component
ALED6001TR
Public Made by Adomby adom
STMicroelectronics LED Drivers, TSSOP-16-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+53@@ -0,0 +1,53 @@+# ALED6001TR++**STMicroelectronics** · LED Drivers · TSSOP-16-EP++ALED6001TR from STMicroelectronics, in a TSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | PWMI | input | Device enable and PWM dimming control input; turn-on threshold 1.34 V to 1.65 V, dimming frequency 0.1 to 20 kHz, shutdown when held low more than 10 ms. |+| 2 | FSW | input | Switching frequency setting via a resistor to SGND (100 kHz to 1 MHz) and synchronization clock input; tied high (e.g. to LDO3) sets 600 kHz. |+| 3 | XFAULT | output | Open-drain fault indicator output, pulled low by the device in case of a faulty condition. |+| 4 | LDO3 | power_out | 3.3 V linear regulator output and device supply; connect a 1 µF (typ.) MLCC bypass to SGND close to the chip. |+| 5 | SGND | power_in | Signal ground, return for analog circuitry; all setting components must refer to this pin. |+| 6 | COMP | passive | Boost controller loop compensation; a simple RC series must be connected between this pin and SGND. |+| 7 | ADIM | input | Analog dimming control input; output current is linearly controlled by the voltage applied (0.3 V to 1.2 V). |+| 8 | OVFB | input | Output overvoltage protection feedback input; connect to the central tap of a resistor divider at the output (1.2 V typ. threshold). |+| 9 | CSNS | input | Boost controller power switch current sensing input; connect to the source of the external power MOSFET (OCP threshold 360 mV typ.). |+| 10 | PWMO | output | PWM dimming control output in phase with PWMI, for direct drive of a dimming N-channel MOSFET. |+| 11 | PGND | power_in | Power ground, return for the VDR linear regulator and gate drivers and reference for power MOSFET current sensing. |+| 12 | GATE | output | Power switch gate driver output; connect to the gate of the power MOSFET through a small value resistor. |+| 13 | VDR | power_out | 5 V linear regulator output and gate driver supply; connect a 1 µF (typ.) MLCC bypass to PGND close to the chip. |+| 14 | VIN | power_in | Supply voltage input, 5.5 V to 36 V; connect a 1 µF (typ.) MLCC between this pin and PGND close to the chip. |+| 15 | VFBN | input | Output current differential sensing input, negative terminal; connect to the hot (load side) terminal of the high-side sensing resistor. |+| 16 | VFBP | input | Output current differential sensing input, positive terminal; connect to the quiet (output capacitor side) terminal of the high-side sensing resistor. |+| 17 | TPAD | power_in | Thermal pad; connect to a suitable ground plane area for heat dissipation, electrically connected to PGND and SGND. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | STMicroelectronics |+| Package | TSSOP-16-EP |+| Category | LED Drivers |+| Pins | 17 |++## CAD (KiCad official)++- Symbol: `ALED6001TR`+- Footprint: `Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm`+- 3D model: TSSOP-16-EP (KiCad packages3D, STEP)+- 3D model files: `aled6001tr-etched.step` / `aled6001tr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `aled6001tr.step` / `aled6001tr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588938503149666304) (26 pp, sha256 `d15a9cebbf6b9659`, retrieved 2026-10-07, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/aled6001tr-datasheet.pdf)
page.jsonadded+255@@ -0,0 +1,255 @@+{+ "slug": "aled6001tr",+ "version": "0.1.0",+ "type": "component",+ "description": "STMicroelectronics LED Drivers, TSSOP-16-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "led drivers",+ "aled6001tr",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "aled6001tr.kicad_sym",+ "aled6001tr.kicad_mod",+ "aled6001tr.glb",+ "aled6001tr.step",+ "aled6001tr.lbr",+ "docs/hero.png",+ "docs/aled6001tr-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "aled6001tr-hero.glb",+ "aled6001tr-hero.overlay.json"+ ],+ "component": {+ "mpn": "ALED6001TR",+ "manufacturer": "STMicroelectronics",+ "package": "TSSOP-16-EP",+ "pin_count": 17,+ "category": "LED Drivers",+ "subcategory": "LED Drivers",+ "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588938503149666304",+ "parts": {+ "symbol": "aled6001tr.kicad_sym",+ "footprint": "aled6001tr.kicad_mod",+ "model_3d": "aled6001tr-hero.glb",+ "model_3d_plain": "aled6001tr.glb",+ "model_3d_step": "aled6001tr-etched.step",+ "model_3d_step_plain": "aled6001tr.step",+ "lbr": "aled6001tr.lbr"+ },+ "distributor_links": {+ "lcsc": "C2678780",+ "digikey": "497-15390-2-ND",+ "mouser": "511-ALED6001TR"+ },+ "distributor_check": {+ "checked_at": "2026-10-07T20:48:11Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "497-15390-2-ND",+ "status": "found",+ "lifecycle": "Active"+ },+ "mouser": {+ "pn": "511-ALED6001TR",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "PWMI",+ "type": "input",+ "description": "Device enable and PWM dimming control input; turn-on threshold 1.34 V to 1.65 V, dimming frequency 0.1 to 20 kHz, shutdown when held low more than 10 ms."+ },+ {+ "number": "2",+ "name": "FSW",+ "type": "input",+ "description": "Switching frequency setting via a resistor to SGND (100 kHz to 1 MHz) and synchronization clock input; tied high (e.g. to LDO3) sets 600 kHz."+ },+ {+ "number": "3",+ "name": "XFAULT",+ "type": "output",+ "description": "Open-drain fault indicator output, pulled low by the device in case of a faulty condition."+ },+ {+ "number": "4",+ "name": "LDO3",+ "type": "power_out",+ "description": "3.3 V linear regulator output and device supply; connect a 1 µF (typ.) MLCC bypass to SGND close to the chip."+ },+ {+ "number": "5",+ "name": "SGND",+ "type": "power_in",+ "description": "Signal ground, return for analog circuitry; all setting components must refer to this pin."+ },+ {+ "number": "6",+ "name": "COMP",+ "type": "passive",+ "description": "Boost controller loop compensation; a simple RC series must be connected between this pin and SGND."+ },+ {+ "number": "7",+ "name": "ADIM",+ "type": "input",+ "description": "Analog dimming control input; output current is linearly controlled by the voltage applied (0.3 V to 1.2 V)."+ },+ {+ "number": "8",+ "name": "OVFB",+ "type": "input",+ "description": "Output overvoltage protection feedback input; connect to the central tap of a resistor divider at the output (1.2 V typ. threshold)."+ },+ {+ "number": "9",+ "name": "CSNS",+ "type": "input",+ "description": "Boost controller power switch current sensing input; connect to the source of the external power MOSFET (OCP threshold 360 mV typ.)."+ },+ {+ "number": "10",+ "name": "PWMO",+ "type": "output",+ "description": "PWM dimming control output in phase with PWMI, for direct drive of a dimming N-channel MOSFET."+ },+ {+ "number": "11",+ "name": "PGND",+ "type": "power_in",+ "description": "Power ground, return for the VDR linear regulator and gate drivers and reference for power MOSFET current sensing."+ },+ {+ "number": "12",+ "name": "GATE",+ "type": "output",+ "description": "Power switch gate driver output; connect to the gate of the power MOSFET through a small value resistor."+ },+ {+ "number": "13",+ "name": "VDR",+ "type": "power_out",+ "description": "5 V linear regulator output and gate driver supply; connect a 1 µF (typ.) MLCC bypass to PGND close to the chip."+ },+ {+ "number": "14",+ "name": "VIN",+ "type": "power_in",+ "description": "Supply voltage input, 5.5 V to 36 V; connect a 1 µF (typ.) MLCC between this pin and PGND close to the chip."+ },+ {+ "number": "15",+ "name": "VFBN",+ "type": "input",+ "description": "Output current differential sensing input, negative terminal; connect to the hot (load side) terminal of the high-side sensing resistor."+ },+ {+ "number": "16",+ "name": "VFBP",+ "type": "input",+ "description": "Output current differential sensing input, positive terminal; connect to the quiet (output capacitor side) terminal of the high-side sensing resistor."+ },+ {+ "number": "17",+ "name": "TPAD",+ "type": "power_in",+ "description": "Thermal pad; connect to a suitable ground plane area for heat dissipation, electrically connected to PGND and SGND."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: The exposed thermal pad (listed as TPAD in Table 2, electrically tied to PGND and SGND) has no numbe; The package is printed as HTSSOP-16 (exposed pad) in Table 1 and Section 8.1; the 'TSSOP-16' label a",+ "exposed pad 17 added from the footprint"+ ],+ "pages_sent": 26,+ "cost_usd": 0.0962,+ "at": "2026-10-07T20:47:50"+ },+ "datasheet": {+ "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588938503149666304",+ "pages": 26,+ "sha256": "d15a9cebbf6b9659",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 17,+ "described": 17,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "aled6001tr.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6.4,+ 5,+ 1.1+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "7982746831c0bd23f4690608869ad67776faae5c762fb0376666126a3998921b",+ "checked": "2026-10-07",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "aled6001tr-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6.4,+ 5,+ 1.1+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "ffb2629330cdb195ad2daf1a506c9132c19f495e25df009b868b249c03987709",+ "checked": "2026-10-07",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}