component
FSV9520
Public Made by Adomby adom
Forsinve RFID ICs, QFN-32(5x5). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+70@@ -0,0 +1,70 @@+# FSV9520++**Forsinve** · RFID ICs · QFN-32(5x5)++FSV9520 from Forsinve, in a QFN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | SPI | power_in | Connects to digital ground (DVSS) per pin table description; labeling inconsistency noted |+| 2 | PVDD | power_in | Pin power supply voltage, range 1.6V to 3.6V per Table 1 fast reference data |+| 3 | DVDD | power_in | Digital power supply voltage, range 2.5V to 3.6V per Table 1 fast reference data |+| 4 | DVSS | power_in | Digital ground per pin table; does not require connection to heat sink |+| 5 | PVSS | power_in | Pin power ground |+| 6 | NRSTPD | input | Reset and power-down input; low level triggers power-down with internal drain current shutdown and oscillator stop, rising edge triggers reset |+| 7 | MFIN | input | MIFARE signal input for analog module interface with internal pull-up/pull-down characteristics |+| 8 | MFOUT | output | MIFARE signal output from analog module with output current 4mA maximum at 3V |+| 9 | SVDD | power_in | Power supply for MFIN and MFOUT pins, range 1.6V to 3.6V per Table 1 |+| 10 | TVSS | power_in | Transmitter power ground |+| 11 | TX1 | output | Antenna driver output pin; outputs 13.56MHz modulated energy carrier with maximum IDD(TVDD) up to 100mA |+| 12 | TVDD | power_in | Transmitter power supply voltage, range 2.5V to 3.6V per Table 1 |+| 13 | TX2 | output | Antenna driver output pin; outputs 13.56MHz modulated energy carrier for complementary drive configuration |+| 14 | TVSS | power_in | Transmitter power ground |+| 15 | AVDD | power_in | Analog power supply voltage, range 2.5V to 3.6V per Table 1; must equal VDDA and VDD(TVDD) |+| 16 | VMID | power_in | Internal reference voltage for analog circuitry biasing and signal processing |+| 17 | RX | input | RF signal input for receiving modulated signals from transponders; input impedance 350Ω, input capacitance 10pF, voltage range ±1V around VDDA with Manchester encoded minimum 5mV at 48dB gain |+| 18 | AVSS | power_in | Analog power ground |+| 19 | AUX1 | output | Auxiliary test output for monitoring internal signals; current source output recommended with 1kΩ pull-down resistor, maximum 4mA |+| 20 | AUX2 | output | Auxiliary test output for monitoring internal signals; current source output recommended with 1kΩ pull-down resistor, maximum 4mA |+| 21 | OSCIN | input | Crystal oscillator buffer input for 27.12MHz crystal or external clock signal; input capacitance 2pF, voltage threshold 0.7VDDA high and 0.3VDDA low |+| 22 | OSCOUT | output | Crystal oscillator buffer output; drives 27.12MHz crystal oscillator or provides clock output |+| 23 | IRQ | output | Interrupt request output; can be configured as push-pull CMOS output or open-drain output via Diverge register; indicates interrupt events from multiple sources |+| 24 | NSS | input | SPI chip select input (active low) for Serial Peripheral Interface control; supports up to 10Mbps SPI data rate |+| 25 | D1 | bidirectional | Test pin for general purpose test and diagnostic functions; note: function conflicts with footnote [2] references |+| 26 | D2 | bidirectional | Test pin for general purpose test and diagnostic functions |+| 27 | D3 | bidirectional | Test pin for general purpose test and diagnostic functions |+| 28 | D4 | bidirectional | Test pin for general purpose test and diagnostic functions |+| 29 | D5 | bidirectional | Test pin for diagnostic functions; also functions as SCK (SPI clock input) in SPI mode for serial data synchronization |+| 30 | D6 | bidirectional | Test pin for diagnostic functions; also functions as MOSI (SPI master output slave input) in SPI mode for host to device data transfer |+| 31 | D7 | bidirectional | Test pin for diagnostic functions; also functions as MISO (SPI master input slave output) in SPI mode for device to host data transfer |+| 32 | EA | power_in | Connects to digital power supply (DVDD) per pin table description; labeling inconsistency noted similar to pin 1 |+| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Forsinve |+| Package | QFN-32(5x5) |+| Category | RF And Wireless |+| Pins | 33 |++## CAD (KiCad official)++- Symbol: `FSV9520`+- Footprint: `Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm`+- 3D model: QFN-32(5x5) (KiCad packages3D, STEP)+- 3D model files: `fsv9520-etched.step` / `fsv9520-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `fsv9520.step` / `fsv9520.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Forsinve datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8601111649034526720) (74 pp, sha256 `e71ac905eb558462`, retrieved 2026-09-21, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/fsv9520-datasheet.pdf)
page.jsonadded+294@@ -0,0 +1,294 @@+{+ "slug": "fsv9520",+ "version": "0.1.0",+ "type": "component",+ "description": "Forsinve RFID ICs, QFN-32(5x5). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "rf and wireless",+ "fsv9520",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "fsv9520.kicad_sym",+ "fsv9520.kicad_mod",+ "fsv9520.glb",+ "fsv9520.step",+ "fsv9520.lbr",+ "docs/hero.png",+ "docs/fsv9520-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ],+ "component": {+ "mpn": "FSV9520",+ "manufacturer": "Forsinve",+ "package": "QFN-32(5x5)",+ "pin_count": 33,+ "category": "RF And Wireless",+ "subcategory": "RFID ICs",+ "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8601111649034526720",+ "parts": {+ "symbol": "fsv9520.kicad_sym",+ "footprint": "fsv9520.kicad_mod",+ "model_3d": "fsv9520-etched.glb",+ "model_3d_plain": "fsv9520.glb",+ "model_3d_step": "fsv9520-etched.step",+ "model_3d_step_plain": "fsv9520.step",+ "lbr": "fsv9520.lbr"+ },+ "distributor_links": {+ "lcsc": "C5336459"+ },+ "pins": [+ {+ "number": "1",+ "name": "SPI",+ "type": "power_in",+ "description": "Connects to digital ground (DVSS) per pin table description; labeling inconsistency noted"+ },+ {+ "number": "2",+ "name": "PVDD",+ "type": "power_in",+ "description": "Pin power supply voltage, range 1.6V to 3.6V per Table 1 fast reference data"+ },+ {+ "number": "3",+ "name": "DVDD",+ "type": "power_in",+ "description": "Digital power supply voltage, range 2.5V to 3.6V per Table 1 fast reference data"+ },+ {+ "number": "4",+ "name": "DVSS",+ "type": "power_in",+ "description": "Digital ground per pin table; does not require connection to heat sink"+ },+ {+ "number": "5",+ "name": "PVSS",+ "type": "power_in",+ "description": "Pin power ground"+ },+ {+ "number": "6",+ "name": "NRSTPD",+ "type": "input",+ "description": "Reset and power-down input; low level triggers power-down with internal drain current shutdown and oscillator stop, rising edge triggers reset"+ },+ {+ "number": "7",+ "name": "MFIN",+ "type": "input",+ "description": "MIFARE signal input for analog module interface with internal pull-up/pull-down characteristics"+ },+ {+ "number": "8",+ "name": "MFOUT",+ "type": "output",+ "description": "MIFARE signal output from analog module with output current 4mA maximum at 3V"+ },+ {+ "number": "9",+ "name": "SVDD",+ "type": "power_in",+ "description": "Power supply for MFIN and MFOUT pins, range 1.6V to 3.6V per Table 1"+ },+ {+ "number": "10",+ "name": "TVSS",+ "type": "power_in",+ "description": "Transmitter power ground"+ },+ {+ "number": "11",+ "name": "TX1",+ "type": "output",+ "description": "Antenna driver output pin; outputs 13.56MHz modulated energy carrier with maximum IDD(TVDD) up to 100mA"+ },+ {+ "number": "12",+ "name": "TVDD",+ "type": "power_in",+ "description": "Transmitter power supply voltage, range 2.5V to 3.6V per Table 1"+ },+ {+ "number": "13",+ "name": "TX2",+ "type": "output",+ "description": "Antenna driver output pin; outputs 13.56MHz modulated energy carrier for complementary drive configuration"+ },+ {+ "number": "14",+ "name": "TVSS",+ "type": "power_in",+ "description": "Transmitter power ground"+ },+ {+ "number": "15",+ "name": "AVDD",+ "type": "power_in",+ "description": "Analog power supply voltage, range 2.5V to 3.6V per Table 1; must equal VDDA and VDD(TVDD)"+ },+ {+ "number": "16",+ "name": "VMID",+ "type": "power_in",+ "description": "Internal reference voltage for analog circuitry biasing and signal processing"+ },+ {+ "number": "17",+ "name": "RX",+ "type": "input",+ "description": "RF signal input for receiving modulated signals from transponders; input impedance 350Ω, input capacitance 10pF, voltage range ±1V around VDDA with Manchester encoded minimum 5mV at 48dB gain"+ },+ {+ "number": "18",+ "name": "AVSS",+ "type": "power_in",+ "description": "Analog power ground"+ },+ {+ "number": "19",+ "name": "AUX1",+ "type": "output",+ "description": "Auxiliary test output for monitoring internal signals; current source output recommended with 1kΩ pull-down resistor, maximum 4mA"+ },+ {+ "number": "20",+ "name": "AUX2",+ "type": "output",+ "description": "Auxiliary test output for monitoring internal signals; current source output recommended with 1kΩ pull-down resistor, maximum 4mA"+ },+ {+ "number": "21",+ "name": "OSCIN",+ "type": "input",+ "description": "Crystal oscillator buffer input for 27.12MHz crystal or external clock signal; input capacitance 2pF, voltage threshold 0.7VDDA high and 0.3VDDA low"+ },+ {+ "number": "22",+ "name": "OSCOUT",+ "type": "output",+ "description": "Crystal oscillator buffer output; drives 27.12MHz crystal oscillator or provides clock output"+ },+ {+ "number": "23",+ "name": "IRQ",+ "type": "output",+ "description": "Interrupt request output; can be configured as push-pull CMOS output or open-drain output via Diverge register; indicates interrupt events from multiple sources"+ },+ {+ "number": "24",+ "name": "NSS",+ "type": "input",+ "description": "SPI chip select input (active low) for Serial Peripheral Interface control; supports up to 10Mbps SPI data rate"+ },+ {+ "number": "25",+ "name": "D1",+ "type": "bidirectional",+ "description": "Test pin for general purpose test and diagnostic functions; note: function conflicts with footnote [2] references"+ },+ {+ "number": "26",+ "name": "D2",+ "type": "bidirectional",+ "description": "Test pin for general purpose test and diagnostic functions"+ },+ {+ "number": "27",+ "name": "D3",+ "type": "bidirectional",+ "description": "Test pin for general purpose test and diagnostic functions"+ },+ {+ "number": "28",+ "name": "D4",+ "type": "bidirectional",+ "description": "Test pin for general purpose test and diagnostic functions"+ },+ {+ "number": "29",+ "name": "D5",+ "type": "bidirectional",+ "description": "Test pin for diagnostic functions; also functions as SCK (SPI clock input) in SPI mode for serial data synchronization"+ },+ {+ "number": "30",+ "name": "D6",+ "type": "bidirectional",+ "description": "Test pin for diagnostic functions; also functions as MOSI (SPI master output slave input) in SPI mode for host to device data transfer"+ },+ {+ "number": "31",+ "name": "D7",+ "type": "bidirectional",+ "description": "Test pin for diagnostic functions; also functions as MISO (SPI master input slave output) in SPI mode for device to host data transfer"+ },+ {+ "number": "32",+ "name": "EA",+ "type": "power_in",+ "description": "Connects to digital power supply (DVDD) per pin table description; labeling inconsistency noted similar to pin 1"+ },+ {+ "number": "33",+ "name": "EP",+ "type": "passive",+ "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.2",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.2",+ "primary_model": "claude-haiku-4-5-20251001",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-4-6",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: Pin 1 labeled 'SPI' in diagram but table description states 'connects to DVSS' (digital ground); nam; Pin 32 labeled 'EA' in diagram but table description states 'connects to DVDD'; labeling lacks clari; Pins 25-31 (D1-D7) are marked as test pins with I/O type, but pins 29-31 have dual SPI functions; cl",+ "exposed pad 33 added from the footprint"+ ],+ "pages_sent": 74,+ "cost_usd": 0.7396,+ "at": "2026-09-21T22:04:21"+ },+ "datasheet": {+ "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8601111649034526720",+ "pages": 74,+ "sha256": "e71ac905eb558462",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 33,+ "described": 33,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ }+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}