← Commit history

eg8305: factory component page (tier=lcsc)

Ray ·6855b7fb6d · ·parent d2dee09
4 files changed +29−26
README.md+8−8
@@ -8,14 +8,14 @@ EG8305 from EG Micro, in a SOP-8. Pinout and pin descriptions extracted from the  | Pin | Name | Type | Function | |---|---|---|---|-| 1 | CTRL | input | Enable/shutdown control input. Drive high (VIH min 1V @ VDD=5V) to enable the amplifier; drive low (VIL max 0.7V) to shut down (ISD < 1uA). |-| 2 | BYPASS | passive | Internal reference bypass capacitor input. Connect a 1uF capacitor to GND to filter the internal bias/Vref voltage (nominally VDD/2). |-| 3 | INP | input | Differential audio input, positive terminal. AC-couple via input capacitor (typ 0.1uF) with series input resistor (typ 30k); combined with internal 20k Ri and 180k Rf feedback yields a max closed-loop gain of 25dB. |-| 4 | INN | input | Differential audio input, negative terminal. AC-couple via input capacitor (typ 0.1uF) with series input resistor (typ 30k) to signal ground. |-| 5 | VON | output | Bridge-tied-load (BTL) Class-D output, negative side. Drives one terminal of the loudspeaker (typ 4Ω or 8Ω); RDS(on) ~465mΩ (high-side PMOS + low-side NMOS) @ VDD=5V, I=500mA; switching frequency 250kHz. |-| 6 | VDD | power_in | Supply voltage input, 3.0V to 5.5V (absolute max 6.0V). Decouple with a 1uF ceramic close to the pin, plus a 10uF or larger bulk capacitor nearby. |-| 7 | GND | power_in | Device ground. Common return for supply, bypass capacitor, and EMI filter capacitors on the output. |-| 8 | VOP | output | Bridge-tied-load (BTL) Class-D output, positive side. Drives the other terminal of the loudspeaker; delivers up to 3W into 4Ω @ VDD=5V, THD+N=10%. |+| 1 | CTRL | input | Chip enable / shutdown control input. Pulling this pin high (typ. VIH ≥ 1 V at VDD=5.0 V) enables the amplifier; low (VIL ≤ 0.7 V) puts the device into shutdown (ISD < 1 µA). |+| 2 | BYPASS | input | Internal reference / bias bypass capacitor node. Connect a 1 µF ceramic capacitor from this pin to GND to filter the internal mid-rail reference for low-noise operation. |+| 3 | INP | input | Differential audio input, positive side. AC-couple the audio source through Ci (typ. 0.1 µF) to this pin; internal input resistor Ri ≈ 20 kΩ, external Re typically 30 kΩ to set closed-loop gain up to 25 dB. |+| 4 | INN | input | Differential audio input, negative side. AC-couple through Ci (typ. 0.1 µF); usually tied to signal ground through the same 30 kΩ / 0.1 µF network as INP for single-ended sources. |+| 5 | VON | output | Class-D bridge-tied-load (BTL) output, negative side. Drives one terminal of the speaker (4 Ω or 8 Ω). Half of the H-bridge with high-side PMOS / low-side NMOS RDS(on) ≈ 465 mΩ at VDD=5 V. |+| 6 | VDD | power_in | Supply voltage input, 3.0 V to 5.5 V (absolute max 6.0 V). Decouple with a 1 µF ceramic close to the pin and an additional 10 µF bulk capacitor for low-frequency noise rejection. |+| 7 | GND | power_in | Device ground. Return for supply decoupling and speaker filter capacitors; connect to the board power ground plane. |+| 8 | VOP | output | Class-D bridge-tied-load (BTL) output, positive side. Drives the other terminal of the speaker; complements VON to deliver up to 3 W into 4 Ω at 5 V. |  ## Key specifications 
eg8305.kicad_sym+1−1
@@ -12,7 +12,7 @@       (name "CTRL" (effects (font (size 1.27 1.27))))       (number "1" (effects (font (size 1.27 1.27))))     )-    (pin passive line (at -17.78 0.00 0) (length 5.08)+    (pin input line (at -17.78 0.00 0) (length 5.08)       (name "BYPASS" (effects (font (size 1.27 1.27))))       (number "2" (effects (font (size 1.27 1.27))))     )
eg8305.lbr+10−4
@@ -50,7 +50,7 @@ <layer number="98" name="Guide" color="6" fill="1" visible="yes" active="yes"/> </layers> <library>-<description></description>+<description>EG Micro Audio Power OpAmps, SOP-8</description> <packages> <package name="SOIC-8_3.9x4.9mm_P1.27mm">   <description>SOIC-8, 3.9 x 4.9 mm, 1.27 mm pitch</description>@@ -86,6 +86,7 @@ </packages> <symbols> <symbol name="EG8305">+  <description>EG Micro Audio Power OpAmps, SOP-8</description>   <wire x1="-12.7" y1="5.08" x2="12.7" y2="5.08" width="0.254" layer="94"/>   <wire x1="12.7" y1="5.08" x2="12.7" y2="-7.62" width="0.254" layer="94"/>   <wire x1="12.7" y1="-7.62" x2="-12.7" y2="-7.62" width="0.254" layer="94"/>@@ -93,7 +94,7 @@   <text x="0.0000" y="7.6200" size="1.27" layer="95" align="center">&gt;NAME</text>   <text x="0.0000" y="-10.1600" size="1.27" layer="96" align="center">&gt;VALUE</text>   <pin name="CTRL" x="-17.78" y="2.54" length="middle" direction="in"/>-  <pin name="BYPASS" x="-17.78" y="0" length="middle" direction="pas"/>+  <pin name="BYPASS" x="-17.78" y="0" length="middle" direction="in"/>   <pin name="INP" x="-17.78" y="-2.54" length="middle" direction="in"/>   <pin name="INN" x="-17.78" y="-5.08" length="middle" direction="in"/>   <pin name="VOP" x="17.78" y="2.54" length="middle" direction="out" rot="R180"/>@@ -104,7 +105,7 @@ </symbols> <devicesets> <deviceset name="EG8305" prefix="U">-  <description></description>+  <description>EG Micro Audio Power OpAmps, SOP-8</description>   <gates>     <gate name="G$1" symbol="EG8305" x="0" y="0"/>   </gates>@@ -120,7 +121,12 @@         <connect gate="G$1" pin="VDD" pad="6"/>         <connect gate="G$1" pin="VON" pad="5"/>       </connects>-      <technologies><technology name=""/></technologies>+      <technologies>+        <technology name="">+          <attribute name="MPN" value="EG8305" constant="no"/>+          <attribute name="MANUFACTURER" value="EG Micro" constant="no"/>+        </technology>+      </technologies>     </device>   </devices> </deviceset>
page.json+10−13
@@ -32,49 +32,49 @@         "number": "1",         "name": "CTRL",         "type": "input",-        "description": "Enable/shutdown control input. Drive high (VIH min 1V @ VDD=5V) to enable the amplifier; drive low (VIL max 0.7V) to shut down (ISD < 1uA)."+        "description": "Chip enable / shutdown control input. Pulling this pin high (typ. VIH \u2265 1 V at VDD=5.0 V) enables the amplifier; low (VIL \u2264 0.7 V) puts the device into shutdown (ISD < 1 \u00b5A)."       },       {         "number": "2",         "name": "BYPASS",-        "type": "passive",-        "description": "Internal reference bypass capacitor input. Connect a 1uF capacitor to GND to filter the internal bias/Vref voltage (nominally VDD/2)."+        "type": "input",+        "description": "Internal reference / bias bypass capacitor node. Connect a 1 \u00b5F ceramic capacitor from this pin to GND to filter the internal mid-rail reference for low-noise operation."       },       {         "number": "3",         "name": "INP",         "type": "input",-        "description": "Differential audio input, positive terminal. AC-couple via input capacitor (typ 0.1uF) with series input resistor (typ 30k); combined with internal 20k Ri and 180k Rf feedback yields a max closed-loop gain of 25dB."+        "description": "Differential audio input, positive side. AC-couple the audio source through Ci (typ. 0.1 \u00b5F) to this pin; internal input resistor Ri \u2248 20 k\u03a9, external Re typically 30 k\u03a9 to set closed-loop gain up to 25 dB."       },       {         "number": "4",         "name": "INN",         "type": "input",-        "description": "Differential audio input, negative terminal. AC-couple via input capacitor (typ 0.1uF) with series input resistor (typ 30k) to signal ground."+        "description": "Differential audio input, negative side. AC-couple through Ci (typ. 0.1 \u00b5F); usually tied to signal ground through the same 30 k\u03a9 / 0.1 \u00b5F network as INP for single-ended sources."       },       {         "number": "5",         "name": "VON",         "type": "output",-        "description": "Bridge-tied-load (BTL) Class-D output, negative side. Drives one terminal of the loudspeaker (typ 4Ω or 8Ω); RDS(on) ~465mΩ (high-side PMOS + low-side NMOS) @ VDD=5V, I=500mA; switching frequency 250kHz."+        "description": "Class-D bridge-tied-load (BTL) output, negative side. Drives one terminal of the speaker (4 \u03a9 or 8 \u03a9). Half of the H-bridge with high-side PMOS / low-side NMOS RDS(on) \u2248 465 m\u03a9 at VDD=5 V."       },       {         "number": "6",         "name": "VDD",         "type": "power_in",-        "description": "Supply voltage input, 3.0V to 5.5V (absolute max 6.0V). Decouple with a 1uF ceramic close to the pin, plus a 10uF or larger bulk capacitor nearby."+        "description": "Supply voltage input, 3.0 V to 5.5 V (absolute max 6.0 V). Decouple with a 1 \u00b5F ceramic close to the pin and an additional 10 \u00b5F bulk capacitor for low-frequency noise rejection."       },       {         "number": "7",         "name": "GND",         "type": "power_in",-        "description": "Device ground. Common return for supply, bypass capacitor, and EMI filter capacitors on the output."+        "description": "Device ground. Return for supply decoupling and speaker filter capacitors; connect to the board power ground plane."       },       {         "number": "8",         "name": "VOP",         "type": "output",-        "description": "Bridge-tied-load (BTL) Class-D output, positive side. Drives the other terminal of the loudspeaker; delivers up to 3W into 4Ω @ VDD=5V, THD+N=10%."+        "description": "Class-D bridge-tied-load (BTL) output, positive side. Drives the other terminal of the speaker; complements VON to deliver up to 3 W into 4 \u03a9 at 5 V."       }     ],     "provenance": {@@ -138,8 +138,5 @@     "docs/eg8305-datasheet.pdf",     "viewers/symbol.html",     "viewers/footprint.html"-  ],-  "visibility": {-    "public": true-  }+  ] }\ No newline at end of file