DRV8860PWR

@@ -53,25 +53,25 @@         "number": "1",         "name": "VM",         "type": "power_in",-        "description": "Motor power supply plus pin; supply voltage range 8 to 38 V, bypass to GND with 0.1 \u03bcF ceramic and 10 \u03bcF electrolytic capacitors."+        "description": "Motor power supply plus pin; supply voltage range 8 to 38 V, bypass to GND with 0.1 μF ceramic and 10 μF electrolytic capacitors."       },       {         "number": "2",         "name": "DIN",         "type": "input",-        "description": "Serial data input from controller with internal pulldown resistance of 100 k\u03a9."+        "description": "Serial data input from controller with internal pulldown resistance of 100 kΩ."       },       {         "number": "3",         "name": "CLK",         "type": "input",-        "description": "Serial clock input; rising edge clocks data into device for write operations, falling edge clocks data out for read operations; internal pulldown resistance of 100 k\u03a9."+        "description": "Serial clock input; rising edge clocks data into device for write operations, falling edge clocks data out for read operations; internal pulldown resistance of 100 kΩ."       },       {         "number": "4",         "name": "LATCH",         "type": "input",-        "description": "Serial latch signal for latching data into output register; internal pulldown resistance of 100 k\u03a9."+        "description": "Serial latch signal for latching data into output register; internal pulldown resistance of 100 kΩ."       },       {         "number": "5",@@ -83,19 +83,19 @@         "number": "6",         "name": "DOUT",         "type": "output",-        "description": "Serial data output to controller; open-drain output with internal pullup resistance of 1.4 k\u03a9 to internal 5.7 V."+        "description": "Serial data output to controller; open-drain output with internal pullup resistance of 1.4 kΩ to internal 5.7 V."       },       {         "number": "7",         "name": "nFAULT",         "type": "tri_state",-        "description": "Fault output driven logic low when in fault condition (OCP, OTS, UVLO, OL); open-drain output requiring external pullup to V3P3, typical pullup resistor greater than 4.7 k\u03a9."+        "description": "Fault output driven logic low when in fault condition (OCP, OTS, UVLO, OL); open-drain output requiring external pullup to V3P3, typical pullup resistor greater than 4.7 kΩ."       },       {         "number": "8",         "name": "ENABLE",         "type": "input",-        "description": "Logic high enables output drivers, logic low disables outputs and allows internal logic and control register read/write operations; internal pulldown resistance of 100 k\u03a9."+        "description": "Logic high enables output drivers, logic low disables outputs and allows internal logic and control register read/write operations; internal pulldown resistance of 100 kΩ."       },       {         "number": "9",@@ -178,6 +178,46 @@     "viewers": {       "symbol": "viewers/symbol.html",       "footprint": "viewers/footprint.html"-    }+    },+    "models_3d": [+      {+        "file": "drv8860pwr.step",+        "role": "plain",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          6.4,+          5.0,+          1.1+        ],+        "zmin_mm": -0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "6ad5e98224d02a427d9a6b929a28dbc158b9925fba5adec12db05079f1016948",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      },+      {+        "file": "drv8860pwr-etched.step",+        "role": "eda",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          6.4,+          5.0,+          1.1+        ],+        "zmin_mm": -0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "b0fef3c1544e38c49c77f079d207cd026525596fde006a517a7af465650efb6c",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      }+    ]   }-}\ No newline at end of file+}