component
DAC8760IRHAR
Public Made by Adomby adom
Texas Instruments Digital To Analog Converters (DAC), VQFN-40-EP(6x6). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+78@@ -0,0 +1,78 @@+# DAC8760IRHAR++**Texas Instruments** · Digital To Analog Converters (DAC) · VQFN-40-EP(6x6)++DAC8760IRHAR from Texas Instruments, in a VQFN-40-EP(6x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | NC | unconnected | Not used. |+| 2 | ALARM | output | Open-drain digital output (active low) for alarm detection; requires external 10 kΩ pullup resistor. |+| 3 | GND | power_in | Ground reference for digital circuitry; connect to 0 V. |+| 4 | CLR-SEL | input | Digital input selecting VOUT value in CLEAR state after power-on reset. |+| 5 | CLR | input | Active-high digital input forcing device into CLEAR state. |+| 6 | LATCH | input | Digital input loading input shift register data into DAC registers on rising edge. |+| 7 | SCLK | input | Digital Schmitt-Trigger SPI serial clock input supporting data rates up to 30 MHz. |+| 8 | DIN | input | Digital Schmitt-Trigger input for serial data clocked into 24-bit shift register on SCLK rising edge. |+| 9 | SDO | output | Digital output for serial data valid on SCLK rising edge. |+| 10 | NC | unconnected | Not used. |+| 11 | NC | unconnected | Not used. |+| 12 | GND | power_in | Ground reference for digital and analog circuitry; connect to 0 V. |+| 13 | GND | power_in | Ground reference for analog circuitry; connect to 0 V. |+| 14 | AVSS | power_in | Negative analog power supply (-18 V to 0 V in dual mode) or connected to GND in single power-supply operation. |+| 15 | GND | power_in | Ground reference for analog circuitry; connect to 0 V. |+| 16 | ISET-R | input | Analog input for external precision resistor connection (15 kΩ recommended). |+| 17 | REFOUT | output | Analog output for internal reference voltage (5 V nominal); connect to REFIN when using internal reference. |+| 18 | REFIN | input | Analog input for reference voltage with range 4.95 V to 5.05 V and external current limit of 30 µA. |+| 19 | NC | unconnected | Not used. |+| 20 | NC | unconnected | Not used. |+| 21 | NC | unconnected | Not used. |+| 22 | NC | unconnected | Not used. |+| 23 | DVDD-EN | input | Digital input enabling/disabling internal power supply; connect to GND to disable or leave floating to enable. |+| 24 | CMP | output | Analog output for optional external compensation capacitor connection improving output amplifier stability with high capacitive loads. |+| 25 | HART-IN | input | Analog input pin for HART modulation signal. |+| 26 | IOUT | output | Analog current output pin with programmable range 4-20 mA, 0-20 mA, or 0-24 mA and loop compliance voltage of AVDD - 2 V. |+| 27 | BOOST | output | Analog output for optional external transistor connection. |+| 28 | CAP1 | input | Analog input for optional current output filtering capacitor connection. |+| 29 | CAP2 | input | Analog input for optional current output filtering capacitor connection. |+| 30 | NC | unconnected | Not used. |+| 31 | NC | unconnected | Not used. |+| 32 | VOUT | output | Analog buffered voltage output pin with programmable range 0-5V, 0-10V, ±5V, ±10V or overvoltage variants 0-5.5V, 0-11V, ±5.5V, ±11V. |+| 33 | +VSENSE | input | Analog sense input for positive voltage output load connection. |+| 34 | -VSENSE | input | Analog sense input for negative voltage output load connection. |+| 35 | NC | unconnected | Not used. |+| 36 | AVDD | power_in | Positive analog power supply input with range 10 V to 36 V (when AVDD + |AVSS| ≤ 36 V). |+| 37 | AVSS | power_in | Negative analog power supply (-18 V to 0 V when AVDD + |AVSS| ≤ 36 V) or connected to GND in single power-supply operation. |+| 38 | NC | unconnected | Not used. |+| 39 | DVDD | power_in | Digital power supply functioning as input (2.7 V to 5.5 V when internal regulator disabled via DVDD-EN to GND) or output (internal regulator enabled when DVDD-EN floating). |+| 40 | NC | unconnected | Not used. |+| 41 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | VQFN-40-EP(6x6) |+| Category | Data Acquisition |+| Pins | 41 |++## CAD (KiCad official)++- Symbol: `DAC8760IRHAR`+- Footprint: `Package_DFN_QFN:QFN-40-1EP_6x6mm_P0.5mm_EP4.6x4.6mm`+- 3D model: VQFN-40-EP(6x6) (KiCad packages3D, STEP)+- 3D model files: `dac8760irhar-etched.step` / `dac8760irhar-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `dac8760irhar.step` / `dac8760irhar.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/dac8760) (73 pp, sha256 `dcefca4e28752db2`, retrieved 2026-10-01, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/dac8760irhar-datasheet.pdf)
page.jsonadded+356@@ -0,0 +1,356 @@+{+ "slug": "dac8760irhar",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments Digital To Analog Converters (DAC), VQFN-40-EP(6x6). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "data acquisition",+ "dac8760irhar",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "dac8760irhar.kicad_sym",+ "dac8760irhar.kicad_mod",+ "dac8760irhar.glb",+ "dac8760irhar.step",+ "dac8760irhar.lbr",+ "docs/hero.png",+ "docs/dac8760irhar-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ],+ "component": {+ "mpn": "DAC8760IRHAR",+ "manufacturer": "Texas Instruments",+ "package": "VQFN-40-EP(6x6)",+ "pin_count": 41,+ "category": "Data Acquisition",+ "subcategory": "Digital To Analog Converters (DAC)",+ "datasheet": "https://www.ti.com/cn/lit/gpn/dac8760",+ "parts": {+ "symbol": "dac8760irhar.kicad_sym",+ "footprint": "dac8760irhar.kicad_mod",+ "model_3d": "dac8760irhar-etched.glb",+ "model_3d_plain": "dac8760irhar.glb",+ "model_3d_step": "dac8760irhar-etched.step",+ "model_3d_step_plain": "dac8760irhar.step",+ "lbr": "dac8760irhar.lbr"+ },+ "distributor_links": {+ "lcsc": "C2651673",+ "digikey": "296-37282-2-ND",+ "mouser": "595-DAC8760IRHAR"+ },+ "distributor_check": {+ "checked_at": "2026-10-01T04:00:20Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "296-37282-2-ND",+ "status": "found"+ },+ "mouser": {+ "pn": "595-DAC8760IRHAR",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "NC",+ "type": "unconnected",+ "description": "Not used."+ },+ {+ "number": "2",+ "name": "ALARM",+ "type": "output",+ "description": "Open-drain digital output (active low) for alarm detection; requires external 10 kΩ pullup resistor."+ },+ {+ "number": "3",+ "name": "GND",+ "type": "power_in",+ "description": "Ground reference for digital circuitry; connect to 0 V."+ },+ {+ "number": "4",+ "name": "CLR-SEL",+ "type": "input",+ "description": "Digital input selecting VOUT value in CLEAR state after power-on reset."+ },+ {+ "number": "5",+ "name": "CLR",+ "type": "input",+ "description": "Active-high digital input forcing device into CLEAR state."+ },+ {+ "number": "6",+ "name": "LATCH",+ "type": "input",+ "description": "Digital input loading input shift register data into DAC registers on rising edge."+ },+ {+ "number": "7",+ "name": "SCLK",+ "type": "input",+ "description": "Digital Schmitt-Trigger SPI serial clock input supporting data rates up to 30 MHz."+ },+ {+ "number": "8",+ "name": "DIN",+ "type": "input",+ "description": "Digital Schmitt-Trigger input for serial data clocked into 24-bit shift register on SCLK rising edge."+ },+ {+ "number": "9",+ "name": "SDO",+ "type": "output",+ "description": "Digital output for serial data valid on SCLK rising edge."+ },+ {+ "number": "10",+ "name": "NC",+ "type": "unconnected",+ "description": "Not used."+ },+ {+ "number": "11",+ "name": "NC",+ "type": "unconnected",+ "description": "Not used."+ },+ {+ "number": "12",+ "name": "GND",+ "type": "power_in",+ "description": "Ground reference for digital and analog circuitry; connect to 0 V."+ },+ {+ "number": "13",+ "name": "GND",+ "type": "power_in",+ "description": "Ground reference for analog circuitry; connect to 0 V."+ },+ {+ "number": "14",+ "name": "AVSS",+ "type": "power_in",+ "description": "Negative analog power supply (-18 V to 0 V in dual mode) or connected to GND in single power-supply operation."+ },+ {+ "number": "15",+ "name": "GND",+ "type": "power_in",+ "description": "Ground reference for analog circuitry; connect to 0 V."+ },+ {+ "number": "16",+ "name": "ISET-R",+ "type": "input",+ "description": "Analog input for external precision resistor connection (15 kΩ recommended)."+ },+ {+ "number": "17",+ "name": "REFOUT",+ "type": "output",+ "description": "Analog output for internal reference voltage (5 V nominal); connect to REFIN when using internal reference."+ },+ {+ "number": "18",+ "name": "REFIN",+ "type": "input",+ "description": "Analog input for reference voltage with range 4.95 V to 5.05 V and external current limit of 30 µA."+ },+ {+ "number": "19",+ "name": "NC",+ "type": "unconnected",+ "description": "Not used."+ },+ {+ "number": "20",+ "name": "NC",+ "type": "unconnected",+ "description": "Not used."+ },+ {+ "number": "21",+ "name": "NC",+ "type": "unconnected",+ "description": "Not used."+ },+ {+ "number": "22",+ "name": "NC",+ "type": "unconnected",+ "description": "Not used."+ },+ {+ "number": "23",+ "name": "DVDD-EN",+ "type": "input",+ "description": "Digital input enabling/disabling internal power supply; connect to GND to disable or leave floating to enable."+ },+ {+ "number": "24",+ "name": "CMP",+ "type": "output",+ "description": "Analog output for optional external compensation capacitor connection improving output amplifier stability with high capacitive loads."+ },+ {+ "number": "25",+ "name": "HART-IN",+ "type": "input",+ "description": "Analog input pin for HART modulation signal."+ },+ {+ "number": "26",+ "name": "IOUT",+ "type": "output",+ "description": "Analog current output pin with programmable range 4-20 mA, 0-20 mA, or 0-24 mA and loop compliance voltage of AVDD - 2 V."+ },+ {+ "number": "27",+ "name": "BOOST",+ "type": "output",+ "description": "Analog output for optional external transistor connection."+ },+ {+ "number": "28",+ "name": "CAP1",+ "type": "input",+ "description": "Analog input for optional current output filtering capacitor connection."+ },+ {+ "number": "29",+ "name": "CAP2",+ "type": "input",+ "description": "Analog input for optional current output filtering capacitor connection."+ },+ {+ "number": "30",+ "name": "NC",+ "type": "unconnected",+ "description": "Not used."+ },+ {+ "number": "31",+ "name": "NC",+ "type": "unconnected",+ "description": "Not used."+ },+ {+ "number": "32",+ "name": "VOUT",+ "type": "output",+ "description": "Analog buffered voltage output pin with programmable range 0-5V, 0-10V, ±5V, ±10V or overvoltage variants 0-5.5V, 0-11V, ±5.5V, ±11V."+ },+ {+ "number": "33",+ "name": "+VSENSE",+ "type": "input",+ "description": "Analog sense input for positive voltage output load connection."+ },+ {+ "number": "34",+ "name": "–VSENSE",+ "type": "input",+ "description": "Analog sense input for negative voltage output load connection."+ },+ {+ "number": "35",+ "name": "NC",+ "type": "unconnected",+ "description": "Not used."+ },+ {+ "number": "36",+ "name": "AVDD",+ "type": "power_in",+ "description": "Positive analog power supply input with range 10 V to 36 V (when AVDD + |AVSS| ≤ 36 V)."+ },+ {+ "number": "37",+ "name": "AVSS",+ "type": "power_in",+ "description": "Negative analog power supply (-18 V to 0 V when AVDD + |AVSS| ≤ 36 V) or connected to GND in single power-supply operation."+ },+ {+ "number": "38",+ "name": "NC",+ "type": "unconnected",+ "description": "Not used."+ },+ {+ "number": "39",+ "name": "DVDD",+ "type": "power_in",+ "description": "Digital power supply functioning as input (2.7 V to 5.5 V when internal regulator disabled via DVDD-EN to GND) or output (internal regulator enabled when DVDD-EN floating)."+ },+ {+ "number": "40",+ "name": "NC",+ "type": "unconnected",+ "description": "Not used."+ },+ {+ "number": "41",+ "name": "EP",+ "type": "passive",+ "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-4-5-20251001",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: Pin 39 (DVDD) has dual functionality: serves as power input when external supply is required (DVDD-E",+ "exposed pad 41 added from the footprint"+ ],+ "pages_sent": 11,+ "cost_usd": 0.1848,+ "at": "2026-10-01T04:00:02"+ },+ "datasheet": {+ "url": "https://www.ti.com/cn/lit/gpn/dac8760",+ "pages": 73,+ "sha256": "dcefca4e28752db2",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 41,+ "described": 41,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ }+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}