component
BTS723GW
Public Made by Adomby adom
Infineon AC-DC Controllers and Regulators, SOIC-14. Pinout extracted from the datasheet, KiCad symbol/footprint/3D.
← Commit history
page.json+12−9@@ -38,31 +38,31 @@ "number": "2", "name": "IN1", "type": "input",- "description": "Input for channel 1: activates channel 1 on logic-high signal. CMOS-compatible, ground-referenced with integrated 20 k\u03a9 input series resistor. Absolute max input voltage \u00b142 V DC; max input current \u00b12.0 mA DC."+ "description": "Input for channel 1: activates channel 1 on logic-high signal. CMOS-compatible, ground-referenced with integrated 20 kΩ input series resistor. Absolute max input voltage ±42 V DC; max input current ±2.0 mA DC." }, { "number": "3", "name": "ST1", "type": "output",- "description": "Diagnostic feedback for channel 1: open-drain status output. Integrated pull-up via SPU pin; reports open-load (OFF state) and thermal shutdown (ON state). Max status current \u00b12.0 mA DC."+ "description": "Diagnostic feedback for channel 1: open-drain status output. Integrated pull-up via SPU pin; reports open-load (OFF state) and thermal shutdown (ON state). Max status current ±2.0 mA DC." }, { "number": "4", "name": "GND", "type": "power_in",- "description": "Logic ground. Independent from load ground. External current-limit resistor (150 \u03a9 recommended) advised for Vbb > Vbb(AZ)."+ "description": "Logic ground. Independent from load ground. External current-limit resistor (150 Ω recommended) advised for Vbb > Vbb(AZ)." }, { "number": "5", "name": "ST2", "type": "output",- "description": "Diagnostic feedback for channel 2: open-drain status output. Integrated pull-up via SPU pin; reports open-load (OFF state) and thermal shutdown (ON state). Max status current \u00b12.0 mA DC."+ "description": "Diagnostic feedback for channel 2: open-drain status output. Integrated pull-up via SPU pin; reports open-load (OFF state) and thermal shutdown (ON state). Max status current ±2.0 mA DC." }, { "number": "6", "name": "IN2", "type": "input",- "description": "Input for channel 2: activates channel 2 on logic-high signal. CMOS-compatible, ground-referenced with integrated 20 k\u03a9 input series resistor. Absolute max input voltage \u00b142 V DC; max input current \u00b12.0 mA DC."+ "description": "Input for channel 2: activates channel 2 on logic-high signal. CMOS-compatible, ground-referenced with integrated 20 kΩ input series resistor. Absolute max input voltage ±42 V DC; max input current ±2.0 mA DC." }, { "number": "7",@@ -80,7 +80,7 @@ "number": "9", "name": "OUT2", "type": "power_out",- "description": "Protected high-side power output of channel 2. On-state resistance ~90 m\u03a9 typ (each channel, Tj=25\u00b0C); nominal load current 2.9 A (one channel active); current limitation 8 A. Pins 9 and 10 must be connected in parallel for spec operation."+ "description": "Protected high-side power output of channel 2. On-state resistance ~90 mΩ typ (each channel, Tj=25°C); nominal load current 2.9 A (one channel active); current limitation 8 A. Pins 9 and 10 must be connected in parallel for spec operation." }, { "number": "10",@@ -92,13 +92,13 @@ "number": "11", "name": "SPU", "type": "input",- "description": "Status Pull-Up: connection for external pull-up voltage source (max \u00b142 V DC) for the open-drain ST1/ST2 status outputs. Pull-up resistors (~12 k\u03a9 / 850 \u03a9 network) are integrated internally."+ "description": "Status Pull-Up: connection for external pull-up voltage source (max ±42 V DC) for the open-drain ST1/ST2 status outputs. Pull-up resistors (~12 kΩ / 850 Ω network) are integrated internally." }, { "number": "12", "name": "OUT1", "type": "power_out",- "description": "Protected high-side power output of channel 1. On-state resistance ~90 m\u03a9 typ (each channel, Tj=25\u00b0C); nominal load current 2.9 A (one channel active); current limitation 8 A. Pins 12 and 13 must be connected in parallel for spec operation."+ "description": "Protected high-side power output of channel 1. On-state resistance ~90 mΩ typ (each channel, Tj=25°C); nominal load current 2.9 A (one channel active); current limitation 8 A. Pins 12 and 13 must be connected in parallel for spec operation." }, { "number": "13",@@ -174,5 +174,8 @@ "docs/bts723gw-datasheet.pdf", "viewers/symbol.html", "viewers/footprint.html"- ]+ ],+ "visibility": {+ "public": true+ } }