AVR32DB28-I

@@ -0,0 +1,78 @@+# AVR32DB28-I++**Microchip Tech** · Microcontrollers (MCU/MPU/SOC) · SSOP-28++AVR32DB28-I from Microchip Tech, in a SSOP-28. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | PA7 | bidirectional | General-purpose I/O port A pin 7. Alternate functions: CLKOUT (system clock output), CCL LUT0/LUT1/LUT2 OUT, TCB0 XDIR (alt), SPI0 SS (alt), TCD0 WOD, EVSYS EVOUTA (alt). Supports asynchronous external interrupt detection. |+| 2 | PC0 | bidirectional | General-purpose I/O port C pin 0 in the VDDIO2 power domain (MVIO). Alternate functions: USART1 TxD, SPI1 MOSI, TCA0 WO0 (alt), TCB2 WO, CCL LUT1 IN0. |+| 3 | PC1 | bidirectional | General-purpose I/O port C pin 1 in the VDDIO2 power domain (MVIO). Alternate functions: USART1 RxD, SPI1 MISO, TCA0 WO1 (alt), TCB3 WO (alt), CCL LUT1 IN1. |+| 4 | PC2 | bidirectional | General-purpose I/O port C pin 2 in the VDDIO2 power domain (MVIO). Alternate functions: TWI Fm+ capable, USART1 XCK, SPI1 SCK, TWI0 SDA (host/client, alt position), TCA0 WO2 (alt), EVSYS EVOUTC, CCL LUT1 IN2. |+| 5 | PC3 | bidirectional | General-purpose I/O port C pin 3 in the VDDIO2 power domain (MVIO). Alternate functions: TWI Fm+ capable, USART1 XDIR, SPI1 SS, TWI0 SCL (host/client, alt position), TCA0 WO3 (alt), CCL LUT1 OUT. |+| 6 | VDDIO2 | power_in | Multi-Voltage I/O (MVIO) supply input for PORTC. Independent 1.8-5.5 V supply that sets the digital I/O levels for PC0-PC3 on this device. Requires local decoupling (typ. 1 µF + 100 nF) referenced to the nearest GND pin. |+| 7 | PD1 | bidirectional | General-purpose I/O port D pin 1 in the AVDD power domain. Analog function: ADC0 AIN1, OPAMP0 INP, ZCD0 ZCIN. Alternate digital functions: TCA0 WO1 (alt), CCL LUT2 IN1. |+| 8 | PD2 | bidirectional | General-purpose I/O port D pin 2 in the AVDD power domain. Analog function: ADC0 AIN2, AC0/AC1/AC2 AINP0, OPAMP0 OUT (op-amp 0 output). Alternate digital functions: TCA0 WO2 (alt), EVSYS EVOUTD, CCL LUT2 IN2. |+| 9 | PD3 | bidirectional | General-purpose I/O port D pin 3 in the AVDD power domain. Analog function: ADC0 AIN3, AC0 AINN0, AC1 AINP1, OPAMP0 INN. Alternate digital functions: TCA0 WO3 (alt), CCL LUT2 OUT. |+| 10 | PD4 | bidirectional | General-purpose I/O port D pin 4 in the AVDD power domain. Analog function: ADC0 AIN4, AC1 AINP2, AC2 AINP1, OPAMP1 INP. Alternate digital functions: TCA0 WO4 (alt). |+| 11 | PD5 | bidirectional | General-purpose I/O port D pin 5 in the AVDD power domain. Analog function: ADC0 AIN5, AC1 AINN0, OPAMP1 OUT (op-amp 1 output). Alternate digital functions: TCA0 WO5 (alt). |+| 12 | PD6 | bidirectional | General-purpose I/O port D pin 6 in the AVDD power domain. Analog function: ADC0 AIN6, AC0/AC1/AC2 AINP3, DAC0 OUT (10-bit DAC output). Alternate digital function: CCL LUT2 OUT (alt). |+| 13 | PD7 | bidirectional | General-purpose I/O port D pin 7 in the AVDD power domain. Analog function: VREFA (external analog reference input for ADC/DAC), ADC0 AIN7, AC0/AC1 AINN2, AC2 AINN0/AINN2, OPAMP1 INN. Alternate digital function: EVSYS EVOUTD (alt). |+| 14 | AVDD | power_in | Analog supply pin (1.8-5.5 V). Internally connected to VDD on this device family, but must be externally tied to the same supply as VDD with a dedicated local decoupling capacitor (typ. 1 µF + 100 nF) to the nearest AGND pin. |+| 15 | GND | power_in | Analog ground return (AGND) for the AVDD domain. Must be tied to the board ground plane; provides the return path for the analog decoupling capacitor on AVDD. |+| 16 | PF0 | bidirectional | General-purpose I/O port F pin 0 in the VDD power domain. Special function: XTAL32K1 (input for external 32.768 kHz crystal oscillator). Alternate functions: USART2 TxD, TCA0 WO0 (alt), TCD0 WOA (alt), CCL LUT3 IN0. |+| 17 | PF1 | bidirectional | General-purpose I/O port F pin 1 in the VDD power domain. Special function: XTAL32K2 (feedback/output for external 32.768 kHz crystal oscillator). Alternate functions: USART2 RxD, TCA0 WO1 (alt), TCD0 WOB (alt), CCL LUT3 IN1. |+| 18 | PF6 | input | External RESET input (active-low). Configurable via RSTPINCFG in the System Configuration fuses to act as either the dedicated RESET pin or an input-only PORTF pin. Internal pull-up is present; external pull-up not normally required. A logic-low level triggers a device Reset. |+| 19 | UPDI | bidirectional | Unified Program and Debug Interface - dedicated single-wire pin for programming and debugging the device. Half-duplex UART-like protocol; connect through a series resistor to the programmer's UPDI line. Also usable as GPIO after configuring the UPDI pin function. |+| 20 | VDD | power_in | Main digital supply input (1.8-5.5 V). Provides power to the CPU core, digital peripherals, and PORTA/PORTD/PORTF I/O. Requires local decoupling (typ. 1 µF + 100 nF) referenced to the adjacent GND pin. |+| 21 | GND | power_in | Digital ground return for VDD. Must be tied to the board ground plane; carries the return current for the VDD decoupling capacitor. |+| 22 | PA0 | bidirectional | General-purpose I/O port A pin 0. Special functions: XTALHF1 (input for external high-frequency crystal oscillator), EXTCLK (external clock input). Alternate functions: USART0 TxD, TCA0 WO0, CCL LUT0 IN0. |+| 23 | PA1 | bidirectional | General-purpose I/O port A pin 1. Special function: XTALHF2 (feedback/output for external high-frequency crystal oscillator). Alternate functions: USART0 RxD, TCA0 WO1, CCL LUT0 IN1. |+| 24 | PA2 | bidirectional | General-purpose I/O port A pin 2. Fm+ (1 MHz) TWI capable. Alternate functions: USART0 XCK, TWI0 SDA (host/client), TCA0 WO2, TCB0 WO, EVSYS EVOUTA, CCL LUT0 IN2. |+| 25 | PA3 | bidirectional | General-purpose I/O port A pin 3. Fm+ (1 MHz) TWI capable. Alternate functions: USART0 XDIR, TWI0 SCL (host/client), TCA0 WO3, TCB1 WO, CCL LUT0 OUT. |+| 26 | PA4 | bidirectional | General-purpose I/O port A pin 4. Alternate functions: USART0 TxD (alt), SPI0 MOSI, TCA0 WO4, TCD0 WOA. |+| 27 | PA5 | bidirectional | General-purpose I/O port A pin 5. Alternate functions: USART0 RxD (alt), SPI0 MISO, TCA0 WO5, TCD0 WOB. |+| 28 | PA6 | bidirectional | General-purpose I/O port A pin 6. Alternate functions: USART0 XCK (alt), SPI0 SCK, TCD0 WOC, CCL LUT0 OUT (alt). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Microchip Tech |+| Package | SSOP-28 |+| Category | Embedded Processors & Controllers |+| Pins | 28 |++## Ordering variants++Same part, different packaging or reel option.++- `AVR32DB28-II/SO`+- `AVR32DB28-IT-I/SO`+- `AVR32DB28-IE/SO`+- `AVR32DB28-IT-E/SO`+- `AVR32DB28-II/SS`+- `AVR32DB28-IT-I/SS`+- `AVR32DB28-IE/SS`+- `AVR32DB28-IT-E/SS`+- `AVR32DB28-II/SP`+- `AVR32DB28-IE/SP`++## CAD (KiCad official)++- Symbol: `AVR32DB28-I`+- Footprint: `Package_SO:SSOP-28_5.3x10.2mm_P0.65mm`+- 3D model: SSOP-28 (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Microchip Tech datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8590442912581382144) (None pp, sha256 `adfeb5005d481e53`, retrieved 2026-08-17, tier: lcsc)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/avr32db28-i-datasheet.pdf)

@@ -0,0 +1,34 @@+{+  "slug": "avr32db28-i",+  "version": "0.1.0",+  "type": "component",+  "description": "Microchip Tech Microcontrollers (MCU/MPU/SOC), SSOP-28. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "embedded processors & controllers",+    "avr32db28-i"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "avr32db28-i.kicad_sym",+    "avr32db28-i.kicad_mod",+    "avr32db28-i.glb",+    "avr32db28-i.step",+    "avr32db28-i.lbr",+    "docs/hero.png",+    "docs/avr32db28-i-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "visibility": "public",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file