adt75armz-reel-tudi

@@ -33,5 +33,78 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "ADT75ARMZ-REEL-TUDI",+    "manufacturer": "Tudi",+    "package": "MSOP-8",+    "pin_count": 8,+    "category": "Temperature and Humidity Sensor",+    "parts": {+      "symbol": "adt75armz-reel-tudi.kicad_sym",+      "footprint": "adt75armz-reel-tudi.kicad_mod",+      "model_3d": "adt75armz-reel-tudi-etched.glb",+      "model_3d_plain": "adt75armz-reel-tudi.glb",+      "model_3d_step": "adt75armz-reel-tudi-etched.step",+      "model_3d_step_plain": "adt75armz-reel-tudi.step",+      "lbr": "adt75armz-reel-tudi.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "SDA",+        "type": "bidirectional",+        "description": "Serial data pin for the SMBus/I2C interface. Open-drain output; requires an external pull-up resistor (5 kΩ recommended, pin current must not exceed 3 mA)."+      },+      {+        "number": "2",+        "name": "SCL",+        "type": "input",+        "description": "Serial clock pin for the SMBus/I2C interface. Open-drain; requires an external pull-up resistor (5 kΩ recommended). Supports fast mode up to 400 kHz and high-speed mode up to 2.75 MHz."+      },+      {+        "number": "3",+        "name": "ALERT",+        "type": "output",+        "description": "Overtemperature alert output. Open-drain; requires an external pull-up resistor. Polarity is programmable via the POL bit (active-low by default); operates in comparator or interrupt mode as configured by the TM bit."+      },+      {+        "number": "4",+        "name": "GND",+        "type": "power_in",+        "description": "Ground reference pin for the device."+      },+      {+        "number": "5",+        "name": "A2",+        "type": "input",+        "description": "I2C slave address select input, bit 2. Tie to V+ or GND to set one of eight possible 7-bit slave addresses (1001xxx)."+      },+      {+        "number": "6",+        "name": "A1",+        "type": "input",+        "description": "I2C slave address select input, bit 1. Tie to V+ or GND to set the slave address."+      },+      {+        "number": "7",+        "name": "A0",+        "type": "input",+        "description": "I2C slave address select input, bit 0. Tie to V+ or GND to set the slave address."+      },+      {+        "number": "8",+        "name": "V+",+        "type": "power_in",+        "description": "Positive supply voltage input. Operating range 1.4 V to 5.5 V per pin description (recommended supply 3.0 V to 5.5 V per datasheet front page). Decouple with a 0.01 μF bypass capacitor to GND."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}