; address latched immediately after reset release |+| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Forsinve |+| Package | QFN-32(5x5) |+| Category | RF And Wireless |+| Pins | 33 |++## CAD (KiCad official)++- Symbol: `FSV9522`+- Footprint: `Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm`+- 3D model: QFN-32(5x5) (KiCad packages3D, STEP)+- 3D model files: `fsv9522-etched.step` / `fsv9522-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `fsv9522.step` / `fsv9522.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Forsinve datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8590903479076937728) (88 pp, sha256 `ba24952fcfc87247`, retrieved 2026-09-22, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/fsv9522-datasheet.pdf)
page.jsonadded+294@@ -0,0 +1,294 @@+{+ "slug": "fsv9522",+ "version": "0.1.0",+ "type": "component",+ "description": "Forsinve RFID ICs, QFN-32(5x5). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "rf and wireless",+ "fsv9522",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "fsv9522.kicad_sym",+ "fsv9522.kicad_mod",+ "fsv9522.glb",+ "fsv9522.step",+ "fsv9522.lbr",+ "docs/hero.png",+ "docs/fsv9522-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ],+ "component": {+ "mpn": "FSV9522",+ "manufacturer": "Forsinve",+ "package": "QFN-32(5x5)",+ "pin_count": 33,+ "category": "RF And Wireless",+ "subcategory": "RFID ICs",+ "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8590903479076937728",+ "parts": {+ "symbol": "fsv9522.kicad_sym",+ "footprint": "fsv9522.kicad_mod",+ "model_3d": "fsv9522-etched.glb",+ "model_3d_plain": "fsv9522.glb",+ "model_3d_step": "fsv9522-etched.step",+ "model_3d_step_plain": "fsv9522.step",+ "lbr": "fsv9522.lbr"+ },+ "distributor_links": {+ "lcsc": "C5336460"+ },+ "pins": [+ {+ "number": "1",+ "name": "I2C",+ "type": "input",+ "description": "I2C-bus enable input for selecting I2C interface mode"+ },+ {+ "number": "2",+ "name": "PVDD",+ "type": "power_in",+ "description": "Pin power supply, 1.6 to 3.6 V"+ },+ {+ "number": "3",+ "name": "DVDD",+ "type": "power_in",+ "description": "Digital power supply, 2.5 to 3.6 V"+ },+ {+ "number": "4",+ "name": "DVSS",+ "type": "power_in",+ "description": "Digital ground"+ },+ {+ "number": "5",+ "name": "PVSS",+ "type": "power_in",+ "description": "Pin power supply ground"+ },+ {+ "number": "6",+ "name": "NRSTPD",+ "type": "input",+ "description": "Reset and power-down input; power-down when LOW with oscillator disabled, reset enabled by positive edge"+ },+ {+ "number": "7",+ "name": "MFIN",+ "type": "input",+ "description": "MIFARE signal input for external antenna interface"+ },+ {+ "number": "8",+ "name": "MFOUT",+ "type": "output",+ "description": "MIFARE signal output for external active antenna interface"+ },+ {+ "number": "9",+ "name": "SVDD",+ "type": "power_in",+ "description": "MFIN and MFOUT pin power supply, 1.6 to 3.6 V"+ },+ {+ "number": "10",+ "name": "TVSS",+ "type": "power_in",+ "description": "Transmitter output stage 1 ground"+ },+ {+ "number": "11",+ "name": "TX1",+ "type": "output",+ "description": "Transmitter 1 modulated 13.56 MHz carrier output for antenna driver"+ },+ {+ "number": "12",+ "name": "TVDD",+ "type": "power_in",+ "description": "Transmitter power supply for TX drivers, 2.5 to 3.6 V"+ },+ {+ "number": "13",+ "name": "TX2",+ "type": "output",+ "description": "Transmitter 2 modulated 13.56 MHz carrier output for antenna driver"+ },+ {+ "number": "14",+ "name": "TVSS",+ "type": "power_in",+ "description": "Transmitter output stage 2 ground"+ },+ {+ "number": "15",+ "name": "AVDD",+ "type": "power_in",+ "description": "Analog power supply, 2.5 to 3.6 V"+ },+ {+ "number": "16",+ "name": "VMID",+ "type": "power_in",+ "description": "Internal analog reference voltage for demodulator"+ },+ {+ "number": "17",+ "name": "RX",+ "type": "input",+ "description": "RF signal input for Manchester encoded receive from ISO/IEC 14443 A cards"+ },+ {+ "number": "18",+ "name": "AVSS",+ "type": "power_in",+ "description": "Analog ground"+ },+ {+ "number": "19",+ "name": "AUX1",+ "type": "output",+ "description": "Auxiliary test output; outputs test signals, DAC values, or signal conditions"+ },+ {+ "number": "20",+ "name": "AUX2",+ "type": "output",+ "description": "Auxiliary test output; outputs test signals, DAC values, or signal conditions"+ },+ {+ "number": "21",+ "name": "OSCIN",+ "type": "input",+ "description": "Crystal oscillator inverting amplifier input or external 27.12 MHz clock input"+ },+ {+ "number": "22",+ "name": "OSCOUT",+ "type": "output",+ "description": "Crystal oscillator inverting amplifier output for crystal connection"+ },+ {+ "number": "23",+ "name": "IRQ",+ "type": "output",+ "description": "Interrupt request output; indicates interrupt events with configurable polarity and push-pull mode"+ },+ {+ "number": "24",+ "name": "SDA/NSS/RX",+ "type": "bidirectional",+ "description": "Multi-function interface pin: I2C SDA (I/O), SPI slave select NSS (I), or UART receive RX (I) depending on detected interface mode"+ },+ {+ "number": "25",+ "name": "D1/ADR_5",+ "type": "bidirectional",+ "description": "Multi-function pin: test port D1 (I/O) or I2C-bus address 5 input/output"+ },+ {+ "number": "26",+ "name": "D2/ADR_4",+ "type": "bidirectional",+ "description": "Multi-function pin: test port D2 (I/O) or I2C-bus address 4 input"+ },+ {+ "number": "27",+ "name": "D3/ADR_3",+ "type": "bidirectional",+ "description": "Multi-function pin: test port D3 (I/O) or I2C-bus address 3 input"+ },+ {+ "number": "28",+ "name": "D4/ADR_2",+ "type": "bidirectional",+ "description": "Multi-function pin: test port D4 (I/O) or I2C-bus address 2 input"+ },+ {+ "number": "29",+ "name": "D5/ADR_1/SCK/DTRQ",+ "type": "bidirectional",+ "description": "Multi-function pin: test port D5 (I/O), I2C address 1 (I/O), SPI serial clock SCK (I), or UART request to send DTRQ (O)"+ },+ {+ "number": "30",+ "name": "D6/ADR_0/MOSI/MX",+ "type": "bidirectional",+ "description": "Multi-function pin: test port D6 (I/O), I2C address 0 input, SPI master out slave in MOSI (I/O), or UART output MX (O)"+ },+ {+ "number": "31",+ "name": "D7/SCL/MISO/TX",+ "type": "bidirectional",+ "description": "Multi-function pin: test port D7 (I/O), I2C serial clock SCL (I/O), SPI master in slave out MISO (I/O), or UART transmit TX (O)"+ },+ {+ "number": "32",+ "name": "EA",+ "type": "input",+ "description": "External I2C-bus address configuration input; address latched immediately after reset release"+ },+ {+ "number": "33",+ "name": "EP",+ "type": "passive",+ "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.2",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.2",+ "primary_model": "claude-haiku-4-5-20251001",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-4-6",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: Pins 24-31 are multi-function pins with interface-dependent electrical characteristics. Pin 24 (SDA/",+ "exposed pad 33 added from the footprint"+ ],+ "pages_sent": 88,+ "cost_usd": 0.6343,+ "at": "2026-09-22T05:56:11"+ },+ "datasheet": {+ "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8590903479076937728",+ "pages": 88,+ "sha256": "ba24952fcfc87247",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 33,+ "described": 33,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ }+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}