← Commit history

fm24c256e-so-t-g: factory component page (tier=lcsc)

Ray ·3b01988b47 · ·parent 53d40d9
3 files changed +50−24
README.md+32−9
@@ -8,14 +8,14 @@ FM24C256E-SO-T-G from FUDAN MICRO, in a SOP-8. Pinout and pin descriptions extra  | Pin | Name | Type | Function | |---|---|---|---|-| 1 | A0 | input | Device address input bit 0. Hardwired to VCC or GND to set the I2C slave address (allows up to 8 devices on one bus). May be left floating; an internal pull-down to GND is engaged when the VCC-plane capacitive coupling is <3pF. FMSH recommends tying to GND when coupling is >3pF. |-| 2 | A1 | input | Device address input bit 1. Hardwired to VCC or GND to set the I2C slave address. May be left floating; internally pulled down under low-coupling conditions. FMSH recommends tying to GND. |-| 3 | A2 | input | Device address input bit 2. Hardwired to VCC or GND to set the I2C slave address. May be left floating; internally pulled down under low-coupling conditions. FMSH recommends tying to GND. |-| 4 | GND | power_in | Ground reference for the device. |-| 5 | SDA | bidirectional | Bi-directional serial data line for the I2C bus. Open-drain output; requires an external pull-up resistor (1.3 kΩ recommended in AC test conditions) to VCC. May be wire-ORed with other open-drain devices on the bus. |-| 6 | SCL | input | Serial clock input for the I2C bus. Data is clocked into the EEPROM on the positive edge and clocked out on the negative edge. Max 400 kHz at VCC=1.7V, up to 1 MHz at VCC>=2.5V. |-| 7 | WP | input | Write Protect input. Tie to GND for normal write operation; tie to VCC to inhibit all write operations to the memory (full memory protected). May be left floating; internally pulled down under low-coupling conditions. FMSH recommends tying to GND when coupling is >3pF. |-| 8 | VCC | power_in | Positive supply voltage, 1.7V to 5.5V (absolute max 6.25V). Standby current 1.0 µA (1.7V) / 6.0 µA (5.5V); active read/write current up to 3 mA. |+| 1 | A0 | input | Device address input bit 0. Sets one of the three hardware-selectable I2C slave address bits, allowing up to 8 FM24C256E devices on the same 2-wire bus. May be tied high, low, or left floating (internally pulled to GND if V_CC capacitive coupling is <3pF); FMSH recommends tying to GND for reliability. |+| 2 | A1 | input | Device address input bit 1. Hardwired high/low to define the I2C slave address for multi-device bus operation. Left-floating pins are internally pulled to GND under low-coupling conditions; FMSH recommends tying to GND. |+| 3 | A2 | input | Device address input bit 2. Hardwired high/low to define the I2C slave address for multi-device bus operation. Left-floating pins are internally pulled to GND under low-coupling conditions; FMSH recommends tying to GND. |+| 4 | GND | power_in | Ground reference (0V) for the device supply and I/O. |+| 5 | SDA | bidirectional | I2C serial data input/output. Open-drain, wire-OR compatible with other open-drain/open-collector devices. Requires an external pull-up resistor (AC test load 1.3 kΩ to V_CC). Input capacitance ≤6 pF, output capacitance ≤8 pF. |+| 6 | SCL | input | I2C serial clock input. Positive edge clocks data into the EEPROM; negative edge clocks data out. Max 1 MHz at V_CC = 2.5-5.5V, or 400 kHz at V_CC = 1.7V. Schmitt-triggered, noise-filtered input. |+| 7 | WP | input | Write-Protect input. WP = V_CC inhibits all writes to the memory (full memory protected); WP = GND allows normal writes (no protection). Left-floating pins are internally pulled to GND under low-coupling conditions; FMSH recommends tying to GND, then switching to V_CC before a write to create software write-protect. |+| 8 | VCC | power_in | Positive supply voltage. Operating range 1.7V to 5.5V (max 6.25V absolute). Typical supply current 0.4 mA read / 2.0 mA write at 5V/400kHz; standby ≤6.0 µA at 5.5V. |  ## Key specifications @@ -28,7 +28,30 @@ FM24C256E-SO-T-G from FUDAN MICRO, in a SOP-8. Pinout and pin descriptions extra  ## Ordering variants -- `FM24C256E-SO-T-GSO`+- `FM24C256E-SO-T-GSO-U`+- `FM24C256E-SO-T-GSO-T`+- `FM24C256E-SO-T-GSO-U-R`+- `FM24C256E-SO-T-GSO-T-R`+- `FM24C256E-SO-T-GSO-U-G`+- `FM24C256E-SO-T-GSO-T-G`+- `FM24C256E-SO-T-GTS-U`+- `FM24C256E-SO-T-GTS-T`+- `FM24C256E-SO-T-GTS-U-R`+- `FM24C256E-SO-T-GTS-T-R`+- `FM24C256E-SO-T-GTS-U-G`+- `FM24C256E-SO-T-GTS-T-G`+- `FM24C256E-SO-T-GMS-U`+- `FM24C256E-SO-T-GMS-T`+- `FM24C256E-SO-T-GMS-U-G`+- `FM24C256E-SO-T-GMS-T-G`+- `FM24C256E-SO-T-GDN-U-G`+- `FM24C256E-SO-T-GDN-T-G`+- `FM24C256E-SO-T-GM2F-R`+- `FM24C256E-SO-T-GM2P-R`+- `FM24C256E-SO-T-GCT-R`+- `FM24C256E-SO-T-GCT-T`+- `FM24C256E-SO-T-GCTB-R`+- `FM24C256E-SO-T-GCTB-T`  ## CAD (KiCad official) 
fm24c256e-so-t-g.lbr+9−3
@@ -50,7 +50,7 @@ <layer number="98" name="Guide" color="6" fill="1" visible="yes" active="yes"/> </layers> <library>-<description></description>+<description>FUDAN MICRO EEPROM, SOP-8</description> <packages> <package name="SOIC-8_3.9x4.9mm_P1.27mm">   <description>SOIC-8, 3.9 x 4.9 mm, 1.27 mm pitch</description>@@ -86,6 +86,7 @@ </packages> <symbols> <symbol name="FM24C256E-SO-T-G">+  <description>FUDAN MICRO EEPROM, SOP-8</description>   <wire x1="-12.7" y1="5.08" x2="12.7" y2="5.08" width="0.254" layer="94"/>   <wire x1="12.7" y1="5.08" x2="12.7" y2="-7.62" width="0.254" layer="94"/>   <wire x1="12.7" y1="-7.62" x2="-12.7" y2="-7.62" width="0.254" layer="94"/>@@ -104,7 +105,7 @@ </symbols> <devicesets> <deviceset name="FM24C256E-SO-T-G" prefix="U">-  <description></description>+  <description>FUDAN MICRO EEPROM, SOP-8</description>   <gates>     <gate name="G$1" symbol="FM24C256E-SO-T-G" x="0" y="0"/>   </gates>@@ -120,7 +121,12 @@         <connect gate="G$1" pin="SCL" pad="6"/>         <connect gate="G$1" pin="SDA" pad="5"/>       </connects>-      <technologies><technology name=""/></technologies>+      <technologies>+        <technology name="">+          <attribute name="MPN" value="FM24C256E-SO-T-G" constant="no"/>+          <attribute name="MANUFACTURER" value="FUDAN MICRO" constant="no"/>+        </technology>+      </technologies>     </device>   </devices> </deviceset>
page.json+9−12
@@ -32,49 +32,49 @@         "number": "1",         "name": "A0",         "type": "input",-        "description": "Device address input bit 0. Hardwired to VCC or GND to set the I2C slave address (allows up to 8 devices on one bus). May be left floating; an internal pull-down to GND is engaged when the VCC-plane capacitive coupling is <3pF. FMSH recommends tying to GND when coupling is >3pF."+        "description": "Device address input bit 0. Sets one of the three hardware-selectable I2C slave address bits, allowing up to 8 FM24C256E devices on the same 2-wire bus. May be tied high, low, or left floating (internally pulled to GND if V_CC capacitive coupling is <3pF); FMSH recommends tying to GND for reliability."       },       {         "number": "2",         "name": "A1",         "type": "input",-        "description": "Device address input bit 1. Hardwired to VCC or GND to set the I2C slave address. May be left floating; internally pulled down under low-coupling conditions. FMSH recommends tying to GND."+        "description": "Device address input bit 1. Hardwired high/low to define the I2C slave address for multi-device bus operation. Left-floating pins are internally pulled to GND under low-coupling conditions; FMSH recommends tying to GND."       },       {         "number": "3",         "name": "A2",         "type": "input",-        "description": "Device address input bit 2. Hardwired to VCC or GND to set the I2C slave address. May be left floating; internally pulled down under low-coupling conditions. FMSH recommends tying to GND."+        "description": "Device address input bit 2. Hardwired high/low to define the I2C slave address for multi-device bus operation. Left-floating pins are internally pulled to GND under low-coupling conditions; FMSH recommends tying to GND."       },       {         "number": "4",         "name": "GND",         "type": "power_in",-        "description": "Ground reference for the device."+        "description": "Ground reference (0V) for the device supply and I/O."       },       {         "number": "5",         "name": "SDA",         "type": "bidirectional",-        "description": "Bi-directional serial data line for the I2C bus. Open-drain output; requires an external pull-up resistor (1.3 kΩ recommended in AC test conditions) to VCC. May be wire-ORed with other open-drain devices on the bus."+        "description": "I2C serial data input/output. Open-drain, wire-OR compatible with other open-drain/open-collector devices. Requires an external pull-up resistor (AC test load 1.3 k\u03a9 to V_CC). Input capacitance \u22646 pF, output capacitance \u22648 pF."       },       {         "number": "6",         "name": "SCL",         "type": "input",-        "description": "Serial clock input for the I2C bus. Data is clocked into the EEPROM on the positive edge and clocked out on the negative edge. Max 400 kHz at VCC=1.7V, up to 1 MHz at VCC>=2.5V."+        "description": "I2C serial clock input. Positive edge clocks data into the EEPROM; negative edge clocks data out. Max 1 MHz at V_CC = 2.5-5.5V, or 400 kHz at V_CC = 1.7V. Schmitt-triggered, noise-filtered input."       },       {         "number": "7",         "name": "WP",         "type": "input",-        "description": "Write Protect input. Tie to GND for normal write operation; tie to VCC to inhibit all write operations to the memory (full memory protected). May be left floating; internally pulled down under low-coupling conditions. FMSH recommends tying to GND when coupling is >3pF."+        "description": "Write-Protect input. WP = V_CC inhibits all writes to the memory (full memory protected); WP = GND allows normal writes (no protection). Left-floating pins are internally pulled to GND under low-coupling conditions; FMSH recommends tying to GND, then switching to V_CC before a write to create software write-protect."       },       {         "number": "8",         "name": "VCC",         "type": "power_in",-        "description": "Positive supply voltage, 1.7V to 5.5V (absolute max 6.25V). Standby current 1.0 µA (1.7V) / 6.0 µA (5.5V); active read/write current up to 3 mA."+        "description": "Positive supply voltage. Operating range 1.7V to 5.5V (max 6.25V absolute). Typical supply current 0.4 mA read / 2.0 mA write at 5V/400kHz; standby \u22646.0 \u00b5A at 5.5V."       }     ],     "provenance": {@@ -138,8 +138,5 @@     "docs/fm24c256e-so-t-g-datasheet.pdf",     "viewers/symbol.html",     "viewers/footprint.html"-  ],-  "visibility": {-    "public": true-  }+  ] }\ No newline at end of file