← Commit history

Record side-fan review clip and remaining prototype acceptance work

John Lauer ·aa80121a2e · ·parent e132381
3 files changed +29
docs/completion-plan.md+15
@@ -1,5 +1,15 @@ # Active completion plan +## Current authorized extension: probing simulation (2026-10-12)++The latest user request supersedes the earlier simulator exclusion below: build the electronic-load test simulation in adom-aiflow-probing, animate the fan from explicitly simulated RPM, record key steps, and feed probe-access failures back into board design. Correct USB-C edge placement and use large corner pins for this repeatedly handled assembly. Physical cell actuation, fabrication, flashing and YouTube publication remain outside authorization.++Board32 remains the adopted baseline. `probing-flow/design-candidate/` holds an unadopted 72 x 104 mm revision with large pins, USB-C at the edge and a relocated TP3/TP7/TP11 probe bank. Native DRC has zero electrical errors and zero unconnected; silkscreen/library warnings remain. The new full assembly GLB preserves the named fan rotor animation. `probing-preview/` is the isolated probing run; explicit PCB substrate metadata yields correct 5.65 mm installed board top and four aligned large pins. Ground-contact reach and full cooling-assembly collision coverage are the next open gates. See `probing-flow/progress.json` and `videos/probing/clips.json` for current evidence; no simulator recording or physical qualification is claimed yet.++AIFlow pin-selection guidance/checks are published as source commit `74561044c30bf421afec3bb52d14649ab6a0cfd6`; registry installation is separate. Probing app changes are still local at `/home/adom/project/load-probing-20261012` pending integration validation and latest-source reconciliation. Do not mark the candidate adopted or the probing flow done until the actual gates pass.++## Earlier phase record (retained for provenance)+ Current phase (user clarified 2026-10-12): finish this board through AIFlow and its design deliverables, wiki assets and reviewed build film. The probing workcell simulator and physical bench-test prototype are later phases; their unmeasured status must not be treated as a requirement to build them in this thread. Preserve engineering design gates and label modeled results honestly. Supporting releases or status answers do not complete this objective. Do not order, fabricate, flash or publish to YouTube without authorization.  ## Resume from this state@@ -193,3 +203,8 @@ Latest user presentation update, 2026-10-12: user explicitly permits Pup again. Continuation 2026-10-12: Fields tour recorded and published (283.2s raw,28.4s 10x); wiki playback and contact sheet reviewed. Exact Pup-session recording fix and failed-tour proof fix published directly as f876b3ee6f63c8bbaf5e537a05aff85d2cec3144;167workspace tests, production check/build, component/widget and7silkscreen scripts pass. Placement proof refreshed for current spec,104poses unchanged. Native8-net tour completed. Board32 silkscreen review measures309labels,0text/obstacle intersections,104current reference/value groups and0hierarchy exceptions; native top/underside artwork and3D reviewed. J10/TEMP correction is already present. Evidence checkpoints/board32-silkscreen-current; external silkscreen proof records actual review without geometry edits. AIFlow now at3D, walkthrough recording in progress. Native short silk inspection recorder reported failed timestamp repair; its decoded27.6s footage is review evidence with timing caveat, not an accurate action-duration claim. Selected cooling sensitivity finds only0.619C nominal margin; physical qualification remains deferred and output locked.  Latest continuation: AIFlow finish and export checks pass; delivery/video remain open. Published selected-cooling envelope assembly preserves fan animation and wiring; 139 native takes indexed. Dimensional sensitivity exposes fixed-height contact-stack accommodation as unresolved manufacturing design work. Prototype measurement-based spacer worksheet added; nominal example is not measured evidence. Formal stack and thermal gates unchanged. Next: establish interface material/process and a controlled retention scheme, then reconcile the release drawing. Final film still needs clip approval and working narration service.+++### Side-fan mechanical candidate — 13 October 2026++User requested side fan, stronger carrier and Q1 heatsink. Published mechanical/side-fan-r1: fan 16 mm outside PCB, reinforced connected carrier with through-bolted clamps and 6 mm gussets, nominal ATS 50 x 50 x 25 mm sink with insulated Q1 contact. Geometry screening has no unexpected component-body intersections; carrier is one valid solid. New cooling path reopens thermal acceptance; physical strength, retention, airflow and full probe sequence validation remain open. Board32 and native PCB unchanged. Separate probing-preview-sidefan study reports 14 existing measurement entries and five entries relying on three proposed pads (not fabricated/routed). Three-pad routing/native DRC and complete plan/collision checks remain required. README, hero and three-page datasheet updated. Clean 30.27 s native CAD review clip retained; first overlapping-model take rejected.
videos/probing/clips.json+14
@@ -36,5 +36,19 @@     "description": "Pup published project page tour: assembly hero, README gallery and three-page project datasheet",     "verifiedAction": "Actual page navigation and camera command; no workcell simulation or hardware test",     "sha256": "336d2bd94f936803ba800299274f671f99c73ca5ca7a72324e2879ae9ed790b5"+  },+  {+    "file": "videos/probing/window-27199580-20261013-014042.mp4",+    "description": "Rejected first side-fan comparison take",+    "demoEligible": false,+    "reason": "Old and new models overlapped before viewer clearScene fix."+  },+  {+    "file": "videos/probing/window-27199580-20261013-015154.mp4",+    "durationSeconds": 30.266667,+    "description": "Side-mounted fan and reinforced carrier orbit, heatsink hidden to reveal Q1 thermal contact then restored",+    "verifiedAction": "Native Pup window recording; decoded frame at 11 s reviewed. CAD review only; no hardware or probing simulation proof.",+    "timingCaveat": "Recorder timestamp repair declined because sample count differed; ffprobe duration recorded separately.",+    "sha256": "5d81c0321ae2e23be05299df26f07f867a1cfc9f66a25e50c6269ed81d928be1"   } ]
videos/probing/window-27199580-20261013-015154.mp4added
⋯ 1 unchanged line ⋯