ap5054ces6

@@ -33,5 +33,66 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "AP5054CES6",+    "manufacturer": "Wuxi Chipown Micro electronics",+    "package": "SOT-23-6L",+    "pin_count": 6,+    "category": "Battery Management",+    "parts": {+      "symbol": "ap5054ces6.kicad_sym",+      "footprint": "ap5054ces6.kicad_mod",+      "model_3d": "ap5054ces6-etched.glb",+      "model_3d_plain": "ap5054ces6.glb",+      "model_3d_step": "ap5054ces6-etched.step",+      "model_3d_step_plain": "ap5054ces6.step",+      "lbr": "ap5054ces6.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "CHRG",+        "type": "output",+        "description": "Open-drain charge status indicator. Pulled low through an internal N-channel MOSFET while the battery is charging; high-impedance when the charge cycle completes or the part enters UVLO. Rated for Ichrg up to ~5 mA with Vol ≈ 0.68-0.8 V."+      },+      {+        "number": "2",+        "name": "GND",+        "type": "power_in",+        "description": "Device power ground reference."+      },+      {+        "number": "3",+        "name": "BAT",+        "type": "power_out",+        "description": "Battery connection pin. Sources charge current to a single-cell Li-ion battery and regulates the final float voltage to 4.2 V via an internal precision resistor divider. Disconnected in shutdown mode; absolute-maximum current 750 mA."+      },+      {+        "number": "4",+        "name": "VCC",+        "type": "power_in",+        "description": "Positive supply input for the charger. Operating range 4.25 V to 6.5 V; bypass with at least 1 µF to GND. When VCC - VBAT falls below ~30 mV the part enters shutdown and IBAT drops below 2 µA."+      },+      {+        "number": "5",+        "name": "STDBY",+        "type": "output",+        "description": "Open-drain end-of-charge status indicator. Pulled low through an internal switch when the charge cycle is complete, otherwise high-impedance. Rated for Istdby up to ~5 mA with Vol ≈ 0.68-0.8 V."+      },+      {+        "number": "6",+        "name": "PROG",+        "type": "bidirectional",+        "description": "Charge current program, monitor and shutdown pin. Connect a 1% resistor RPROG from PROG to GND to set charge current: IBAT = (VPROG / RPROG) × 1000. VPROG is regulated to 0.1 V in trickle/precharge and 1 V in constant-current mode. Disconnecting RPROG lets an internal 3 µA source pull PROG above the 1.21 V shutdown threshold, driving the charger into shutdown (Icc ≈ 25 µA); the pin is internally clamped at ~2.4 V."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}