AT24C64D-SSHM-T

@@ -32,7 +32,7 @@         "number": "1",         "name": "A0",         "type": "input",-        "description": "Device address input bit 0. Hardwired to VCC or GND to set the LSB of the 3-bit device-select field in the I\u00b2C slave address, allowing up to eight AT24C64D devices on a single 2-wire bus. Internal pull-down to GND when left floating; Atmel recommends tying to a known state with \u226410 k\u03a9 pull-up if used with VCC."+        "description": "Device address input bit 0. Hardwired to VCC or GND to set the LSB of the 3-bit device-select field in the I²C slave address, allowing up to eight AT24C64D devices on a single 2-wire bus. Internal pull-down to GND when left floating; Atmel recommends tying to a known state with ≤10 kΩ pull-up if used with VCC."       },       {         "number": "2",@@ -56,25 +56,25 @@         "number": "5",         "name": "SDA",         "type": "bidirectional",-        "description": "I\u00b2C serial data. Bidirectional open-drain line; requires an external pull-up to VCC. Wire-ORable with any number of other open-drain / open-collector devices on the same 2-wire bus. Input capacitance 8 pF max."+        "description": "I²C serial data. Bidirectional open-drain line; requires an external pull-up to VCC. Wire-ORable with any number of other open-drain / open-collector devices on the same 2-wire bus. Input capacitance 8 pF max."       },       {         "number": "6",         "name": "SCL",         "type": "input",-        "description": "I\u00b2C serial clock input. Positive-edge clocks data into the EEPROM and negative-edge clocks data out. Schmitt-triggered, filtered input; 400 kHz at 1.7 V, up to 1 MHz at 2.5-5.0 V. Input capacitance 6 pF max."+        "description": "I²C serial clock input. Positive-edge clocks data into the EEPROM and negative-edge clocks data out. Schmitt-triggered, filtered input; 400 kHz at 1.7 V, up to 1 MHz at 2.5-5.0 V. Input capacitance 6 pF max."       },       {         "number": "7",         "name": "WP",         "type": "input",-        "description": "Write-Protect input. Tie to GND for normal read/write operation; tie to VCC to inhibit all write operations (full array protected). Internal pull-down to GND when floating; Atmel recommends always tying to a known state (\u226410 k\u03a9 if using a pull-up)."+        "description": "Write-Protect input. Tie to GND for normal read/write operation; tie to VCC to inhibit all write operations (full array protected). Internal pull-down to GND when floating; Atmel recommends always tying to a known state (≤10 kΩ if using a pull-up)."       },       {         "number": "8",         "name": "VCC",         "type": "power_in",-        "description": "Device power supply, 1.7 V to 5.5 V. Typical supply currents: 0.4 mA read / 2.0 mA write at 5.0 V; standby current 1 \u00b5A (1.7 V) / 6 \u00b5A (5.0 V). Absolute max 6.25 V."+        "description": "Device power supply, 1.7 V to 5.5 V. Typical supply currents: 0.4 mA read / 2.0 mA write at 5.0 V; standby current 1 µA (1.7 V) / 6 µA (5.0 V). Absolute max 6.25 V."       }     ],     "provenance": {@@ -138,5 +138,8 @@     "docs/at24c64d-sshm-t-datasheet.pdf",     "viewers/symbol.html",     "viewers/footprint.html"-  ]+  ],+  "visibility": {+    "public": true+  } }\ No newline at end of file