BQ24210DQCR

@@ -1,13 +1,154 @@ {+  "schema_version": 1,+  "type": "component",   "slug": "bq24210dqcr",+  "title": "BQ24210DQCR",+  "brief": "Texas Instruments Battery Management, WSON-10-EP(2x3). Datasheet-verified pinout, KiCad symbol/footprint/3D.",   "version": "0.1.0",-  "type": "component",-  "description": "Texas Instruments Battery Management, WSON-10-EP(2x3). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "license": "CC-BY-SA-4.0",   "tags": [     "component",     "pmic",     "bq24210dqcr"   ],+  "component": {+    "mpn": "BQ24210DQCR",+    "manufacturer": "Texas Instruments",+    "package": "WSON-10-EP(2x3)",+    "pin_count": 11,+    "category": "PMIC",+    "subcategory": "Battery Management",+    "datasheet": "https://www.ti.com/lit/ds/symlink/bq24210dqcr.pdf",+    "parts": {+      "symbol": "bq24210dqcr.kicad_sym",+      "footprint": "bq24210dqcr.kicad_mod",+      "model_3d": "bq24210dqcr.glb",+      "model_3d_step": "bq24210dqcr.step",+      "lbr": "bq24210dqcr.lbr"+    },+    "distributor_links": {},+    "pins": [+      {+        "number": "1",+        "name": "VBUS",+        "type": "power_in",+        "description": "Charging-mode input from external DC supply (solar panel, inductive charging pad, or wall adapter); operating range 3.5-7.0 V (absolute max 20 V with OVP at ~7.5 V). In load mode, this pin becomes a current-limited output at battery voltage. Bypass with 1-10 uF to VSS."+      },+      {+        "number": "2",+        "name": "ISET",+        "type": "input",+        "description": "Fast-charge current programming pin. External resistor from ISET to VSS (675 \u03a9 to 10.8 k\u03a9) sets the fast-charge current up to 800 mA."+      },+      {+        "number": "3",+        "name": "VSS",+        "type": "power_in",+        "description": "Device ground terminal. Must be connected to ground at all times; thermal pad must tie to the same potential as VSS but must not be used as the primary ground input."+      },+      {+        "number": "4",+        "name": "VTSB",+        "type": "power_out",+        "description": "TS bias reference voltage output, regulated and only enabled during charge. No external capacitor required from VTSB to VSS (optional up to 0.1 uF)."+      },+      {+        "number": "5",+        "name": "TS",+        "type": "input",+        "description": "Temperature sense input; connect to NTC thermistor in the battery pack. Valid charging window is 12%-57% of VTSB. Pulling TS high places the part in limited power charging mode; must not be left floating."+      },+      {+        "number": "6",+        "name": "PG",+        "type": "output",+        "description": "Active-low Power-Good indication (open-drain). Pulls low (FET ON) when input voltage is in the normal range (VBUS>BAT and VBUS>UVLO); high-impedance otherwise. Max sink current 15 mA."+      },+      {+        "number": "7",+        "name": "EN",+        "type": "input",+        "description": "Active-low chip enable. Low enables charge or load mode; high places device in suspend mode."+      },+      {+        "number": "8",+        "name": "CHG",+        "type": "output",+        "description": "Active-low charge status indication (open-drain). Pulls low (FET ON) to indicate charging; high-impedance in other cases. Max sink current 15 mA."+      },+      {+        "number": "9",+        "name": "VDPM",+        "type": "input",+        "description": "Programs the input voltage regulation (VBUS_DPM) threshold via a 1 k\u03a9-10 k\u03a9 resistor from VDPM to VSS. When left floating, the VIN DPM loop operates in battery tracking mode (threshold = BAT+100 mV if BAT>3.6 V, else 3.7 V). Must be programmed above the battery voltage."+      },+      {+        "number": "10",+        "name": "BAT",+        "type": "power_out",+        "description": "Battery connection; system load may be connected here. Delivers up to 800 mA charge current with 1% voltage regulation accuracy; short-circuit protected. Bypass with 1-10 uF to VSS."+      },+      {+        "number": "11",+        "name": "EP",+        "type": "passive",+        "description": "Exposed thermal pad on the package underside. Internally connected to VSS; must be soldered to a PCB pad at the same potential as VSS for thermal performance. Do not use as the primary ground input; VSS pin must always be connected to ground."+      }+    ],+    "provenance": {+      "extractor": "ds2sf",+      "datasheet": {+        "url": "https://www.ti.com/lit/ds/symlink/bq24210dqcr.pdf",+        "pages": 32,+        "sha256": "c0743e68a1b201c0",+        "source_tier": "mfr"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 11,+        "described": 11,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "metadata": {+    "specs": {+      "Manufacturer": "Texas Instruments",+      "Package": "WSON-10-EP(2x3)",+      "Category": "PMIC",+      "Pins": "11"+    }+  },+  "variants": [+    {+      "mpn": "BQ24210DQCR",+      "kind": "packaging"+    },+    {+      "mpn": "BQ24210DQCRDQCT",+      "kind": "packaging"+    }+  ],+  "sections": [+    "hero",+    "viewers",+    "readme",+    "breadcrumbs",+    "info"+  ],+  "discovery_triggers": [+    "bq24210dqcr"+  ],+  "discovery_pitch": "BQ24210DQCR (Texas Instruments) component page with datasheet-verified CAD.",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  },   "dependencies": {},   "hero": {     "type": "image",@@ -25,10 +166,5 @@     "docs/bq24210dqcr-datasheet.pdf",     "viewers/symbol.html",     "viewers/footprint.html"-  ],-  "visibility": "public",-  "author": {-    "name": "Ray",-    "email": "[email protected]"-  }+  ] }\ No newline at end of file