component
DRV2700RGPT
Public Made by Adomby adom
Texas Instruments Power Distribution Switches, QFN-20-EP(4x4). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+58@@ -0,0 +1,58 @@+# DRV2700RGPT++**Texas Instruments** · Power Distribution Switches · QFN-20-EP(4x4)++DRV2700RGPT from Texas Instruments, in a QFN-20-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | PUMP | power_out | Internal charge-pump voltage output. |+| 2 | VDD | power_in | Power supply, connected to the battery; recommended operating range is 3.3 V to 5.5 V. |+| 3 | FB | input | Boost feedback input; the boost output voltage is set by two external resistors R(FB1) and R(FB2) connected to this pin. |+| 4 | GND | power_in | Ground. |+| 5 | GND | power_in | Ground. |+| 6 | GND | power_in | Ground. |+| 7 | SW | power_out | Internal boost switch pin; the boost/output voltage absolute maximum on SW is 120 V. |+| 8 | SW | power_out | Internal boost switch pin; the boost/output voltage absolute maximum on SW is 120 V. |+| 9 | NC | unconnected | No internal connection. |+| 10 | BST | power_out | Boost output voltage; recommended boost voltage range is 15 V to 105 V. |+| 11 | BST | power_out | Boost output voltage; recommended boost voltage range is 15 V to 105 V. |+| 12 | PVDD | power_in | Amplifier supply voltage; the boost/output voltage absolute maximum on PVDD is 120 V. |+| 13 | OUT+ | output | Noninverting amplifier output; the boost/output voltage absolute maximum is 120 V. |+| 14 | OUT- | output | Inverting amplifier output; the boost/output voltage absolute maximum is 120 V. |+| 15 | REXT | input | Resistor to ground that sets the boost current limit; the recommended resistor range is 6 kΩ to 35 kΩ. |+| 16 | IN- | input | Inverting amplifier input; the recommended differential input voltage is 1.8 V. |+| 17 | IN+ | input | Noninverting amplifier input; the recommended differential input voltage is 1.8 V. |+| 18 | GAIN0 | input | Gain programming pin, least significant bit; digital input with VIL maximum 0.75 V and VIH minimum 1.4 V at VDD = 3.6 V. |+| 19 | GAIN1 | input | Gain programming pin, most significant bit; digital input with VIL maximum 0.75 V and VIH minimum 1.4 V at VDD = 3.6 V. |+| 20 | EN | input | Chip enable input; digital input with VIL maximum 0.75 V and VIH minimum 1.4 V at VDD = 3.6 V. |+| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | QFN-20-EP(4x4) |+| Category | Power Management (PMIC) |+| Pins | 21 |++## CAD (KiCad official)++- Symbol: `DRV2700RGPT`+- Footprint: `Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm`+- 3D model: QFN-20-EP(4x4) (KiCad packages3D, STEP)+- 3D model files: `drv2700rgpt-etched.step` / `drv2700rgpt-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `drv2700rgpt.step` / `drv2700rgpt.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/drv2700) (38 pp, sha256 `05241d239a52b292`, retrieved 2026-10-07, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/drv2700rgpt-datasheet.pdf)
page.jsonadded+278@@ -0,0 +1,278 @@+{+ "slug": "drv2700rgpt",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments Power Distribution Switches, QFN-20-EP(4x4). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "power management (pmic)",+ "drv2700rgpt",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "drv2700rgpt.kicad_sym",+ "drv2700rgpt.kicad_mod",+ "drv2700rgpt.glb",+ "drv2700rgpt.step",+ "drv2700rgpt.lbr",+ "docs/hero.png",+ "docs/drv2700rgpt-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "drv2700rgpt-hero.glb",+ "drv2700rgpt-hero.overlay.json"+ ],+ "component": {+ "mpn": "DRV2700RGPT",+ "manufacturer": "Texas Instruments",+ "package": "QFN-20-EP(4x4)",+ "pin_count": 21,+ "category": "Power Management (PMIC)",+ "subcategory": "Power Distribution Switches",+ "datasheet": "https://www.ti.com/cn/lit/gpn/drv2700",+ "parts": {+ "symbol": "drv2700rgpt.kicad_sym",+ "footprint": "drv2700rgpt.kicad_mod",+ "model_3d": "drv2700rgpt-hero.glb",+ "model_3d_plain": "drv2700rgpt.glb",+ "model_3d_step": "drv2700rgpt-etched.step",+ "model_3d_step_plain": "drv2700rgpt.step",+ "lbr": "drv2700rgpt.lbr"+ },+ "distributor_links": {+ "lcsc": "C2150456",+ "digikey": "296-41118-2-ND",+ "mouser": "595-DRV2700RGPT"+ },+ "distributor_check": {+ "checked_at": "2026-10-07T22:24:41Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "296-41118-2-ND",+ "status": "found"+ },+ "mouser": {+ "pn": "595-DRV2700RGPT",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "PUMP",+ "type": "power_out",+ "description": "Internal charge-pump voltage output."+ },+ {+ "number": "2",+ "name": "VDD",+ "type": "power_in",+ "description": "Power supply, connected to the battery; recommended operating range is 3.3 V to 5.5 V."+ },+ {+ "number": "3",+ "name": "FB",+ "type": "input",+ "description": "Boost feedback input; the boost output voltage is set by two external resistors R(FB1) and R(FB2) connected to this pin."+ },+ {+ "number": "4",+ "name": "GND",+ "type": "power_in",+ "description": "Ground."+ },+ {+ "number": "5",+ "name": "GND",+ "type": "power_in",+ "description": "Ground."+ },+ {+ "number": "6",+ "name": "GND",+ "type": "power_in",+ "description": "Ground."+ },+ {+ "number": "7",+ "name": "SW",+ "type": "power_out",+ "description": "Internal boost switch pin; the boost/output voltage absolute maximum on SW is 120 V."+ },+ {+ "number": "8",+ "name": "SW",+ "type": "power_out",+ "description": "Internal boost switch pin; the boost/output voltage absolute maximum on SW is 120 V."+ },+ {+ "number": "9",+ "name": "NC",+ "type": "unconnected",+ "description": "No internal connection."+ },+ {+ "number": "10",+ "name": "BST",+ "type": "power_out",+ "description": "Boost output voltage; recommended boost voltage range is 15 V to 105 V."+ },+ {+ "number": "11",+ "name": "BST",+ "type": "power_out",+ "description": "Boost output voltage; recommended boost voltage range is 15 V to 105 V."+ },+ {+ "number": "12",+ "name": "PVDD",+ "type": "power_in",+ "description": "Amplifier supply voltage; the boost/output voltage absolute maximum on PVDD is 120 V."+ },+ {+ "number": "13",+ "name": "OUT+",+ "type": "output",+ "description": "Noninverting amplifier output; the boost/output voltage absolute maximum is 120 V."+ },+ {+ "number": "14",+ "name": "OUT-",+ "type": "output",+ "description": "Inverting amplifier output; the boost/output voltage absolute maximum is 120 V."+ },+ {+ "number": "15",+ "name": "REXT",+ "type": "input",+ "description": "Resistor to ground that sets the boost current limit; the recommended resistor range is 6 kΩ to 35 kΩ."+ },+ {+ "number": "16",+ "name": "IN-",+ "type": "input",+ "description": "Inverting amplifier input; the recommended differential input voltage is 1.8 V."+ },+ {+ "number": "17",+ "name": "IN+",+ "type": "input",+ "description": "Noninverting amplifier input; the recommended differential input voltage is 1.8 V."+ },+ {+ "number": "18",+ "name": "GAIN0",+ "type": "input",+ "description": "Gain programming pin, least significant bit; digital input with VIL maximum 0.75 V and VIH minimum 1.4 V at VDD = 3.6 V."+ },+ {+ "number": "19",+ "name": "GAIN1",+ "type": "input",+ "description": "Gain programming pin, most significant bit; digital input with VIL maximum 0.75 V and VIH minimum 1.4 V at VDD = 3.6 V."+ },+ {+ "number": "20",+ "name": "EN",+ "type": "input",+ "description": "Chip enable input; digital input with VIL maximum 0.75 V and VIH minimum 1.4 V at VDD = 3.6 V."+ },+ {+ "number": "21",+ "name": "EP",+ "type": "passive",+ "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: The datasheet lists an exposed thermal pad on the RGP package but gives it no pin number in the pin ; The pin table text was extracted with its layout scrambled. Pin numbers were mapped from the page 3 ; KiCad types for PUMP, BST, SW and PVDD were chosen by me from the datasheet's 'P' (power) designatio",+ "exposed pad 21 added from the footprint"+ ],+ "pages_sent": 7,+ "cost_usd": 0.0605,+ "at": "2026-10-07T22:24:26"+ },+ "datasheet": {+ "url": "https://www.ti.com/cn/lit/gpn/drv2700",+ "pages": 38,+ "sha256": "05241d239a52b292",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 21,+ "described": 21,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "drv2700rgpt.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 4,+ 4,+ 0.77+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "c9476a1612023de37f27b4972110ab6ac6dc0eaf5ac48957a2e1c497650082a5",+ "checked": "2026-10-07",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "drv2700rgpt-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 4,+ 4,+ 0.77+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "397e03237c7392c4fe558c96fc9b049e9d0c1602fcaf1de958fe6d61215f1432",+ "checked": "2026-10-07",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}