BQ24045DSQR

@@ -1,13 +1,154 @@ {+  "schema_version": 1,+  "type": "component",   "slug": "bq24045dsqr",+  "title": "BQ24045DSQR",+  "brief": "Texas Instruments Battery Management, WSON-10-EP(2x2). Datasheet-verified pinout, KiCad symbol/footprint/3D.",   "version": "0.1.0",-  "type": "component",-  "description": "Texas Instruments Battery Management, WSON-10-EP(2x2). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "license": "CC-BY-SA-4.0",   "tags": [     "component",     "pmic",     "bq24045dsqr"   ],+  "component": {+    "mpn": "BQ24045DSQR",+    "manufacturer": "Texas Instruments",+    "package": "WSON-10-EP(2x2)",+    "pin_count": 11,+    "category": "PMIC",+    "subcategory": "Battery Management",+    "datasheet": "https://www.ti.com/lit/ds/symlink/bq24045dsqr.pdf",+    "parts": {+      "symbol": "bq24045dsqr.kicad_sym",+      "footprint": "bq24045dsqr.kicad_mod",+      "model_3d": "bq24045dsqr.glb",+      "model_3d_step": "bq24045dsqr.step",+      "lbr": "bq24045dsqr.lbr"+    },+    "distributor_links": {},+    "pins": [+      {+        "number": "1",+        "name": "IN",+        "type": "power_in",+        "description": "Input power, connected to external DC supply (AC adapter or USB port). Expected range of bypass capacitors 1uF to 10uF, connect from IN to VSS. Absolute max 30V, operating range 3.5-28V."+      },+      {+        "number": "2",+        "name": "ISET",+        "type": "input",+        "description": "Programs the fast-charge current. External resistor from ISET to VSS defines fast-charge current value. Range is 10.8k (50mA) to 540 ohm (1000mA)."+      },+      {+        "number": "3",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground terminal. Also serves as the reference for the thermal pad, which must be connected to the same potential as VSS."+      },+      {+        "number": "4",+        "name": "PRETERM",+        "type": "input",+        "description": "Programs the current termination threshold (5 to 50% of Iout set by ISET) and sets the pre-charge current to twice the termination current level. Expected programming resistor range is 1k to 10k ohm."+      },+      {+        "number": "5",+        "name": "PG",+        "type": "output",+        "description": "Power-good open-drain output (active low, FET on). Indicates the input voltage is above UVLO and above the OUT (battery) voltage."+      },+      {+        "number": "6",+        "name": "NC",+        "type": "unconnected",+        "description": "Do not make a connection to this terminal (for internal use). Do not route through this terminal."+      },+      {+        "number": "7",+        "name": "ISET2",+        "type": "input",+        "description": "Programs the input/output current limit for the USB or adaptor source. On bq24040/5: High = 500mA max, Low = ISET-programmed, Float = 100mA max."+      },+      {+        "number": "8",+        "name": "CHG",+        "type": "output",+        "description": "Charge-status open-drain output. Low (FET on) indicates charging in progress; open drain (FET off) indicates no charging or charge complete."+      },+      {+        "number": "9",+        "name": "TS",+        "type": "input",+        "description": "Temperature-sense terminal connected to a 10k @ 25 degC NTC thermistor in the battery pack. Floating or pulling high puts part in TTDM Charger mode and disables TS monitoring, timers, and termination. Pulling low disables the IC. If NTC sensing is not needed, connect via 10k to VSS. A 250k from TS to ground prevents entering TTDM when battery-with-thermistor is removed."+      },+      {+        "number": "10",+        "name": "OUT",+        "type": "power_out",+        "description": "Battery connection. System load may also be connected. Expected range of bypass capacitors 1uF to 10uF. Absolute max output continuous current 1.25A."+      },+      {+        "number": "11",+        "name": "PAD",+        "type": "passive",+        "description": "Thermal pad (2x2 mm). There is an internal electrical connection between the thermal pad and the VSS terminal. The thermal pad must be connected to the same potential as VSS on the PCB. Do not use the thermal pad as the primary ground input; VSS must be connected to ground at all times."+      }+    ],+    "provenance": {+      "extractor": "ds2sf",+      "datasheet": {+        "url": "https://www.ti.com/lit/ds/symlink/bq24045dsqr.pdf",+        "pages": 39,+        "sha256": "c508c9c2aedb88aa",+        "source_tier": "mfr"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 11,+        "described": 11,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "metadata": {+    "specs": {+      "Manufacturer": "Texas Instruments",+      "Package": "WSON-10-EP(2x2)",+      "Category": "PMIC",+      "Pins": "11"+    }+  },+  "variants": [+    {+      "mpn": "BQ24045DSQR",+      "kind": "packaging"+    },+    {+      "mpn": "BQ24045DSQRDSQT",+      "kind": "packaging"+    }+  ],+  "sections": [+    "hero",+    "viewers",+    "readme",+    "breadcrumbs",+    "info"+  ],+  "discovery_triggers": [+    "bq24045dsqr"+  ],+  "discovery_pitch": "BQ24045DSQR (Texas Instruments) component page with datasheet-verified CAD.",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  },   "dependencies": {},   "hero": {     "type": "image",@@ -25,10 +166,5 @@     "docs/bq24045dsqr-datasheet.pdf",     "viewers/symbol.html",     "viewers/footprint.html"-  ],-  "visibility": "public",-  "author": {-    "name": "Ray",-    "email": "[email protected]"-  }+  ] }\ No newline at end of file