component
DRV8806PWPR
Public Made by Adomby adom
Texas Instruments Stepper Motor Driver, HTSSOP-16-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+54@@ -0,0 +1,54 @@+# DRV8806PWPR++**Texas Instruments** · Stepper Motor Driver · HTSSOP-16-EP++DRV8806PWPR from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VM | power_in | Device power supply, connect to the motor supply; the datasheet specifies 8.2 V to 40 V. |+| 2 | VCLAMP | passive | Output clamp voltage, connected to the VM supply or to a zener/TVS diode to VM to clamp inductive turn-off transients; recommended range 0 to 40 V and it is not a power supply input. |+| 3 | OUT1 | output | Low-side driver output 1 connected to load 1; outputs must not exceed the 43 V absolute maximum output voltage. |+| 4 | OUT2 | output | Low-side driver output 2 connected to load 2; outputs must not exceed the 43 V absolute maximum output voltage. |+| 5 | GND | power_in | Device ground; all GND pins must be connected to ground. |+| 6 | OUT3 | output | Low-side driver output 3 connected to load 3; outputs must not exceed the 43 V absolute maximum output voltage. |+| 7 | OUT4 | output | Low-side driver output 4 connected to load 4; outputs must not exceed the 43 V absolute maximum output voltage. |+| 8 | nENBL | input | Active-low enable input (internal pulldown); outputs are enabled when driven low and disabled when driven high, with digital input limits of -0.5 V to 7 V. |+| 9 | RESET | input | Active-high reset input (internal pulldown) that initializes internal logic, clears the overcurrent fault and serial interface registers; digital input limits of -0.5 V to 7 V. |+| 10 | NC | unconnected | No connection shown in the pin configuration diagram; not listed in the Pin Functions table. |+| 11 | LATCH | input | Latch input (internal pulldown); a rising edge latches the shift register to the outputs and a falling edge latches fault data, with a minimum pulse width of 200 ns. |+| 12 | GND | power_in | Device ground; all GND pins must be connected to ground. |+| 13 | SCLK | input | Serial clock input (internal pulldown); data is shifted in on each rising edge with a minimum clock cycle time of 62 ns. |+| 14 | SDATIN | input | Serial data input (internal pulldown) sampled on the SCLK rising edge with 5 ns minimum setup time to SCLK. |+| 15 | SDATOUT | output | Serial data output with push-pull structure and internal pullup, able to drive another DRV8806 SDATIN up to 1 MHz without external pullup; sources about 1 mA and sinks about 5 mA. |+| 16 | nFAULT | output | Open-drain fault output driven low on overtemperature, overcurrent or open load, with output low voltage of 0.5 V max at 5 mA. |+| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | HTSSOP-16-EP |+| Category | Motor Driver ICs |+| Pins | 17 |++## CAD (KiCad official)++- Symbol: `DRV8806PWPR`+- Footprint: `Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm`+- 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)+- 3D model files: `drv8806pwpr-etched.step` / `drv8806pwpr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `drv8806pwpr.step` / `drv8806pwpr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/drv8806) (26 pp, sha256 `ae0b5f785bd9778e`, retrieved 2026-10-08, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/drv8806pwpr-datasheet.pdf)
page.jsonadded+255@@ -0,0 +1,255 @@+{+ "slug": "drv8806pwpr",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments Stepper Motor Driver, HTSSOP-16-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "motor driver ics",+ "drv8806pwpr",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "drv8806pwpr.kicad_sym",+ "drv8806pwpr.kicad_mod",+ "drv8806pwpr.glb",+ "drv8806pwpr.step",+ "drv8806pwpr.lbr",+ "docs/hero.png",+ "docs/drv8806pwpr-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "drv8806pwpr-hero.glb",+ "drv8806pwpr-hero.overlay.json"+ ],+ "component": {+ "mpn": "DRV8806PWPR",+ "manufacturer": "Texas Instruments",+ "package": "HTSSOP-16-EP",+ "pin_count": 17,+ "category": "Motor Driver ICs",+ "subcategory": "Stepper Motor Driver",+ "datasheet": "https://www.ti.com/cn/lit/gpn/drv8806",+ "parts": {+ "symbol": "drv8806pwpr.kicad_sym",+ "footprint": "drv8806pwpr.kicad_mod",+ "model_3d": "drv8806pwpr-hero.glb",+ "model_3d_plain": "drv8806pwpr.glb",+ "model_3d_step": "drv8806pwpr-etched.step",+ "model_3d_step_plain": "drv8806pwpr.step",+ "lbr": "drv8806pwpr.lbr"+ },+ "distributor_links": {+ "lcsc": "C701794",+ "digikey": "296-34887-2-ND",+ "mouser": "595-DRV8806PWPR"+ },+ "distributor_check": {+ "checked_at": "2026-10-08T02:50:47Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "296-34887-2-ND",+ "status": "found",+ "lifecycle": "Active"+ },+ "mouser": {+ "pn": "595-DRV8806PWPR",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "VM",+ "type": "power_in",+ "description": "Device power supply, connect to the motor supply; the datasheet specifies 8.2 V to 40 V."+ },+ {+ "number": "2",+ "name": "VCLAMP",+ "type": "passive",+ "description": "Output clamp voltage, connected to the VM supply or to a zener/TVS diode to VM to clamp inductive turn-off transients; recommended range 0 to 40 V and it is not a power supply input."+ },+ {+ "number": "3",+ "name": "OUT1",+ "type": "output",+ "description": "Low-side driver output 1 connected to load 1; outputs must not exceed the 43 V absolute maximum output voltage."+ },+ {+ "number": "4",+ "name": "OUT2",+ "type": "output",+ "description": "Low-side driver output 2 connected to load 2; outputs must not exceed the 43 V absolute maximum output voltage."+ },+ {+ "number": "5",+ "name": "GND",+ "type": "power_in",+ "description": "Device ground; all GND pins must be connected to ground."+ },+ {+ "number": "6",+ "name": "OUT3",+ "type": "output",+ "description": "Low-side driver output 3 connected to load 3; outputs must not exceed the 43 V absolute maximum output voltage."+ },+ {+ "number": "7",+ "name": "OUT4",+ "type": "output",+ "description": "Low-side driver output 4 connected to load 4; outputs must not exceed the 43 V absolute maximum output voltage."+ },+ {+ "number": "8",+ "name": "nENBL",+ "type": "input",+ "description": "Active-low enable input (internal pulldown); outputs are enabled when driven low and disabled when driven high, with digital input limits of -0.5 V to 7 V."+ },+ {+ "number": "9",+ "name": "RESET",+ "type": "input",+ "description": "Active-high reset input (internal pulldown) that initializes internal logic, clears the overcurrent fault and serial interface registers; digital input limits of -0.5 V to 7 V."+ },+ {+ "number": "10",+ "name": "NC",+ "type": "unconnected",+ "description": "No connection shown in the pin configuration diagram; not listed in the Pin Functions table."+ },+ {+ "number": "11",+ "name": "LATCH",+ "type": "input",+ "description": "Latch input (internal pulldown); a rising edge latches the shift register to the outputs and a falling edge latches fault data, with a minimum pulse width of 200 ns."+ },+ {+ "number": "12",+ "name": "GND",+ "type": "power_in",+ "description": "Device ground; all GND pins must be connected to ground."+ },+ {+ "number": "13",+ "name": "SCLK",+ "type": "input",+ "description": "Serial clock input (internal pulldown); data is shifted in on each rising edge with a minimum clock cycle time of 62 ns."+ },+ {+ "number": "14",+ "name": "SDATIN",+ "type": "input",+ "description": "Serial data input (internal pulldown) sampled on the SCLK rising edge with 5 ns minimum setup time to SCLK."+ },+ {+ "number": "15",+ "name": "SDATOUT",+ "type": "output",+ "description": "Serial data output with push-pull structure and internal pullup, able to drive another DRV8806 SDATIN up to 1 MHz without external pullup; sources about 1 mA and sinks about 5 mA."+ },+ {+ "number": "16",+ "name": "nFAULT",+ "type": "output",+ "description": "Open-drain fault output driven low on overtemperature, overcurrent or open load, with output low voltage of 0.5 V max at 5 mA."+ },+ {+ "number": "17",+ "name": "EP",+ "type": "passive",+ "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: The exposed thermal pad (PowerPAD) is listed as GND in the Pin Functions table but has no numbered p; Conflicting SDATOUT output type: the Pin Functions table says OD (open-drain), while the text and el; Pin 10 (NC) is taken from the top-view pin diagram and the diagram text; it is not described in the ",+ "exposed pad 17 added from the footprint"+ ],+ "pages_sent": 26,+ "cost_usd": 0.1074,+ "at": "2026-10-08T02:50:29"+ },+ "datasheet": {+ "url": "https://www.ti.com/cn/lit/gpn/drv8806",+ "pages": 26,+ "sha256": "ae0b5f785bd9778e",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 17,+ "described": 17,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "drv8806pwpr.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6.4,+ 5,+ 1.1+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "7982746831c0bd23f4690608869ad67776faae5c762fb0376666126a3998921b",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "drv8806pwpr-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6.4,+ 5,+ 1.1+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "ddf1fcece13a84ee7220a4e5b41141f47d535124f40d42b6a8ede49038198e4d",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}