component
FM1906
Public Made by Adomby adom
Shenzhen Fuman LCD Drivers, SSOP-24-150mil. Pinout extracted from the datasheet, KiCad symbol/footprint/3D.
← Commit history
fm1906: factory component page (tier=lcsc)
3 files changed
+48−45
README.md+19−19@@ -8,30 +8,30 @@ FM1906 from Shenzhen Fuman, in a SSOP-24-150mil. Pinout and pin descriptions ext | Pin | Name | Type | Function | |---|---|---|---|-| 1 | SEG4 | output | LCD segment output 4 (drives an LCD segment electrode with the 1/2 or 1/3 bias LCD waveform). |-| 2 | SEG2 | output | LCD segment output 2. |-| 3 | CSB | input | Chip-select input, active-low. Requires external pull-up. High disables read/write and resets the serial interface; low enables serial data/command transactions. |-| 4 | RDB | input | READ strobe input, active-low. Requires external pull-up. On the falling edge of RDB the internal RAM data is driven onto DATA; the host can latch it on the next rising edge. |-| 5 | WRB | input | WRITE strobe input, active-low. Requires external pull-up. On the rising edge of WRB the data on the DATA line is latched into FM1906. |-| 6 | DATA | bidirectional | Bidirectional serial data line for the 4-wire interface. Requires external pull-up resistor. Also serves as tone/IRQ output when configured by software. |+| 1 | SEG4 | output | LCD segment output SEG4. |+| 2 | SEG2 | output | LCD segment output SEG2. |+| 3 | CSB | input | Active-low chip select input with internal pull-up. When CSB is high the serial interface is reset and read/write to FM1906 is disabled; when low, serial commands and data are accepted. |+| 4 | RDB | input | Active-low READ strobe input with internal pull-up. On the falling edge of RDB, RAM data is driven onto DATA and latched by the host on the next rising edge. |+| 5 | WRB | input | Active-low WRITE strobe input with internal pull-up. On the rising edge of WRB, the data present on DATA is written into FM1906. |+| 6 | DATA | bidirectional | Serial data input/output for the 4-wire host interface; requires an external pull-up resistor. Direction is controlled by WRB/RDB. | | 7 | VSS | power_in | Negative supply / ground reference (0 V). |-| 8 | VLCD | power_in | LCD bias supply input. Must satisfy VLCD < VDD; used to set the LCD contrast/operating voltage (e.g. VLCD=4 V with VDD=5 V via a 15 kΩ trimmer). |-| 9 | VDD | power_in | Positive supply, 3.0-5.0 V (abs max 5.5 V). |+| 8 | VLCD | power_in | LCD bias supply input used by the internal LCD bias circuit; VLCD must be less than VDD and is typically set via an external adjustable resistor to tune LCD contrast (e.g. VDD=5V, VLCD=4V with R=15kΩ ±20%). |+| 9 | VDD | power_in | Positive supply pin, 3.0-5.0 V operating range (absolute max 5.5 V). | | 10 | COM0 | output | LCD common (backplane) output 0. | | 11 | COM1 | output | LCD common (backplane) output 1. | | 12 | COM2 | output | LCD common (backplane) output 2. | | 13 | COM3 | output | LCD common (backplane) output 3. |-| 14 | SEG26 | output | LCD segment output 26. |-| 15 | SEG24 | output | LCD segment output 24. |-| 16 | SEG22 | output | LCD segment output 22. |-| 17 | SEG20 | output | LCD segment output 20. |-| 18 | SEG18 | output | LCD segment output 18. |-| 19 | SEG16 | output | LCD segment output 16. |-| 20 | SEG14 | output | LCD segment output 14. |-| 21 | SEG12 | output | LCD segment output 12. |-| 22 | SEG10 | output | LCD segment output 10. |-| 23 | SEG8 | output | LCD segment output 8. |-| 24 | SEG6 | output | LCD segment output 6. |+| 14 | SEG26 | output | LCD segment output SEG26. |+| 15 | SEG24 | output | LCD segment output SEG24. |+| 16 | SEG22 | output | LCD segment output SEG22. |+| 17 | SEG20 | output | LCD segment output SEG20. |+| 18 | SEG18 | output | LCD segment output SEG18. |+| 19 | SEG16 | output | LCD segment output SEG16. |+| 20 | SEG14 | output | LCD segment output SEG14. |+| 21 | SEG12 | output | LCD segment output SEG12. |+| 22 | SEG10 | output | LCD segment output SEG10. |+| 23 | SEG8 | output | LCD segment output SEG8. |+| 24 | SEG6 | output | LCD segment output SEG6. | ## Key specifications
fm1906.lbr+9−3@@ -50,7 +50,7 @@ <layer number="98" name="Guide" color="6" fill="1" visible="yes" active="yes"/> </layers> <library>-<description></description>+<description>Shenzhen Fuman LCD Drivers, SSOP-24-150mil</description> <packages> <package name="SSOP-24_5.3x8.2mm_P0.65mm"> <description>SSOP-24, 5.3 x 8.2 mm, 0.65 mm pitch</description>@@ -102,6 +102,7 @@ </packages> <symbols> <symbol name="FM1906">+ <description>Shenzhen Fuman LCD Drivers, SSOP-24-150mil</description> <wire x1="-12.7" y1="15.24" x2="12.7" y2="15.24" width="0.254" layer="94"/> <wire x1="12.7" y1="15.24" x2="12.7" y2="-17.78" width="0.254" layer="94"/> <wire x1="12.7" y1="-17.78" x2="-12.7" y2="-17.78" width="0.254" layer="94"/>@@ -136,7 +137,7 @@ </symbols> <devicesets> <deviceset name="FM1906" prefix="U">- <description></description>+ <description>Shenzhen Fuman LCD Drivers, SSOP-24-150mil</description> <gates> <gate name="G$1" symbol="FM1906" x="0" y="0"/> </gates>@@ -168,7 +169,12 @@ <connect gate="G$1" pin="SEG26" pad="14"/> <connect gate="G$1" pin="COM3" pad="13"/> </connects>- <technologies><technology name=""/></technologies>+ <technologies>+ <technology name="">+ <attribute name="MPN" value="FM1906" constant="no"/>+ <attribute name="MANUFACTURER" value="Shenzhen Fuman" constant="no"/>+ </technology>+ </technologies> </device> </devices> </deviceset>
page.json+20−23@@ -32,37 +32,37 @@ "number": "1", "name": "SEG4", "type": "output",- "description": "LCD segment output 4 (drives an LCD segment electrode with the 1/2 or 1/3 bias LCD waveform)."+ "description": "LCD segment output SEG4." }, { "number": "2", "name": "SEG2", "type": "output",- "description": "LCD segment output 2."+ "description": "LCD segment output SEG2." }, { "number": "3", "name": "CSB", "type": "input",- "description": "Chip-select input, active-low. Requires external pull-up. High disables read/write and resets the serial interface; low enables serial data/command transactions."+ "description": "Active-low chip select input with internal pull-up. When CSB is high the serial interface is reset and read/write to FM1906 is disabled; when low, serial commands and data are accepted." }, { "number": "4", "name": "RDB", "type": "input",- "description": "READ strobe input, active-low. Requires external pull-up. On the falling edge of RDB the internal RAM data is driven onto DATA; the host can latch it on the next rising edge."+ "description": "Active-low READ strobe input with internal pull-up. On the falling edge of RDB, RAM data is driven onto DATA and latched by the host on the next rising edge." }, { "number": "5", "name": "WRB", "type": "input",- "description": "WRITE strobe input, active-low. Requires external pull-up. On the rising edge of WRB the data on the DATA line is latched into FM1906."+ "description": "Active-low WRITE strobe input with internal pull-up. On the rising edge of WRB, the data present on DATA is written into FM1906." }, { "number": "6", "name": "DATA", "type": "bidirectional",- "description": "Bidirectional serial data line for the 4-wire interface. Requires external pull-up resistor. Also serves as tone/IRQ output when configured by software."+ "description": "Serial data input/output for the 4-wire host interface; requires an external pull-up resistor. Direction is controlled by WRB/RDB." }, { "number": "7",@@ -74,13 +74,13 @@ "number": "8", "name": "VLCD", "type": "power_in",- "description": "LCD bias supply input. Must satisfy VLCD < VDD; used to set the LCD contrast/operating voltage (e.g. VLCD=4 V with VDD=5 V via a 15 kΩ trimmer)."+ "description": "LCD bias supply input used by the internal LCD bias circuit; VLCD must be less than VDD and is typically set via an external adjustable resistor to tune LCD contrast (e.g. VDD=5V, VLCD=4V with R=15k\u03a9 \u00b120%)." }, { "number": "9", "name": "VDD", "type": "power_in",- "description": "Positive supply, 3.0-5.0 V (abs max 5.5 V)."+ "description": "Positive supply pin, 3.0-5.0 V operating range (absolute max 5.5 V)." }, { "number": "10",@@ -110,67 +110,67 @@ "number": "14", "name": "SEG26", "type": "output",- "description": "LCD segment output 26."+ "description": "LCD segment output SEG26." }, { "number": "15", "name": "SEG24", "type": "output",- "description": "LCD segment output 24."+ "description": "LCD segment output SEG24." }, { "number": "16", "name": "SEG22", "type": "output",- "description": "LCD segment output 22."+ "description": "LCD segment output SEG22." }, { "number": "17", "name": "SEG20", "type": "output",- "description": "LCD segment output 20."+ "description": "LCD segment output SEG20." }, { "number": "18", "name": "SEG18", "type": "output",- "description": "LCD segment output 18."+ "description": "LCD segment output SEG18." }, { "number": "19", "name": "SEG16", "type": "output",- "description": "LCD segment output 16."+ "description": "LCD segment output SEG16." }, { "number": "20", "name": "SEG14", "type": "output",- "description": "LCD segment output 14."+ "description": "LCD segment output SEG14." }, { "number": "21", "name": "SEG12", "type": "output",- "description": "LCD segment output 12."+ "description": "LCD segment output SEG12." }, { "number": "22", "name": "SEG10", "type": "output",- "description": "LCD segment output 10."+ "description": "LCD segment output SEG10." }, { "number": "23", "name": "SEG8", "type": "output",- "description": "LCD segment output 8."+ "description": "LCD segment output SEG8." }, { "number": "24", "name": "SEG6", "type": "output",- "description": "LCD segment output 6."+ "description": "LCD segment output SEG6." } ], "provenance": {@@ -234,8 +234,5 @@ "docs/fm1906-datasheet.pdf", "viewers/symbol.html", "viewers/footprint.html"- ],- "visibility": {- "public": true- }+ ] }