← Commit history

Initial commit: component/bq25895mrtwr

Ray ·cae081c2c5 ·
2 files changed +322
README.mdadded+62
@@ -0,0 +1,62 @@+# BQ25895MRTWR++**Texas Instruments** · Battery Management · WQFN-24-EP(4x4)++BQ25895MRTWR from Texas Instruments, in a WQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VBUS | power_in | Input voltage from adapter, 3.9V to 14V; reverse-blocking MOSFET to PMID. |+| 2 | D+ | bidirectional | USB positive data line; BC1.2 detection and MaxCharge™ adapter identification. |+| 3 | D- | bidirectional | USB negative data line; BC1.2 detection and MaxCharge™ adapter identification. |+| 4 | STAT | output | Open-drain output: LOW=charging, HIGH=complete/disabled, 1Hz blink=fault condition. |+| 5 | SCL | input | I2C clock input with required 10 kΩ pull-up resistor. |+| 6 | SDA | bidirectional | I2C data input/output with required 10 kΩ pull-up resistor. |+| 7 | INT | output | Open-drain interrupt output; 256 µs active-low pulse on status/fault event. |+| 8 | OTG | input | Boost mode enable; activates when high and no VBUS present; output 5V at 3.1A. |+| 9 | CE | input | Active-low charge enable; charging requires CHG_CONFIG=1 and CE pin low. |+| 10 | ILIM | input | Analog input for current limit; regulated at 0.8V with external resistor to ground. |+| 11 | TS | input | Thermistor input; charging suspends when voltage outside programmed temperature range. |+| 12 | QON | input | BATFET control; logic low exits shipping mode or triggers system reset when VBUS absent. |+| 13 | BAT | power_in | Battery positive terminal; supports 2.5V to 5.0V with internal BATFET to SYS. |+| 14 | BAT | power_in | Battery positive terminal; supports 2.5V to 5.0V with internal BATFET to SYS. |+| 15 | SYS | power_out | System power output regulated above 3.5V minimum; supplied by battery through BATFET. |+| 16 | SYS | power_out | System power output regulated above 3.5V minimum; supplied by battery through BATFET. |+| 17 | PGND | power_in | Power ground for high-current converter; connected to LSFET source. |+| 18 | PGND | power_in | Power ground for high-current converter; connected to LSFET source. |+| 19 | SW | passive | Switching node connecting HSFET source and LSFET drain; 0.047 µF bootstrap capacitor to BTST required. |+| 20 | SW | passive | Switching node connecting HSFET source and LSFET drain; 0.047 µF bootstrap capacitor to BTST required. |+| 21 | BTST | power_in | Bootstrap supply for high-side driver; connected to boost-strap diode anode. |+| 22 | REGN | power_out | Gate driver supply output; requires 4.7 µF ceramic capacitor to ground. |+| 23 | PMID | power_out | Boost mode output (5V default) supplying external load at up to 3.1A; requires 40-60 µF to ground. |+| 24 | DSEL | output | Open-drain D+/D- detection control; low during detection and for MaxCharge™ adapter. |+| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | WQFN-24-EP(4x4) |+| Category | Power Management (PMIC) |+| Pins | 25 |++## CAD (KiCad official)++- Symbol: `BQ25895MRTWR`+- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm`+- 3D model: WQFN-24-EP(4x4) (KiCad packages3D, STEP)+- 3D model files: `bq25895mrtwr-etched.step` / `bq25895mrtwr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `bq25895mrtwr.step` / `bq25895mrtwr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/bq25895m) (66 pp, sha256 `56e2dea86165cdcd`, retrieved 2026-10-01, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/bq25895mrtwr-datasheet.pdf)
page.jsonadded+260
@@ -0,0 +1,260 @@+{+  "slug": "bq25895mrtwr",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments Battery Management, WQFN-24-EP(4x4). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "bq25895mrtwr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "bq25895mrtwr.kicad_sym",+    "bq25895mrtwr.kicad_mod",+    "bq25895mrtwr.glb",+    "bq25895mrtwr.step",+    "bq25895mrtwr.lbr",+    "docs/hero.png",+    "docs/bq25895mrtwr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "BQ25895MRTWR",+    "manufacturer": "Texas Instruments",+    "package": "WQFN-24-EP(4x4)",+    "pin_count": 25,+    "category": "Power Management (PMIC)",+    "subcategory": "Battery Management",+    "datasheet": "https://www.ti.com/cn/lit/gpn/bq25895m",+    "parts": {+      "symbol": "bq25895mrtwr.kicad_sym",+      "footprint": "bq25895mrtwr.kicad_mod",+      "model_3d": "bq25895mrtwr-etched.glb",+      "model_3d_plain": "bq25895mrtwr.glb",+      "model_3d_step": "bq25895mrtwr-etched.step",+      "model_3d_step_plain": "bq25895mrtwr.step",+      "lbr": "bq25895mrtwr.lbr"+    },+    "distributor_links": {+      "lcsc": "C485917",+      "digikey": "296-42447-2-ND",+      "mouser": "595-BQ25895MRTWR"+    },+    "distributor_check": {+      "checked_at": "2026-10-01T01:13:00Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "296-42447-2-ND",+        "status": "found",+        "lifecycle": "Active"+      },+      "mouser": {+        "pn": "595-BQ25895MRTWR",+        "status": "found"+      }+    },+    "pins": [+      {+        "number": "1",+        "name": "VBUS",+        "type": "power_in",+        "description": "Input voltage from adapter, 3.9V to 14V; reverse-blocking MOSFET to PMID."+      },+      {+        "number": "2",+        "name": "D+",+        "type": "bidirectional",+        "description": "USB positive data line; BC1.2 detection and MaxCharge™ adapter identification."+      },+      {+        "number": "3",+        "name": "D–",+        "type": "bidirectional",+        "description": "USB negative data line; BC1.2 detection and MaxCharge™ adapter identification."+      },+      {+        "number": "4",+        "name": "STAT",+        "type": "output",+        "description": "Open-drain output: LOW=charging, HIGH=complete/disabled, 1Hz blink=fault condition."+      },+      {+        "number": "5",+        "name": "SCL",+        "type": "input",+        "description": "I2C clock input with required 10 kΩ pull-up resistor."+      },+      {+        "number": "6",+        "name": "SDA",+        "type": "bidirectional",+        "description": "I2C data input/output with required 10 kΩ pull-up resistor."+      },+      {+        "number": "7",+        "name": "INT",+        "type": "output",+        "description": "Open-drain interrupt output; 256 µs active-low pulse on status/fault event."+      },+      {+        "number": "8",+        "name": "OTG",+        "type": "input",+        "description": "Boost mode enable; activates when high and no VBUS present; output 5V at 3.1A."+      },+      {+        "number": "9",+        "name": "CE",+        "type": "input",+        "description": "Active-low charge enable; charging requires CHG_CONFIG=1 and CE pin low."+      },+      {+        "number": "10",+        "name": "ILIM",+        "type": "input",+        "description": "Analog input for current limit; regulated at 0.8V with external resistor to ground."+      },+      {+        "number": "11",+        "name": "TS",+        "type": "input",+        "description": "Thermistor input; charging suspends when voltage outside programmed temperature range."+      },+      {+        "number": "12",+        "name": "QON",+        "type": "input",+        "description": "BATFET control; logic low exits shipping mode or triggers system reset when VBUS absent."+      },+      {+        "number": "13",+        "name": "BAT",+        "type": "power_in",+        "description": "Battery positive terminal; supports 2.5V to 5.0V with internal BATFET to SYS."+      },+      {+        "number": "14",+        "name": "BAT",+        "type": "power_in",+        "description": "Battery positive terminal; supports 2.5V to 5.0V with internal BATFET to SYS."+      },+      {+        "number": "15",+        "name": "SYS",+        "type": "power_out",+        "description": "System power output regulated above 3.5V minimum; supplied by battery through BATFET."+      },+      {+        "number": "16",+        "name": "SYS",+        "type": "power_out",+        "description": "System power output regulated above 3.5V minimum; supplied by battery through BATFET."+      },+      {+        "number": "17",+        "name": "PGND",+        "type": "power_in",+        "description": "Power ground for high-current converter; connected to LSFET source."+      },+      {+        "number": "18",+        "name": "PGND",+        "type": "power_in",+        "description": "Power ground for high-current converter; connected to LSFET source."+      },+      {+        "number": "19",+        "name": "SW",+        "type": "passive",+        "description": "Switching node connecting HSFET source and LSFET drain; 0.047 µF bootstrap capacitor to BTST required."+      },+      {+        "number": "20",+        "name": "SW",+        "type": "passive",+        "description": "Switching node connecting HSFET source and LSFET drain; 0.047 µF bootstrap capacitor to BTST required."+      },+      {+        "number": "21",+        "name": "BTST",+        "type": "power_in",+        "description": "Bootstrap supply for high-side driver; connected to boost-strap diode anode."+      },+      {+        "number": "22",+        "name": "REGN",+        "type": "power_out",+        "description": "Gate driver supply output; requires 4.7 µF ceramic capacitor to ground."+      },+      {+        "number": "23",+        "name": "PMID",+        "type": "power_out",+        "description": "Boost mode output (5V default) supplying external load at up to 3.1A; requires 40-60 µF to ground."+      },+      {+        "number": "24",+        "name": "DSEL",+        "type": "output",+        "description": "Open-drain D+/D- detection control; low during detection and for MaxCharge™ adapter."+      },+      {+        "number": "25",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.3",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.3",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "exposed pad 25 added from the footprint"+        ],+        "pages_sent": 21,+        "cost_usd": 0.24,+        "at": "2026-10-01T01:12:43"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/bq25895m",+        "pages": 66,+        "sha256": "56e2dea86165cdcd",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 25,+        "described": 25,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file